Audiovox ADV10A Installation Guide
Contents
1. the included wired switch If using the switch find a proper location for the switch to be mounted and then route the wire to the Nav Module Note The switch also allows switching through the AUX inputs if they are utilized DIP Switch Settings Up is OFF Down is ON for Dip Switches 12 Check the DIP Switch settings Dip 1 UP External RGB input Not Used Dip 2 UP Video Input 1 Off Dip 3 UP Video Input 2 Off Dip 4 DOWN High Resolution On for OEM Screen Dip 5 UP On for OEM Camera Off for after market camera Dip 6 UP Not used Dip 7 UP Up 8 screen Down for 4 screen Dip 8 UP Up 8 screen Down for 4 screen 13 Check to be sure the Map SD Card is installed in the Navigation unit Double check all connections and then reconnect the vehicle battery Navigation Interface Operation MyLink Intellink Equipped Vehicles To enter the Nav application from the touch screen press the location on the screen noted by the star for about 2 seconds This location will work in any screen or menu Exit Navigation by pressing the same location again NOTE When a call is received on Bluetooth the caller information is displayed on the driver information center above the steering column use the SWC controls to answer calls P m a D 3 E 3 PANDORA ETTINGS Mere md For Navigation operation see the included quick start guide or download a full user s manual from WWW ADVENTPRODUCTS COM If the pic2. MANDN ENT CADNAV1 Advent Integrated Navigation This interface is designed to integrate Navigation into select Chevrolet and GMC MyLink Systems This system is NOT applicable to vehicles that do not have CUE or MyLink Intelilink and will not operate in those vehicles GM GMC INSTALLATION GUIDE What s in the Box The following items are supplied with the CADNAV1 LVDS Video Cable 31414170 Aux Audio 31514170 CAN Module 33814170 GPS Antenna 34914170 CAD Power Harness 37514170 USB Update Cable 32714170 Prior to Installation Care must be taken when installing this accessory to ensure damage does not occur to the vehicle The installation of this accessory should follow approved guidelines to ensure a quality installation Read entire instructions thoroughly before starting This document covers such items as e Vehicle Protection use of covers and blankets cleaning chemicals etc e Vehicle Disassembly Reassembly panel removal part storage etc Electrical Component Disassembly Reassembly battery disconnection connector removal etc NOTES Removed Parts Inspect the vehicle for any damage Place all removed parts on a protected surface in an area where they will not be damaged Connectors When disconnecting connectors do not pull on the wires pull on the connectors Vehicle Preparation and Protection CAUTION e Do not touch the positive terminal with any tool when removing cable e Be sur
3. e ignition key is in the OFF position during install e Donot disconnect ANY airbag connectors or indicators Doing so may result in activating a diagnostic code These codes will require the dealer to perform the reset procedure and may be charged a dealer fee e Ifyou are unsure of any vehicle trim removal process consult the OEM service manual e Removing vehicle trim panels in extreme hot and cold climate could result in some vehicle damage Use care when removing all vehicle trim e Using tape on vehicle trim panels could help limit any scratches and or marring Use plastic trim panel removal tools whenever possible The instructions included in this kit are current at the time of printing It is designed as a guide to help make the installation of this product successful Always use caution and ask for assistance if you are not sure how to proceed Voxx International is not responsible for any damage that may occur during installation or any changes to the vehicle interior Installation Steps 1 IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION TO AVOID DAM AGE TO THE RADIO AND UNINTENDED AIR BAG DEPLOYMENT 2 USE A TRIM TOOL TO DISENGAGE CLIPS AND REMOVE TRIM PANEL SURROUNDING RADIO DISPLAY ASSEMBLY 3 REMOVE 4 SCREWS FROM RADIO DISPLAY ASSEMBLY 4 DISCONNECT 10 PIN CONNECTOR AND MICRO USB CONNECTOR FROM RADIO DISPLAY MONITOR 1 The navigation module can be locat
