Audiovox CDI-100R User's Manual
Contents
1. INSTALLATION GUIDE FOR SPECIAL PERFORMANCE SERIES Model CDI 100R ISO DIN MOUNT CD CHANGER CONTROLLER FM MODULATOR PARTS LIST Item Description Quantity 1 CDI 100 CDC Controller 1 2 M4 x 8P x 8mm 4 3 M5 x 8P x 8mm 4 4 ISO DIN Trim Ring 1 RADIO MAP POCKET DIS ASSEMBLY 1 Remove factory radio dash panel to expose sub dash 2 Remove radio map pocket assembly from the sub dash Retain the factory supplied mounting hardware 3 Disconnect the factory radio harness and antenna lead Loosen the radio mounting screws on one side of the radio map pocket assembly 4 Remove the pocket attached to the factory radio mounting bracket and discard as it will not be used in conjunction with the CDI 100R CDI 100R PREPARATION 1 Install the CDI 100R into the bracket assembly below the factory radio Make sure to align the CDI 100R face with the front of the factory radio Select the appropri ate size screws Item 2 or Item 3 from CDI 100R hardware bag to secure the CDI 100R to the factory radio bracket Secure the factory supplied radio mount ing screws See Fig 1 CAUTION Do not use longer screws or damage to the interior parts of the unit may occur 2 Plug the 8 pin circular DIN connector from the remotely mounted CD changer into the mating socket on the rear of the CDI 100R See Fig 2 3 Plug the cable from the vehicle antenna into the female antenna connector on the CDI 100R 4 Plug the male antenna conn2. OUND BLACK w WHITE STRIPE 12 VOLTS SWITCHED ORANGE w WHITE STRIPE TO 12 VOLTS CONSTANT ALA GREEN w WHITE STRIPE ANTENNA SOCKET L LOCATION AND TYPE WILL VARY MALE ANTENNA CONNECTOR 8 PIN DIN CONNECTOR FEMALE ANTENNA CONNECTOR FROM CD CHANGER FROM VEHICLE ANTENNA
3. ector from the CDI 100R into the antenna socket on the factory radio 5 Re connect the power speaker connector s to the factory radio 6 Connect the Green w White Stripe Orange w White Stripe and Black w White Stripe wires to constant 12 volts switched 12 volts and ground respectively as indicated in Fig 2 7 After completing the wiring in steps 2 through 5 perform a function test of the radio and CDI 100R to confirm correct operation ignition switch must be on during testing and adjustment Form No 128 5260 ADJUSTMENT OF FM OUTPUT FREQUENCY The output frequency of the CDI 100R is factory set to 89 1 MHz If there is interference from a local station on 89 1 MHz the output frequency of the CDI 100R can be changed to 88 7 MHz by sliding the switch the bottom of the chassis to the 88 7 MHz position ADJUSTMENT OF AUDIO LEVEL The audio level from the CDI 100R is factory set to provide the correct volume balance between radio and CD changer in the majority of installations and usually will not require any adjustment If however a large differ ence in volume level is noted when switching between CD changer and FM radio operation the audio level from the CD changer may be adjusted as follows 1 With the CD changer off tune to an FM station and adjust the volume control on the radio to a normal listening level 2 Leaving the volume control at the setting turn on the CD changer and tune the radio t
4. o the modulator output frequency 89 1 or 88 7 MHz 3 Select a LOUD section of the CD If the volume level is comparable to that of the FM station in step 1 no adjustment is necessary If it is noticeably louder or more quiet than that of the radio station use a 0 Phillips screwdriver to adjust the AUDIO LEVEL control on the bottom of the chassis so that the CD changer volume is comparable to that of the radio station IMPORTANT If the CDI 100R audio level is adjusted too high it may result in unacceptable levels of distor tion during loud sections of CD s If set too low it may result in poor signal noise levels during CD changer operation RADIO CDI 100R INSTALLATION 1 Dress the wires so there is no interference when installing the factory radio CDI 100R assembly into sub dash 2 Re install the factory radio CDI 100R bracket assem bly into the vehicle s sub dash utilizing the factory supplied mounting hardware previously removed 3 Replace the dash panel FACTORY RADIO CDI 100R ASSEMBLY FRONT VIEW FACTORY RADIO BRACKET TYPICAL FACTORY RADIO TYPICAL FACTORY SUPPLIED RADIO MOUNTING SCREWS ALIGN FRONT OF CDI 100R WITH FRONT OF FACTORY RADIO CDI 100R MOUNTING SCREWS ITEM 2 or 3 AUDIO LEVEL ADJUSTMENT ON BOTTOM OF CHASSIS FREQUENCY SWITCH ON BOTTOM OF CHASSIS FACTORY RADIO CDI 100R ASSEMBLY REAR VIEW FACTORY RADIO POWER SPEAKER CONNECTOR LOCATION AND TYPE WILL VARY GR
Download Pdf Manuals
Related Search