Aube Technologies TH140-28 User's Manual
Contents
1. Select the span using switches 1 and 2 The default temperature span is 0 5 C 0 9 F For example if the temperature setpoint is 20 C 68 F the heating system will turn on at 19 5 C 67 1 F and turn off at 20 5 C 68 9 F Span Hot Water Heating Forced Air Heating Not recommended for Not recommended for furnaces central units Radiant or convection electric heating Gas or electric wall furnace Fuel or gas floor furnace Central heating Commercial unit 1 240 volt heating with relay baseboard convector radiant ceiling etc 400 140 000 C 2008 01 15 2 4 1 5 Install the Batteries When you first install the batteries the unit runs a sequence of tests and a complete reset to zero The screen should display 0 00 MO and the ambient tem perature The current setpoint is 20 C cI ma c3 5 MI Sd s n The ambient temperature could be higher if you are holding the TH140 in your hands It will return to normal about one hour after installation 1 5 1 Replacing the batteries The TH140 will display an icon indicating that the batteries must be replaced This icon will be displayed for 60 days after this delay the 7 TH140 will shut down the heating unit BaT jo The time and programming are saved for 15 seconds when replacing the batteries Basic Configuration Note You may program the thermostat while holding it2. the next program To bypass e Set the desired temperature AW OR quickly press xX or to use a pre defined setpoint 3 2 Manual 4 This mode allows you to maintain a constant temperature To activate this mode tae e Press Manual Auto until is displayed ces e Set temperature AW OR quickly press x or to use a pre defined setpoint 3 3 Vacation o gt Maintains a specific temperature when away for a pro longed absence e g vacation cu e From the TH140 quickly press gp to activate ibe e Can also be activated remotely CT240 home automa tion system or any other system if the remote input is connected to one of these systems Note When the Vacation mode is activated remotely it can only be deactivated remotely Note For details on how to activate the Vacation mode using a tele phone refer to the CT240 Instruction Manual Program Your Schedule The TH140 allows four setting changes for each day of the week There are no pre set programs Your heating system switches betw wen the Comfort setpoint and the Economy setpoint according to the times you would have set For example enter each day the time at which you wake up PROG 1 the time you leave for work PROG 2 the time you return home PROG 3 and the time you go to bed PROG 4 PROG 1 Note For temperature increases PROG 1 and 3 allow at least 15 minutes per 1T 2 For example if you have l
3. Protection class Il Protection degree IP 40 The terminals are designed to handle a cross section of wire measur ing up to 2 5 mm 14 AWG V Warranty Aube warrants this product excluding battery if applicable to be free from defects in the workmanship or materials under normal use and service for a period of three 3 years from the date of purchase by the consumer If at any time during the warranty period the product is determined to be defective or malfunctions Aube shall repair or replace it at Aube s option If the product is defective i return it with a bill of sale or other dated proof of purchase to the place from which you purchased it or ii contact Aube Aube will make the determination whether the product should be returned or whether a replacement product can be sent to you This warranty does not cover removal or reinstallation costs This warranty shall not apply if it is shown by Aube that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer Aube s sole responsibility shall be to repair or replace the product within the terms stated above AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESS OR IMPLIED OR ANY OTHER FAILURE OF THIS PRODUCT Some provinces and states do not allow the exclusion or limitation of inc
