Audiovox TV55 User's Manual
Contents
1. 3 Run the RG6 Coaxial Cable through the hole into the home Note Please see Water Damage Prevention for proper sealing of the hole GSAL 16 Water Damage Prevention At the point where your coaxial cable lead enters the house you should allow for some slack in the coaxial cable as a drip loop This will prevent moisture from running down the coaxial cable and entering the house Run the coaxial cable approximately six inches below the wall entry point and then turn it upwards towards this spot See Fig 16 Any moisture that accumulates on the coaxial cable will drip off in the bend instead of running into the house You should seal the point where the cable enters your home with a rubber weather insulator or silicone caulking not included An F connector wall plate can be used inside the home to cover the inside portion of the whole You can typically find an F connector wall plate at any local Electronics or Hardware store Fig 16 For Use With a Satellite Dish GSAL 17 TV55 Installation Procedure for use with a Satellite Dish If you have a satellite dish it is possible to install the TV55 using the same wiring as the satellite dish To do this you will need to purchase a set of diplexers Terk model BDS P1 The instructions listed below are for a basic satellite system If you have a more complex satellite system and wish to install the TV55 in this manor please call TERK Sup2. 4 Split washers Positioning the TV55 GSAL The TV55 MUST be mounted horizontally See Fig 1 with the front of the TV55 facing the general direction of the TV station s broadcasting transmitters See Fig 2 The higher the elevation of the antenna the better the reception performance will be Pointing the Antenna Towards the Broadcast Tower 1 Go to www terk com and click on the Antenna Locator link 2 Enter your home address and then Submit 3 Click View Street Level Map to see in which direction you should face your antenna towards TERIC V55 Fig 1 GSAL On the side of the house facing the broadcast tower Fig 2 Wrong Not on the side of the house facing the broadcast tower Mounting the TV55 Antenna GSAL Mounting Options The TV55 can be mounted in many ways both indoors such as on a wall or in an attic and outdoors such as on a mast on a wall or either under a window or a roof s eave Decide where you will mount the TV55 and follow the appropriate directions Indoors Outdoors using Wall Mount Brackets Indoors Select a spot in your home where the antenna may be positioned horizontally and out of the way of large metal objects which may cause interference Be sure the antenna Is not in a position where it could easily fall or be damaged Note Never install the antenna onto a metal surface This wil
3. Injector should always be located indoors i 1 TO TV 1 TOT 2 Running Cable GSAL 19 Under a Window 1 Connect one end of the supplied RG coaxial cable to the F connector output on the end of the TV55 and connect the other end to the 9 3 4 white flat cable Note If the supplied RG6 Coaxial Cable is not long enough you can purchase additional lengths of RG6 Coaxial Cable from the retailer you purchased the TV55 antenna from 2 Run the white flat cable through an open window Make sure that it runs under the window to ensure proper window closure See Fig 15 Run a coaxial cable not supplied from the inside end of the 9 white flat cable towards your television set and connect the coaxial cable to the supplied Power Injector on the terminal labeled TO ANTENNA Through a Wall If you do not use the supplied 9 3 4 white flat cable to run your coaxial cable through a window and instead choose to drill through an external wall be careful to avoid contact with any power lines telephone lines cable TV lines or plumbing 1 Connect one end of the supplied RG coaxial cable to the F connector output on the end of the TV55 Note If the supplied RG6 Coaxial Cable is not long enough you can purchase additional lengths of RG6 Coaxial Cable from the retailer you purchased the antenna from 2 Drill a hole in an exterior wall matching the diameter of the RG6 coaxial cable
