Aube Technologies TH115 User's Manual
Contents
1. TH115 A F AF Owner s Guide aube technologies Thank you for choosing the Aube TH115 a programmable thermostat that provides both energy savings and comfort O ill D 2 ooo 5 OO a D nN o g O O First Power ON When power is applied for the first time the LCD displays 0 00 MO Monday 4 and temperature room floor Press HOUR MIN to set the current time Press DAY to set current day For AF and F models one of the two following messages may be displayed if the installation is incorrect LO The floor temperature is below 32 F 0 C or the temperature sensor is defective or not con nected The heating indicator is dis played and the relay is closed energized The floor temperature is above 140 F 60 C or the tempera ture sensor is defective Incorrect ae TH115 Description Buttons and symbols On Stand By Switch Use this switch to put the thermostat in sleep mode when its use is no longer required e g summer This will not affect the clock or programming GFCI Warning Light and Test Button Day amp Clock Settings Programming Mode Mode Selection Exit Programming Room OR Floor Temperature Current Mode and Setpoint Current Program Number Setpoint definition Pre defined Setpoints G00000000 Increase Decrease Temperature Models A Controls the Ambient t2. age wires back into the electrical box Secure the power base to the electrical box using the provided screws If necessary set the configuration switches on the control module refer to the control module user guide Install the control module onto the base OO 890 Apply power to heating system PB112 Figure 1 Figure 2 on ite SENSOR N Technical Specifications Woas Supp wax twa Power vanna oF 240 VAC 50 60Hz 3600 W 240GA 508 VAC 50 60Hz 3120 w AW DP ar 240 VAC 50 60Hz 3600 W 240GB 208 VAC 50 60Hz 3120 w AW DP 240 VAC 50 60Hz 4000 W 240S 208 VAC 50 60Hz 16 7A 3475 w 4WISP a 240 VAC 50 60Hz 3600 W 240D 208 VAC 50 60Hz Oa 3120 w 4WDP m Storage 4 F to 120 F 20 C to 50 C Remote controller input ECONO requires a dry contact Size H W D 4 89 x 2 76 x 0 91 in 124 x 70 x 23 mm Models Models Certifications GF 120 GA GB Gi 120S 240S c US 240 GA GB i US LISTED 240D 400 112 006 B 1 6 05 1 1
3. ank grid to record your new schedule PaE et ITT rele S T S a S A eaf T ere EEE Model JA CIF OAF Temperature display O F LJ c Time display LJ 12hrs LJ 24hrs Warranty AUBE TECHNOLOGIES INC ONE 1 YEAR LIMITED WARRANTY This product is guaranteed against workmanship defects for a one year period following the initial date of purchase During this period AUBE Technologies Inc will repair or replace at our option and without charge any defective product which has been used under normal conditions The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation This warranty cancels and replaces any other manufacturer s express or implied warranty as well as any other company commitment AUBE Technologies Inc cannot be held liable for related or random damages following the installation of this product The defective product as well as the purchase invoice must be returned to the place of purchase or mailed prepaid and insured to the following address Aube Technologies Inc 705 Montrichard Saint Jean sur Richelieu Quebec Canada J2X 5K8 O Remote Input The TH115 is equipped with a remote input which allows connection of a telephone controller accessory Aube CT240 or any other remote control system When a signal is received through this input the TH115 will automatically switch from normal operating mode to Vacation mode a
4. ar of the control module To modify any setting switch UP or DN QO Temperature Setpoint The following temperature setpoints are pre programmed AIAF F Comfort when at home 50 F Economy when asleep away from home prolonged absence To modify a setpoint Setthe desired temperature using av Press and Hold the x or or button until symbol is displayed Press RET to exit Floor temperature limit The floor temperature limit is 82 F To modify this limit Press X and hold while switching from ON to Stand By then back to On Set temperature aw Press RET to exit To avoid damaging your floor we recommend you _ follow the supplier s instructions Control Module Installation Align the bracket tabs on the control module with the holes located on top of the power base Control module NOTE Keep the thermostat s air vents clean and free from obstructions Power base NOTE The screw cannot be removed completely Operating Modes Automatic Executes the schedule Press MODE until is displayed The cur rent program number is displayed You can temporary bypass the current pro gram by setting a specific temperature av or by pressing on a pre defined setpoint button amp q The new setpoint will be maintained until the begin ning of the next program Manual Maintains a constant temperature Press MODE unti
5. eek and then to modify the exception days To modify Press PGM to access the programming mode Press DAY to select the day to be programmed hold for 3 seconds to select all days of the week Press PGM to select the program number Press HOUR and MIN to set the time or press CLEAR to clear the time is disregarded Repeat steps 2 to 4 for remaining programs When completed press RET to exit mode NOTE After 60 seconds of inactivity the thermostat will automatically exit programming mode Technical Specifications Model TH115 A AF F Display range 32 F to 140 F 0 C to 60 C Setting range ambient 40 F to 86 F 5 C to 30 C Setting range floor limit 40 F to 104 F 5 C to 40 C Pre programmed temperature setpoints Comfort A AF 70 F 21 C and F 82 F 28 C Economy A AF 64 F 18 C and F 68 F 20 C Vacation A F AF 50 F 10 C Floor limit AF 82 F 28 C Accuracy 0 9 F 0 5 C Storage 4 F to 120 F 20 C to 50 C Temperature control Proportional integral adaptive 15 minute or 15 second heating cycles according to the application and power base gt gt gt gt Memory backup In the event of a power failure an internal circuit will maintain the programming Only the time will have to be set if the power failure is more than two 2 hours The thermostat will return to the same operating mode as set before the power failure Custom Grid Use this bl