4. SU Set the time 6 00 for the first program PROG 1 using the Hour and Minute buttons Press Program to select PROG 2 Set the time 8 30 using the Hour and Minute buttons Press Program to select PROG 3 Set the time 4 00 p m using the Hour and Minute buttons Press Program to select PROG 4 Set the time 11 00 p m using the Hour and Minute buttons Press Manual Auto to exit O 8 O To erase programs 2 and 3 for Saturday and Sunday Press Program to access programming mode Press Program until PROG 2 is selected Press Day to select SAturday SA Press Clear to erase the time Press Day to select SUnday SU Press Clear to erase the time Repeat steps 2 to 5 for PROG 3 Press Manual Auto to exit Oo90000080 0 TH140 28 Technical Specifications Power supply 2 AA or LR6 alkaline batteries 1 5 V Max resistive load 5 A 240 VAC 5 A 30 VDC Max inductive load 2 A 240 VAC 2 A 30 VDC P F 0 4 Remote input 12 VDC 10 2 5 mA Certifications CE c UL us Control device Electronic Automatic action Type 1 B Number of programs 4 programs day total of 28 programs Storage temperature 20 C to 50 C 4 F to 122 F Operating temperature 0 C to 50 C 32 F to 122 F 95 R H Temperature setting range 5 C to 30 C 40 F to 85 F Temperature display resolution 0 1 degree Temperature reading accuracy 0 5 C 0 9 F Software Class A
5. aube technologies Installation 1 1 Guidelines TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK Installation should be carried out by an electrician e For a new installation choose a location about 5 ft 1 5 m above the floor e The thermostat must be installed facing the heating system and on an inside wall e Avoid locations where there are air drafts top of staircase air out let dead air spots behind a door direct sunlight or concealed chimneys or stove pipes Loosen the captive screw holding the faceplate to the mounting plate Pull the lower part of the faceplate to remove it from the mount ing plate 0 Loosen the screw captive holding the wire cover and remove the wire cover Pull wires through the hole in the mounting plate and secure the mounting plate to the wall or onto an electrical box for line volt age wiring using the enclosed wall anchors and screws Wire the thermostat to the heating system see section 1 2 and if necessary connect the remote input see section 1 3 Once wiring is complete re install the wire cover Use the switches located at the back of the faceplate to config ure your thermostat see section 1 4 according to your applica tion Install the batteries see section 1 5 Mount the faceplate on the mounting plate and tighten the screw TH140 28 TH140 28 Installation and User Guide Electr
6. idental or consequential damages so this limitation may not apply to you THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE WAR RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS WARRANTY Some provinces and states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from province or state to another 2A Technical Assistance ba E 705 Montrichard 10 rue Amp re Saint Jean sur Richelieu 95500 Gonesse Qu bec Canada J2X 5K8 France Tel 450 358 4600 33 0 1 34 07 99 00 1 800 831 AUBE 33 0 1 3407 99 19 Fax 450 358 4650 advaube comintes com aube service honeywell com eh t For more information on our products visit us at www aubetech com 400 140 000 C 2008 01 15 4 4
7. in your hands or when it is mounted on the mounting plate 2 1 Setthe Time and Day Set the time using the Hour and Minute buttons Set the day using the Day button 2 2 Configure the Setpoints 2 2 1 Comfort and Economy These setpoints are associated to the schedule s programs and are pre programmed as follows Comfort 20 C 68 F Programs 1 and 3 Economy q 18 C 64 F Programs 2 and 4 2 2 2 Vacation This pre programmed setpoint is used when the Vacation mode is activated Vacation CD 2 2 3 To Modify a Setpoint Set the temperature using A V 10 C 50 F ae co cS Press and hold one of the setpoint z buttons X or or until the ty gt A p icon is displayed on the screen approx 3 seconds mu MJ ke4 2 3 View the Current Setpoint To view the current setpoint quickly press once one of the arrow buttons A V co mu co oO a Mm TI The screen displays the setpoint the arrow 4 indicates a setpoint my rola Ne TH140 28 Select the Operating Mode The TH140 offers three operating modes 3 1 Automatic This mode executes the schedule To activate Press Manual Auto until is displayed The program setpoint icon is displayed x 3 1 1 Temporary Bypass When in Automatic mode you can temporarily bypass the current program setpoint until the beginning of
