Audiovox 50-0246x-015 Series User's Manual
Contents
1. at rear of console See Figure 1 FIGURE 1 2 Disconnect wiring harness from console See Fig 2 Lay console in a safe place Remove and retain 2 two O E M screws from plastic bracket Transfer Velcro tape from console to identical location on new console item 4 pg 2 FIGURE 2 3 Carefully trim headliner and return air grille as shown Make sure that the 7 cut is centered left to right in vehicle See Figure 3 Caution Before cutting headliner material check for wiring or other componentry above headliner Cut only where indicated FIGURE 3 4 Install mounting bracket item 6 pg 2 and secure using 2 two 10 x 3 4 screws item 1 pg 2 in bottom flange that aligns with dimples in roof brace Secure top flanges using 2 two 8 x 3 4 screws item 3 pg 2 See Figure 4 FIGURE 4 HI INSTALLATION OF CONSOLE NOTE Additional assistance in mounting the overhead console in vehicle is advised to prevent damage to console or components 5 Install and route all accessory wiring video and audio cables and any other added component requirements to their respective places in the vehicle Refer to component installation instructions for wiring diagrams The suggested routing of the video system cable is as follows Above the headliner from video system to B pillar Down the B pillar to the floor Route the power lead to an accessory controlled source Connect the ground lead to the vehicle chassis Route2. the remaining wiring RCA plugs Remote Sensor extension etc to the VCP location See Figure 5 Connect per instructions included with video system If video system is to be used as a television install an appropriate antenna per instructions included with antenna O E M 6 Using the diagram in Figure 6 construct a jumper pe CONNECTOR harness that will connect the vehicle s dome light ee wire harness to the new dome lights in video TO POWER system Make sure that lights in video system operate from the door jamb switch YELLOW i TO HE LIGHT SWIA FIGURE 6 7 Carefully position console against headliner Make sure O E M wire harness routes through opening in console Loosely install using 2 6 32 X 3 4 screws item 4 pg 2 through the smaller holes in bracket on console into threaded clips on mounting bracket Using an awl or similar tool align the front mounting holes in console with holes in bracket Loosely secure using 2 two 8 x 3 4 O E M screws previously removed See Fig 7 Make sure console alignment is straight the tighten all screws Note Do not overtighten screws FIGURE 7 Caution Do not overtighten screws Use extra support for the console until secured to the vehicle Failure to do so may cause damage to console or installed components 5 8 Release video screen from locked position Lower video screen to viewing position for access to mounting lo
3. INSTALLATION INSTRUCTIONS FOR 50 0246x 015 SERIES 1181270 1999 DODGE DURANGO OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 Razor knife or similar 4 1 4 hex socket bit 5 Awl or similar tool 6 5 16 hex socket bit 7 Audiovox Series 640 650 Video Module FOR USE IN VEHICLES EQUIPPED WITH FACTORY INSTALLED REAR AIR CONDITIONING and WITH FACTORY OVERHEAD CONSOLE ONLY May 19 1999 INSTALLATION INSTRUCTION 44 0024B Printed in the U S A MATERIALS PROVIDED FOR INSTALLATION ITEM Description QTY SCREW 8 X 3 4 HWH SCREW 8 X 11 4 PPH SCREW 10 X 3 4 HWH SCREW 6 32 X 3 4 PPH WASHER 3 5 mm MOUNTING BRACKET CONSOLE NSA Mh HN ere FON KF NY May 19 1999 INSTALLATION INSTRUCTION 44 OF VEHICLE INTERIOR Printed in the U S A 1 Remove and discard front mounting screw from overhead console and pull downward to release clips
4. cations in top of video system housing 9 Raise video system into approximate position and connect all wiring to components Route video cable through notch in mounting bracket Connect wiring and cabling to video system per instructions included with video system 10 Check function of all components and lights See operating instructions for video system operations check For further assistance refer to the video system manual for the technical support phone number listed for your area Insert video system into opening in console Note Make sure that wires do not get pinched between bosses on video system and console Align holes in housing with clips in mounting bracket See Figure 8 Secure using 4 four 6 32 X 3 4 screws item 4 pg 2 and 4 four 3 5 mm washers item 5 pg 2 Caution Do not overtighten screws FIGURE 8 12 Raise video screen into locked position 1 _ 13 Carefully remove 2 two spring clips from rear of O E M console and insert in slots in bracket on console previously installed See Figure 9 14 Connect wire ha HSY RF E M console and install in original position Secure front of console using 1 one 8 x 1 1 4 screw item 2 pg 2 Caution Do not overtighten screws Make sure clips at rear of console are snapped firmly into tabs on O E M console See Figure 10 FIGURE 10
Download Pdf Manuals
Related Search