6. emperature AF Controls the Ambient temperature and Floor temper ature limit F Controls the Floor temperature O GFCI Test GA amp GB power base only The GFCI monitors the electrical flow for any loss of current if there is one the thermostat will cut off power to the heating system We recommend you test the GFCI immediately after installing the control module and once a month thereafter to ensure it is operating properly To test Increase the temperature A until the heating indicator is displayed Press TEST A e Successful the TEST warning light is ON and power to heating system is cut off e Unsucessful the TEST warning light is OFF Cut E gt power to heating system from the main power panel and call customer service When successful reset thermostat Stand By On to power the heating system NOTE If the test warning light comes ON during normal operation cut power to heating system from the main power panel and have an electrician verify the installation 2 Switch Selection This thermostat is factory set to the following values If you switch from F to C or vice versa the X and setpoints may need to be redefined When using AUTO mode the thermostat calculates the optimum start time to obtain the desired temperature by the set time The heating system could be started a few hours prior to set time when required Switches are located on the re
7. l is displayed Set temperature av or press x touse w pre defined setpoint Vacation n Maintains the Vacation setpoint during a prolonged absence gt Press D until the icon is displayed 920 115 007 00 1 A 8 Pre programmed Schedule The TH115 programmable thermostat is pre programmed with the following schedule Time you wake up and desired temperature Time you leave and temperature during your absence ogane Mo TU eet ER ee oe E el eee ee ee ee Freee 0 0 a0 eS eee ra o pojenja Temperature Control Time you return home and desired temperature Time you go to bed and overnight temperature The TH115 thermostat works differently than conventional electromechanical thermostats It is equipped with a proportional integral adaptive P 1 A controller which determines heating cycles by analyzing the temperature behavior history within the room The P I A controller reduces temperature variations providing an accurate temperature control while increasing user comfort The controller determines the amount of power required by the heating system to maintain the setpoint temperature 1 to 20 21 to 40 41 to 60 61 to 80 81 to 100 Modify the Schedule Notes gt You can program up to 4 different programs per day Each day can have different programs gt It is sometimes faster to program the same schedule for the entire w
8. nd vice versa when the signal is removed Activating the Vacation mode D There are two ways to activate the Vacation mode From the thermostat see Operating Modes above Froma telephone remote location For details on how to activate using a telephone refer to the CT240 Instruction Manual WARNING When the Vacation mode is activated remotely it must be deactivated remotely If you have any questions concerning the installation or programming of the TH115 programmable thermostat call our technical support team at Phone Montreal area 450 358 4600 Canada U S 1 800 831 AUBE 2823 Fax 450 358 4650 Email service aubetech com Monday to Friday from 8 30 AM to 5 00 PM EST For more information on our products visit us at www aubetech com As an ENERGY STAR partner Aube Technologies has determined that this product meets the ENERGY STAR guidelines for energy efficiency 04 08 2003 920 115 007 00 1 A technologies ab PB112 Installation Instructions For models 120GA 120GB 120S 240GA 240GB 2408 240D Parts one 1 power base Two 2 screws Four 4 solderless connectors for copper wires NOTE Special CO ALR solderless connectors must be used for connecting aluminum conductors one 1 floor sensor and one 1 flat tip screwdriver F and AF floor heating models only Guidelines Turn off power to the heating system at the main elect
9. rical panel to avoid electrical shock The installation should be carried out by an elec trician gt High voltage thermostats must be installed onto an electrical box gt For a new installation choose a location about 5 ft above the floor and on an inside wall gt The thermostat must be installed on an inside wall facing the heating system except for floor heating systems gt Avoid locations where there are air drafts top of staircase air outlet dead air spots behind a door direct sunlight or concealed chimneys or stove pipes except for floor heating systems Procedure Connect the power base wires to the power supply and load using sold erless connectors for copper wires figure 1 if your thermostat is type F or AF not A insert the floor sensor wires through one of the two holes below the terminals figure 2 and connect the wires to terminals 3 and 4 no polarity The wires must run alongside the terminals and not go over them The wire must not cross any heating wires nor be placed directly on a heating wire or adjacent to it For best performance the sensor probe should be centered between the wires in the mat i you wish to use a remote controller such as the CT240 or CT241 insert the cable use 18 to 22 gauge flexible wires into one of the two holes available below the terminal board and connect to terminals 1 and 2 of the base figure 2 Push the excess length of the high volt
Download Pdf Manuals
Related Search