4. ed behind under or to either side of the radio depending on space available Determine your exact mounting location to insure you route your wires correctly 2 Using the supplied T harness power cable disconnect the matching cable from the rear of the main radio unit Plug the T harness in the radio and the factory harness into the T harness Yellow arrow 3 Plug the supplied LVDS cable in to the radio screen and the factory cable into the LVDS t harness cable from the nav unit Connect the LVDS cable to the Nav module Cadillac CUE system Shown above NOTE The Buick GMC radio panel will look different than the picture above but the connections are the same 4 Connectthe CAN module to the power harness connection 5 Connect the CAN to Nav interface cable to the main Nav module as shown in the wiring diagram 6 The system utilizes either the center front speaker in the dash or an included external speaker for easier installation or for vehicles that do not have a center channel speaker The Nav system will mute the radio audio in that speaker only when giving directions NOTE The left dash speaker will also work if no center speaker is available To install using the factory speaker remove the center channel speaker from the dash route the included speaker harness to the speaker location Connect the supplied harness to the speaker and the OEM wiring to the other harness connector Route the wire to the module and connect If
5. itional control Maximum current of 2A port 1 2 7 10 ee temperature range 40 404850 11 Dimensions 15 6 X9 2X22Cm For Technical Support Please Call 1 800 323 4815 W GPS Antenna i AUX audio out LVDS Cable EI ET Navigation Interface i ACC OE Spkr or Ext Spkr Deen eee eee BATT E Ctrl Ga 4 GHD ta 5 Reverse l gw Daia _ we From 1 i CAM fax Fa 1 Ta See Pee eee massa DILLO zd DIP Settings AUX Video ti Y c acasa tit Power from CAN box Connect to CAN box Power Harness for Chrysler Vehicle Specific Instructions Tech Tips and Installation notes can be found at WWW AUDIOVOXUNIVERSITY COM NDV ENT Voxx Electronics Corporation Hauppauge NY 11788 Technical Assistance 1 800 323 4815 WWW ADVENTPRODUCTS COM O 2015 Printed in China 128 9394
6. ture is not centered or does not fill the screen correctly you can adjust the picture size Access the settings menu by pressing the Menu button on the side of the Nav Interface Module Use the Menu button to scroll through the options and or buttons to adjust the value Contrast Brightness and Saturation are all screen adjustments for picture quality Position H and V are for Horizontal and Vertical Position use to adjust to fit factory screen as needed IR AV1 IR AV2 NOT USED Select NONE to insure proper operation Guide L Guide R CNTRL These are controls for the position of the Parking Lines By selecting or you can move the position of the lines to match the vehicle width 5 H Size V Size This will adjust the picture to meet the full screen size of the OEM panel pM Setup Menu Contrast Brightness Saturation Position H Position V NOT USED NOT USED Guide eee ee 0 Guide R Guide CNTRL Specifications No Name Parameters O Videoinput 07Vppwith 75 Q impedance 2 Synchronized signal strength 3 5Vpp with 5K impedance negative pulse synchronization RGB resolution By changing DIP4 user can select HD VGA or normal HD 800X480 or VGA 640X480 Normal NTSC vertical 240 or 234 Av1 Av2 cam video 0 7Vpp with 75 O impedance Av1 Av2 cam format NTSC PAL SECAM Automatic switch s em pwe ET Trigger level threshold Reverse and gt 5V trigger switching Output current of add
7. using the included External speaker pick a location that is not obstructed and can be heard easily by the driver Remove the tape backing from the rear of the speaker and attach to the mounting location Route the wire to the module and connect e f needed or for custom installation this can be wired to any standard 4 ohm speaker The Green and Gray colored wires are the audio output The Nav module has the ability to add a backup camera and 2 AV inputs The module will support the factory backup camera if the vehicle is equipped with this If you are adding a camera or aux inputs use the supplied cables and connect as needed 7 AuxVideo 8 Aux Video Aux Audio Red Backup Camera Input See attached labels Yellow Aux 1 Video Input White Aux 2 Video Input Gray Not used 9 USB Update Cable This is used for map updates Route the cable from the module to the glove box for future use as needed Connect to the Nav module 10 GPS Antenna The antenna must be mounted in a location where it has a clear view of the sky Center of the dash by the glass is recommended NOTE f reception is poor re locate to another area and re test The GPS antenna cannot be blocked by metal surfaces and should be visible for best reception 11 Nav activation switch In Cadillac vehicles with CUE the nav is activated by pressing the NAV icon on screen In other vehicles the nav will be activated by pressing a set position on the screen or using
Download Pdf Manuals
Related Search