Audiovox CCDLF User's Manual
Contents
1. AUDIOVOX Y ELECTRONICS CORP Y Model CCDLF License Plate Rearview Camera with Non Reversed Image CCDLF FEATURES Built Into License Plate Frame High Resolution 1 3 CCD Color Camera Compact Zinc Alloy Die Cast Body Waterproof Housing Waterproof Microphone 150 Wide Angle View Non Reversed Image 128 7729 1 of 8 CONTENTS i ons QUANTITY LICENSE PLATE WITH NON REVERSED ee os CAMERA ANGLE ADJUSTMENT WEDGE THEFT THEFT PROOF SCREWS SCREWS FUSE 1A a CAMERAMOUNTING BOLT or DIELECTRIC GREASE PACKET 128 7729 2 of 8 Color Camera View Cable Hole A ou Camera to Frame Mounting Holes DC 12V R E 47 26 TH ES Y Grumet 128 7729 3 of 8 The CCDLF camera has a non reversed image This camera can be used with Audiovox LCD rear view mirrors and the LCM45NB It can also be used with multimedia systems that reverse the backup camera image Installation 1 Locate suitable location near the vehicles rear license plate to route the camera cable The camera cable can be routed through an existing grommet or use a location where a 5 8 hole can be drilled Be sure to check behind intended drilling location Check for camera interfer ence with license plate lights hatch release switch and or mechanism 2 Remove the screws holding the rear license plate to the vehicle and remove plate 3 Place the license plate into the camera license plate frame If routing camera cable into vehi2. and female terminals with the Dielectric grease supplied Slide the packaged pre sized heat shrink tube over both connectors and shrink using a heat gun to ensure a watertight connection View angle adjustment This camera frame is designed for universal application The angle of the image of the installed frame might have to be adjusted depending on the license plate mounting angle There is a 10 degree angle adjustment wedge supplied to change the downward angle from 40 degrees to either 30 or 50 degrees The angle wedge goes between the camera frame and camera body Longer camera mounting screws are provided for use with the angle wedge 1 Turn on monitor and look at back up camera image You should be able to see a small portion of the vehicles bumper 128 7729 5 of 8 2 If you see too much bumper the downward angle must be decreased Place the thin edge of the wedge on top between the camera and frame 3 If you cannot see the bumper at all the downward angle must be increased Place the thin edge of the wedge on the bottom between the camera and frame Camera Installation 1 LICENSE PLATE 2 CAMERA ANGLE ADJUSTMENT WEDGE 3 CAMERA 128 7729 6 of 8 Specifications Image Device 1 3 CCD with 10 Bit A D Digital Signal Processor Signal System CCDLF NTSC Standard image Total Effective Pixels NTSC 537 H 505 V Resolution Greater than 250 000 pixels Greater than 420 TV Lines Power source DC12V Video O
3. cle behind license plate drill a 5 8 inch hole at selected location Coat edge of hole with rust preventative Then route the camera cable connector through the hole and insert grom met into hole Place the license plate against vehicle and line up the mounting screw holes Using the black screws provide tighten the screws with the anti theft tool provided Pull gently on the camera cable to remove slack 4 If routing camera cable into vehicle above license plate remove license plate light valence Drill a 5 8 inch hole at selected location Coat edge of hole with rust preventative Then route the camera cable through the hole and insert grommet into hole Place the license plate against vehicle and line up the mounting screw holes Using the black screws provide tighten the screws with the anti theft tool provided Pull gently on the camera cable to remove slack 128 7729 4of8 If using Audiovox LCD rearview mirror or LCM45NB use the extension cable supplied with the monitor 5 Connect the Camera cable to the extension cable supplied Route the extension cable up to the intended monitor Connect as follows a Black wire connect to chassis ground b Red wire connect to 12V accessory wire c Yellow RCA connect to Video input d Red RCA connect to audio input if equipped When the connection of the Camera and Extension Cable is outside of the vehicle such as a Pickup Truck Application prior to making the connection coat the male
4. utput 1 0Vp p Composite 75 ohm load Low Lux Sensitivity 0 2 Lux S N Ratio More than 48db Current 80mA Operating Temperature 13 F to 158 F 25 C to 70 C Wide Angle View Diagonal 150 natural state lens declination 40 degrees Camera Outer Dimensions 25mm w x 30mm H x 62mm D Oo OMPNOaAAR WD gt ok _k mb N 7 128 7729 70f8 m o For Customer Service Msi Our Website Al WWW audiovox com roduct Information Photos FAQ s Owner s Manuals 2006 Audiovox Electronics Corp 150 Marcus Blvd Hauppauge N Y 11788 128 7729 128 7729 8 of 8
Download Pdf Manuals
Related Search