8. l automatically switch from normal operating mode to Vacation mode or vice versa when the sig nal is removed 1 3 1 Connection to the CT240 Connect CT240 terminals A and C to TH140 terminals X and C You must respect the polarity For details on operating the telephone control ler refer to the instruction manual 1 3 2 Connection to a home automation system Connect the TH140 to the home auto TH140 mation system as displayed in the wir o ing diagram ee 1 4 Configure the Thermostat The switches are located on the back of the faceplate Default set tings are highlighted CO 0 5 C 0 9 F see 1 4 2 Temperature display Teroernure conrdimode aa p see 1 4 1 see 1 4 2 1 you change from C to F or vice versa you will need to reprogram your Comfort Economy and Vacation settings 2 For hot water installations it is recommended to enable this option to acti vate the pump for one minute every 24 hours to prevent pump seizure 1 4 1 Proportional Adaptive Mode switch 5 This mode analyzes previous cycles to define the the next duty cycle This control mode guarantees optimal temperature control based on the system s capacity To extend the life of the system a minimum On Off time of 10 of the cycle has been implemented For example with a 15 minute cycle the system would not start or stop for less than 1 5 minutes Ideal for e Radia
9. nt or convection electrical heating system e Circulator control in a hot water system e Electrical hot air furnace e Conventional gas or fuel hot air furnace Not recommended for e Gas or fuel furnace or boiler with a wall chimney having a 30 sec ond or higher combustion gas purging cycle To figure out the gas purging cycle of your system count the time between the heating command sent by the thermostat and the moment when the burner actually goes on e Multi zone systems where several thermostats command a single heating unit Note In these last two cases conventional mode with anticipation is recommended TH140 28 Heating Cycle Selection switches 1 and 2 Select the cycle using switches 1 and 2 Short cycles help eliminate temperature variations thus increasing user comfort Since shorter cycles can lead to premature system wear it is important to select the temperature control cycles appropriate to your heating system In general the bigger your heating unit is the longer the cycles should be Not recommended for Not recommended for 5 minutes furnaces central units 10 minutes Radiant or convection electric heating Gas or electric wall furnace Central heating Fuel or gas floor 15 minutes furnace forced air heating 1 4 2 Conventional mode with anticipation switch 5 This mode is compatible with all heating systems Commercial unit Programmable Span Selection switches 1 and 2
10. onic Programmable Thermostat 1 2 Thermostat Wiring NORTH AMERICA LOW VOLTAGE lt 30 V no polarity Q A 120 240 V Connection to a i circulator through Relay a 24 V relay Y 1 ANN I ia ie 24 V transformer 3 Connection to the thermostat terminals of a furnace Furnace LINE VOLTAGE 120 to 240 VAC Must be installed onto a certified electrical box 2 A maximum load Power supply I taal Y 120 240 V 3 Connection to a circulator pump of a water heating system For a 2 wire connection no polarity _ K N i 4 240 V eH V CIN Provided wires Direct wiring to the circulator 3 O OS L 1 I m melay Connection to the a z Ta thermostat terminals 3 J2 of a furnace Furnace For a 3 wire connection observe the polarity I Wiring to a power operated mixing control valve z ooo N 0 240 V L 400 140 000 C 2008 01 15 1 4 1 3 Remote Input Wiring The TH140 is equipped with a remote input which allows connection of a telephone controller optional Aube CT240 a home automation system or any other remote control system When a signal is received through this input the TH140 wil
11. owered the temperature by 3 6 F while you sleep and you wake up at 7 a m change the setting at 6 15 a m Comfort PROG 2 Economy 30 Comfort Economy 400 140 000 C 2008 01 15 3 4 4 1 Set or Modify the Programs e After 60 seconds of inactivity the thermostat will automatically exit programming mode e It is sometimes faster to program the same schedule for the entire week and then modify the exception days Press Program The screen displays MO and PROG 1 Press Day to select the day hold for 3 seconds to select all days of the week Press Hour and Minute to set the start time To clear an entry press Clear the time zone displays when the program is inactive Press Program to select the program number 2 3 or 4 Repeat steps 3 and 4 for remaining programs Press Manual Auto to exit 4 1 1 Programming Example z Comfort programs 1 and 3 e Monday to Friday between 6 00 a m and 8 30 a m and between 4 00 p m and 11 00 p m e Saturday and Sunday between 6 00 a m and 11 00 p m Economy programs 2 and 4 e Monday to Friday between 8 30 a m and 4 00 p m and between 11 00 p m and 6 00 a m e Saturday and Sunday between 11 00 p m and 6 00 a m BOOLE a o erojen 1100 enoo enoo 00 To program this schedule Press Program The screen displays MO and PROG 1 Press and hold Day for 3 seconds to select all days of the week MOTUWETHFRSA
Download Pdf Manuals
Related Search