4. 290 6650 About Your New TERK TV55 Antenna GSAL 3 Your TERK TV55 antenna is designed for both single and multi family homes It s specifically engineered to provide superior reception of high definition HDTV digital television DTV and VHF UHF TV channels in most viewing locations The TV55 s unique antenna technology and patented Dual Mode integrated powered amplifier produce the clearest cleanest signals available from a compact unobtrusive design that blends well with any home decor The TV55 s weatherproof hermetically sealed housing offers ultra reliable performance year after year No assembly of the antenna is required The TV55 comes with all necessary mounting hardware for flexible placing indoors or outdoors Your TV55 Antenna Includes 1 TV55 Amplified Antenna 1 Power injector with 110vAC to DC power adapter 4 1 Mast Mount Base 4 1 Mast Mount Cover GSAL 2 Window Mount Brackets 2 piece assembly consisting of 1 Window Frame Bracket 1 Channel Insert Bracket 2 Wall Mount Cam locks 1 36 RG6 coaxial cable 1 9 3 4 Flat coaxial cable 2 10 Plastic wall anchors 2 8 Plastic wall anchors 1 1 4 20 x 1 1 2 Hex head bolt 1 1 4 20 x 2 1 2 Hex head bolt 2 1 4 20 x 3 4 Hex head bolts 1 1 4 20 Wing nut 2 1 4 20 Hexagon nuts 2 10 x 2 1 2 Flat head screws 2 8 x 1 1 2 Pan head screws 2 1
5. Shooting GSAL 18 gt lam not getting any channels above channel 13 Most TV s today are cable ready When a cable ready TV is in the CABLE or CATV mode and you try to use an antenna with it you will not receive any channels above 13 Access the TV s set up menu and switch it from CABLE or CATV mode to ANTENNA or AIR mode am not receiving channels clearly Turn the Power Injector on and off Determine which position is best suited to receive your channels NOTE Some channels may come in clearer with the Power Injector turned off am not receiving all channels Reposition the TV55 to a different location such as the other side of the house or to a higher location Obstructions such as other houses or buildings large trees mountains and water towers can cause poor reception As a general rule the higher the antenna is mounted the better your reception will be am seeing ghosts or double images in the picture Ghosting is caused by multi path This happens when the antenna signal reflects off of a tall obstruction and hits your antenna multiple times Each reflection causes a ghost To solve this problem try repositioning the TV55 to a location where the reflections are prevented from hitting it such as the other side of the house or to a higher location Need more help C all 1 800 290 6650 for TERK s Technical Support Department Monday through Friday 9 00AM to 5 00PM EST or conta
6. TV55 Owner s Manual Indoor Outdoor TERK Amplified TV Antenna by AUDIOVOX Safety Precautions GSAL Warning Use extreme caution when installing or removing an outdoor antenna that is located close to overhead wires such as power lines telephone lines or cable TV lines If any part of the antenna makes contact with overhead power lines touching the antenna or the antenna cable can cause electrocution and death If the antenna Is in contact with any type of overhead wires call your power company and ask them to send a qualified technician to remove the antenna Do not attempt to remove it yourself Important Safety Precautions Many do it yourself and professional antenna installers are injured or killed each year by electric shock While anyone can see the obvious danger of falling the most resourceful sometimes fail to recognize overhead wires as being potentially lethal To touch any part of the antenna to these overhead wires is the same as touching the wires with your bare hand A very serious shock is almost sure to result when contacting an electrical wire and in the case of primary wires on the top of poles the shock is like being struck by a bolt of lightning Many power wires are within 20 to 25 feet of the ground and could easily be touched by an assembled antenna GSAL Please read and follow these important safety precautions e Be sure to select an antenna site well away from all overhead w
