Attwood 66511 User's Manual
Contents
1. 4 and 6 Flush Mounted Cleat 66510 66511 66512 66513 66514 66516 Installation Instructions SAVE THESE INSTRUCTIONS Form Number 69343 Rev G 04 04 APPLICATION Attwood flush pull up cleats provide easy fittings for mooring and anchoring applications NOTE It is recommended that the instal n of the Attwood Flush Cleats be done by a boat builder boat dealer or a qualified marine mechanic REQUIRED FOR INSTALLATION e Adjustable wrench e Length of 3 8 9 5mm D hose e Cordless drill and bits e Sabre saw e Screwdriver e Marine sealant WARNING To prevent personal injury always disconnect the power source when installing or servicing this product Always remove the boat from the water before using any 120V AC power tools LOCATION Select an installation location that meets the following criteria e Location on vessel must be able to withstand loads specified in application section See ABYC Reg H 40 for details and ratings e Location is large enough and wide enough to accommodate the entire cleat body e Access to the underside of the vessel is necessary for both models in order to tighten the fasteners FLUSH CLEAT TEMPLATES FLUSH CLEAT INSTALLATION INSTRUCTIONS NOTE Before you drill or cut a hole on your boat BE ABSOLUTELY CERTAIN there is room for the unit beneath the deck or gunwale where it will be installed The cleat mechanism in the down position will be re2. Products that are replaced or for which a refund is issued become the property of Attwood THIS WARRANTY IS ATTWOOD S ONLY EXPRESS WARRANTY OF THIS PRODUCT NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE 1 YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES COSTS OR EXPENSES Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state 2003 Attwood Corporation 1016 N Monroe Street Lowell MI 49331 0260 www attwoodmarine com
3. The same cut out can be used when the cleat is mounted with the receptacle 1 Place water receptacle on underside of cleat and attach per flush cleat installation instructions Figure 3 The screws used must be long enough to go through the flange of the cleat deck mounting plate and then the water receptacle 2 Connect 3 8 inner diameter hose to the fitting on the receptacle Route the hose into the bilge or to a drain fitting Figure 3 _ Tension Travel J Adjustment Set Screw Cut Out Hole Backing Plate Water Receptacle Sold Separately P Lock Washer G Nut ATTWOOD LIMITED WARRANTY ATTWOOD CORPORATION 1016 North Monroe Lowell Michigan 49331 Attwood warrants to the original consumer purchaser that Attwood brand products will be free from defects in materials and workmanship under normal use and service for one year from the date of original consumer purchases This limited warranty is not applicable if the product has been damaged by accident improper installation unreasonable or improper use lack of proper maintenance unauthorized repairs or modifications normal wear and tear or other causes not arising out of defects in materials or workmanship Attwood products are warranted for use on pleasure boats Any other use including but not limited to commercial racing or non marine use are not covered under this warranty Attwood s obligation under this warranty is limited to
4. cessed beneath the deck or gunwale 1 Use templates provided to mark opening in deck Figure 1 or 2 Cut using sabre saw and drill four 1 4 6 4mm holes where indicated thru bolt cleat only 2 Remove the supplied fasteners from the studded cleat Apply a small bead of marine sealant around the edge of the cut out and place cleat in hole cut out 3 Align backing plate with the underside of the cleat For the 4 thru bolt version use 4 10 machine screws locking washers and nuts regular washers and nylock nuts can be substituted For the 6 thru bolt version use 4 1 4 20 machine screws locking washers and nuts regular washers and nylock nuts can be substituted 4 Ensure the screw is long enough to provide for proper engagement with the nut Attach washers and nuts to the studs or screws and tighten WARNING The Flush Cleats are not to be used for towing lifting or for any other anchoring application beyond those listed above Any misuse of the intended application may result in personal injury and or damage to the boat Figure 1 4 764 12 1cm o 1 657 4 21cm o o 7 8 Radius 1 429 1 75 3 63cm 4 45cm 4 Cut Out Template Figure 2 6 475 16 45cm 9 2 220 5 64cm o o 1 650 2 4 19cm 5 08cm 6 Cut Out Template OPTIONAL WATER RECEPTACLE INSTALLATION Water receptacle sold separately If using the water receptacle on Thru Bolt Version
5. repair of the product at Attwood s plant or replacement of the products at Attwood s option without expense to the original consumer purchaser Any expenses involved in the removal reinstallation or transportation of the product are not covered by this warranty The product must be returned to Attwood s plant at the address above postage prepaid and insured with proof of original purchase including date Studded Version 1 After the cleat has been installed attach water receptacle to the backing plate using 4 8 self tapping screws Figure 4 2 Connect 3 8 inner diameter hose to the fitting on the water receptacle Route hose into bilge or to a drain fitting Figure Studded Flush Cleat Studs Cut Out Hole Marine Sealant Backing Plate B Lock Washer Ge Ni Water Receptacle Sold Separately Pa b Self Tapping Screws Hose Fitting MAINTENANCE e A silicone based lubricant maybe used on cleat shafts to increase the ease of travel If Attwood is unable to replace the product and repair is not commercially practical or cannot be timely made or if the original consumer purchaser is willing to accept a refund in lieu of repair or replacement Attwood may refund the purchase price less an amount for depreciation The acceptance by Attwood of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective or in violation of any warranty
Download Pdf Manuals
Related Search