Aube Technologies TH113-R User's Manual
Contents
1. Phone Montreal area 450 358 4600 Canada U S 1 800 831 AUBE 2823 Fax 450 358 4650 Email service aubetech com Monday to Friday from 8 30 AM to 5 00 PM EST For more information on our products visit us at www aubetech com 05 11 03 400 113 004 A d technologies Applications The PB112 024T 15S power base can be used on any TH11x series thermostat with the exception of the TH110 model This low voltage power base operates on 15 second cycles and can be connected to a line voltage load using a solid state relay The PB112 024T 15S is compatible with most solid state relays however the following Aube relays are optimized for use with this power base RT850 solid state relay SSR e RT850T solid state relay SSR with built in 24 V transformer WARNING This power base MUST be used ONLY with solid state relays The use of electromechanical relays will result in reduced life expect ancy and in the possibility of overheating of these devices Supplied Parts One 1 power base Two 2 plastic anchors Two 2 mounting screws Installation Guidelines gt For a new installation choose a location about 1 5 m 5 ft above the floor gt The thermostat must be installed on an inside wall facing the heating system except for floor heating systems gt Avoid locations where there are air drafts top of staircase air outlet dead air spots behind a door direct sun2. switch making it possible to put it in sleep mode when its use is not required e g summer IMPORTANT The GFCI and Remote Input options are not available with a low voltage power base Skip sections 3 and 4 4 Remote Input line voltage only When a remote control interface Aube CT241 or any other remote control system is connected to the power base s remote input and a signal is received the TH113 R module automatically lowers the percentage by 35 based on the dial s current position The LED lights up to indicate the signal s presence except for GA and GB models Signal temporary bypass The TEST button can be used to bypass the signal for a 2 hour period The LED goes off to indicate the bypass NOTE When combined with a GA or GB power base the TEST button is used only for GFCI testing The percentage is decreased but the bypass function and indicator are not available Control Module Installation Align the bracket tabs on the regulator with the holes located on the power base Control Module Power Base This regulator must be installed on a PB112 power base The screw cannot be removed completely Keep the regulators air vents clean and free from obstructions Technical Specifications Model TH113 R Power setting range 0 to 100 Storage 20 C to 50 C 4 F to 120 F Warranty AUBE TECHNOLOGIES WARRANTY This product is guara
3. 24 V vac Transformer a Peer ees COM VDC vac OQ EEEE EE COM Heater RT850 Technical Specifications Maximum load 0 5 A 24 VAC Heating cycle length 15 seconds Operating temperature 32 F to 122 F 0 C to 50 C Storage 4 F to 122 F 20 C to 50 C Size H W D 124 x 70 x 23 mm 4 89 x 2 76 x 0 91 in Wire gauge 14 to 22 AWG 400 112 024 A 18 1 06 1 1
4. TH113 R Regulator User Guide wae technologies GFCI Test and Warning Light On StandBy Switch Power Selection Dial GFCI Test GA GB line power base only The GFCI monitors the electrical flow for any loss of current if there is any loss the thermostat will cut off power to the heating system We recommend you test the GFCI immediately after installing the control module and once a month thereafter to ensure it is operating properly To test Press the TEST button Successful TEST warning light is ON and power to heating system is cut off Unsuccessful TEST warning light is OFF Cut power to heating system from the main power panel and call customer service When successful reset thermostat STANDBY ON to power heating system NOTE If the test warning light comes ON during normal operation cut power to heating system from the main power panel and have an electrician verify the installation Introduction Thank you for choosing Aube s TH113 R Regulator The TH113 R is specially designed to control a floor heating installation a baseboard or a convector The TH113 R regulator operates like a dimmer switch to allow you to easily adjust the amount of power sent to your heating system It features an integrated GFCI and includes a test button and warning light for added security This regulator is also equipped with an ON STANDBY
5. light or concealed chimney or stove pipes except for floor heating systems Installation Procedure The installation must be carried out by an electrician and com ply with local electrical codes Turn off power to the heating system at the main electrical panel to avoid electrical shock Wire the base according to your application See typical wiring diagrams in sections 4 1 and 4 2 c Fora floor heating system installation con f Th ow nect the floor sensor between the S and R ter alr minals ei S Secure the base to the wall using the provided screws and wall anchors Configure the switches located on the control module if any Refer to the user guide PB112 024T 15S PB112 024T 15S Installation Instructions 24 V Low Voltage Power Base Install the control module onto the base Apply power to the heating system 0O00 Verify the installation by checking that the heating system can be turned on or off using the thermostat 4 1 Single SSR with Built in Transformer RT850T PB112 024T e J co c W W R R Qs Electrical Panel Blue Red L2 L1 Black Heater 4 2 Multiple SSRs with External Transformer PB112 024T Electrical CWRS OSSY ul kE i VDC External
6. nteed against workmanship defects for a one year period following the initial date of purchase During this period AUBE Technologies Inc will repair or replace at our option and without charge any defective product which has been used under normal conditions The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation This warranty cancels and replaces any other manufacturer s express or implied warranty as well as any other company commitment AUBE Technologies Inc cannot be held liable for related or random damages following the installation of this product The defective product as well as the purchase invoice must be returned to the place of purchase or mailed prepaid and insured to the following address INC ONE 1 YEAR LIMITED Aube Technologies Inc 705 Montrichard Saint Jean sur Richelieu Quebec Canada J2X 5K8 Operation The TH113 R regulator operates on perpetual 15 minute heating cycles For example if the dial is set halfway the system will heat for 50 of the cycle it will be ON for 7 5 minutes and OFF for 7 5 minutes Below is a detailed table of the cycle duration based on the dial s position Position and equivalent 0 NOTE Depending on the power base used the heating cycles can be 15 seconds or 15 minutes If you have any questions concerning the TH113 R Regulator call our technical support team at
Download Pdf Manuals
Related Search