7. ct us at www audiovox com If your TV has a connection not mentioned in this manual contact Terk for the appropriate adapter Limited Warranty Audiovox Corporation Audiovox warrants this product against defects in materials or workmanship for one 1 year from the date of purchase During this period this product will be replaced without charge This warranty does not cover any damage due to acts of nature commercial use accident misuse abuse or negligence This warranty is only valid in the USA Replacement as provided under this warranty is the exclusive remedy of the consumer Audiovox shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on this product except to the extent that limitations of this sort are prohibited by applicable law THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURCHASE EXCEPT TO THE EXTENT THAT IMPLIED WARRANTIES OR EITHER SORT ARE REQUIRED BY APPLICABLE LAW AND IN SUCH CASE EACH WARRANTY IS LIMITED IN DURATION TO THE ONE YEAR A E amp A For Customer Service Visit Our Website At For customer service and www audiovox com P a Product Information Photos technical information 1 800 290 6650 FAQ s Owner s Manuals TERK and the TERK logo are registered trademarks of AUDIOVOX Corp 44P008A
8. ires e Do not try to guess which overhead wires carry high voltage Check with the Power Company e f you notice anything making contact with the overhead wires call the Power Company to have it removed safely Do not run the downlead cable over power wires e Get help from a qualified professional when removing the old antenna if there is any doubt of clearing overhead wires e Never install the antenna outdoors at night when it is windy or during rain or snow e Make sure the antenna installation is secure e Do not stand on lean on hang from or hang anything on the antenna once it is mounted Lightning Protection and Grounding Always plug your TV and other electronics devices into a quality surge protector for maximum protection against lightning and power surges e Do not run the downlead cable over power wires e Make sure the antenna downlead is connected to suitable lightning arrestors All outdoor antenna installations should be properly grounded To effectively protect the installation the coaxial cable s should be grounded before they enter the house The grounding of the coaxial cable is made using a ground block and copper wire not supplied For information and the materials needed to ground your antenna installation visit your local electronics store If you are not sure how to install the grounding block and rod please consult your local retailer or TERK s Technical Support Department at 1 800
9. l seriously degrade reception quality Do not mount the antenna indoors if you have stucco walls or aluminum siding Outdoors Your TV55 antenna may also be mounted outdoors on a roof s eave or outside a window Mount the antenna away from trees or other obstructions as higher frequencies may be affected by these obstructions Note Mounting the antenna on aluminum siding or any metal surface will greatly degrade reception For the optimum performance mount the antenna horizontally with the front aiming at the general direction of the TV station s broadcasting transmitters The higher the antennas elevation the better the reception performance will be Warning Never hang anything from or attach any weight to the mounting brackets or the antenna 1 Locate 2 Wall Mount Cam locks 2 10 plastic wall anchors 2 Mark the mounting surface you have chosen Make a pencil mark approximately 11 in from one end of the antenna Along a level horizontal line make a second mark 23 from the first See Fig 3 GSAL 3 Use the 10 screws and plastic anchors to secure each of the Wall Mount Cam lock units into the wall at the marks made in Step 2 As an alternative mounting method you may choose to use longer screws directly attached into wood supports wall studs or use a different wall anchoring device Make sure the Cam lock wings are vertical See Fig 3 4 Carefully position the TV55 antenna so that the Ca
10. m locks slide into the channel on the rear of the antenna See Fig 4 5 Once the Cam locks are in the channel properly turn the Cam locks 1 4 turn to secure the antenna Do not turn these more than necessary to lock into the antenna and secure it snugly See Fig 5 Note If the Cam locks do not lock securely you may need to adjust the location of the Cam locks along the channel 6 Skip to the Connecting the TV55 Antenna to a TV section to finish installation Fig 4 Fig 5 Mounting the TV55 Antenna continued GSAL Outdoors using Window Mounting 1 Locate 1 Channel Insert 2 3 4 bolts 2 Hex head nuts 2 Split washers 2 Window Mount Brackets Plastic anchors and screws depending on the material being mounted to 2 Break the Channel Insert into 2 pieces at the score line See Fig 6 Note Do not break Channel Insert if mounting on a mast See the Mast Mounting section Oooo ooo 2e gt oR Fig 6 GSAL 10 3 Insert a hex head bolt into each of the Channel Inserts Insure that the bolt head fits into the hexagon recess on the insert 4 Slide the Channel Inserts into the channel on the back of the TV55 the bolts should be pointing away from the antenna See Fig 7 Fig 7 5 Unscrew the Window Mount Bracket so you can separate the two pieces Channel Insert Bracket and Window Frame Bracket keep the screw since you will need to use it again 6 At
11. nting the TV55 Antenna continued GSAL 13 4 Determine mast size The supplied Mast Bracket will fit a 11 4 or 1 1 2 mast If the mast being used is 1 1 2 in diameter the tabs on the Mast Bracket Cover needs to removed using a pair of pliers See Fig 12 Attach the Mast Bracket Cover to the Mast Bracket Base by inserting at the hinge Place the Mast Bracket at the desired height on the mast Close the cover and secure the 2 1 2 bolt with the wing nut Do not over tighten See Fig 13 Fig 13 Skip to the Connecting the TV55 Antenna to a TV section to finish installation Connecting the TV55 to a TV GSAL 14 1 Run the RG6 coaxial cable from the antenna towards your television set and connect the RG6 coaxial cable to the supplied Power Injector on the terminal labeled TO ANTENNA 2 Connect the TO TV lead on the power injector to the ANT IN on your TV 3 Plug the Power Adapter from the Power Injector into a standard AC outlet Switch the Power Injector ON for amplification See Fig 14 Splitting the Signal to Multiple TV s e BD Follow the diagram to use the TV55 with more than one TV A splitter will be required sold separately NOTE The Power Injector MUST be installed between the TV55 and the splitter Failure to do so could cause d E N 2 a short circuit The Power Tork BSP_2 ae
12. port at 1 800 290 6650 Note THE POWER INJECTOR SHOULD NOT BE INSTALLED WHEN USING A SATELLITE SYSTEM WITH THE TV55 1 Disconnect the coaxial cable from your satellite dish s LNB 2 Reconnect this coaxial cable to the outdoor diplexer on the terminal labeled SAT ANT 3 Connect the RG6 coaxial cable downlead from the TV55 s F connector to an OUTDOOR diplexer port not included labeled ANT Connect the remaining coaxial cable from the LNB to the diplexer port labeled SAT The ports on all of the diplexers are F connectors 4 Disconnect the coaxial cable from your Satellite Receivers SAT IN Terminal and reconnect it to an Indoor Diplexer not included TV SAT 5 Connect an RG6 coaxial cable from the INDOOR diplexer port labeled SAT to the F connector port on the back of the satellite receiver labeled SAT IN Connect an RG6 coaxial cable from the INDOOR diplexer port labeled TV to the F connector port on the back of the satellite receiver labeled ANT IN 6 Connect an RG6 coaxial cable from the satellite receiver port labeled OUT TO TV to the F connector port at the back of the TV labeled ANT IN Note For assistance locating any antenna accessories not included with this product please call our Technical Support Department toll free at 1 800 290 6650 Monday through Friday 9 00AM to 5 00 PM EST or contact us at www audiovox com Trouble
13. tach the Channel Insert Brackets onto the channel insert bolt on the TV55 See Fig 8 Tighten with split washers and hex nuts Mounting the TV55 Antenna continued 7 Determine the location on the window where the TV55 will be mounted 8 Attach the Window Frame Brackets to the window Be sure the brackets are level and line up with the channel inserts already on the antenna GSAL 9 Insert the Channel Insert Brackets attached to the antenna into the slots on the Window Frame Brackets already mounted on the window Reattach the brackets with the screw removed earlier See Fig 9 i x A 10 Skip to the Connecting the TV55 Antenna to a TV section to finish installation 11 GSAL 12 Outdoors using Mast Mounting 1 Locate 1 Channel Insert 1 Mast Mount Base and Cover 1 1 1 2 hex head bolt 1 2 1 2 hex head bolt 1 Hex nut 1 Wing nut Insert both hex head bolts into the Channel Insert at the hex head recess Slide the Channel Insert into the channel on the back of the TV55 The bolts should be pointing away from the antenna See Fig 10 Fig 10 9 co Take the Mast Bracket Base and insert it over the bolts on the Channel Insert with the 1 1 2 bolt closest to the hinge Center the Mast Bracket on the TV55 Secure and tighten the 1 1 2 bolt with a hex nut Do not over tighten See Fig 11 Fig 11 Mou
Download Pdf Manuals
Related Search