Home

Attwood 3810 User's Manual

1. 3800 Series Stainless Steel 2 Mile Sidelights Bicolor Combination Bow Light 3810 Sidelight Pair 3820 Attwood marine hardware navigational lighting bilge pumps and other marine accessories are specified more than any other brand by America s best known boat manufacturers as original equipment Look to Attwood for quality replacement parts and marine accessories SAVE THESE INSTRUCTIONS Form Number 69360 Rev A 00 01 FEATURES The Attwood Stainless Steel sidelights provide 2 mile visibility with advanced optics for greater visibility and safety The housing is corrosion proof with an aerodynamic design for an attractive appearance on the deck of your boat The base gasket forms a seal between the lens and deck for an easy waterproof installation Side reflectors provide added protection even when the light is not on These lights exceed all requirements of ABYC A 16 97 and COLREG 72 for boats up to 20 meters 65 6 feet BiColor Bow Light 3810 and up to 50 meters 164 feet Sidelight Pair 3820 REQUIRED FOR INSTALLATION e Phillips screwdriver e Drills for wire clearance hole Pilot drill for mounting screws e Two 10 pan head stainless steel screws not included LOCATION 1 Position light s on a surface of the gunwale or deck that is horizontal within 5 degrees 2 When installing bicolor combination light place it on the centerline of the boat at the bow See Figure 1a When installing sidelight pairs pla
2. BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES COSTS OR EXPENSES Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state 2000 Attwood Subsidiary Steelcase Inc 1016 N Monroe Street Lowell MI 49331 0260
3. ce lights with the red lens on the port left and green lens on the starboard right as you stand onboard facing bow of the boat Lights must be parallel to centerline of the boat See Figure 1b Figure 1a Figure 1b Green Starboard Red Port Green Starboard Red Port 3 Make sure there are no obstructions at the front or side such as rail stanchions chocks anchors cleats etc within the light s arc of visibility 112 5 degrees each side 4 Measure and mark location of wire clearance hole If installing a bicolor light location must be on the boat centerline If installing a sidelight pair both must be the same distance from the bow At the marked location s make a mark for a hole This hole is necessary for wire passage and lamp ventilation See Figure 2 Figure 2 Cover Screw e Lens Cover 10 Stainless Steel Mounting Screws Butt Joint Connectors 3 4 Hole Aligned with Boat Centerline MOUNTING INSTRUCTIONS 1 Remove the cover and lens by removing the Phillips head screw in the cover and lifting off See Figure 2 2 Align hole beneath light base with the position you ve marked for the clearance hole Set lens toward the bow and align arrow on base with the boat centerline Use the light base as a template to mark locations for the mounting screw pilot holes use at least 2 10 stainless steel screws CAUTION Positio
4. lens grooves and base screw mount lines up with the lens screw hole Be sure the gasket is outside the lens at the back Figure 4 Detail 6 Place stainless steel cover over lens Be sure gasket is inside the stainless steel cover at the back Reinstall screw into cover See Figure 5 Figure 5 Lens Cover MAINTENANCE To replace lamp Remove the cover screw cover and lens You may need to pry the lens from the gasket with a small flat screwdriver starting in the front of the light Remove old lamp by rotating 1 8 turn counterclockwise and pulling forward Replace lamp with the proper bayonet bulb Attwood Part Number 912717 Check position of O ring on the base screw mount Carefully replace lens and cover on gasket to maintain the waterproof seal Reinstall cover screw ATTWOOD LIMITED WARRANTY ATTWOOD CORPORATION 1016 North Monroe Lowell Michigan 49331 Attwood warrants to the original consumer purchaser that Attwood brand products will be free from defects in materials and workmanship under normal use and service for one year from the date of original consumer purchases This limited warranty is not applicable if the product has been damaged by accident improper installation unreasonable or improper use lack of proper maintenance unauthorized repairs or modifications normal wear and tear or other causes not arising out of defects in materials or workmanship Attwood products are warranted for u
5. n holes carefully on aluminum boats so that wires do not contact the hull 3 Drill clearance hole and pilot holes for the mounting screws WIRING INSTRUCTIONS The power supply must be 12 volt DC ONLY Use crimp type marine grade connectors with suitable insulation Protect all connections with suitable materials NOTE Failure to make proper connections and fuse the light properly see back page will void the product warranty 1 Connect one lead to the negative post of the 12 volt supply Connect the other lead to a fused and switched positive 12 volt supply Sidelights require 1 amp fusing per lamp a 1 amp fuse for the Bicolor Combination light a 2 amp fuse for the Sidelight Pair Note that navigation rules require sidelights to be operated separately from anchor lights Use either two switches or a single switch with three positions for off anchor running See Figure 3 Figure 3 2 Amp Fuse 2 Check gasket to be sure the hole lip is down Feed wires and connectors down through the gasket See Figure 4 3 Be sure base is seated into the gasket ring all the way around See Figure 4 Detail 4 Align base so the hole lip fits down into the wire clearance hole Insert two 10 stainless steel mounting screws and fasten them to the deck Note Do not fasten screws so tightly that the gasket is deformed 5 To replace lens Be sure O ring is seated on the base screw mount Seat lens so the base tabs fit in the
6. se on pleasure boats Any other use including but not limited to commercial racing or non marine use are not covered under this warranty Attwood s obligation under this warranty is limited to repair of the product at Attwood s plant or replacement of the products at Attwood s option without expense to the original consumer purchaser Any expenses involved in the removal reinstallation or transportation of the product are not covered by this warranty The product must be returned to Attwood s plant at the address above postage pre paid and insured with proof of original purchase including date If Attwood is unable to replace the product and repair is not commercially practical or cannot be timely made or if the original consumer purchaser is willing to accept a refund in lieu of repair or replacement Attwood may refund the purchase price less an amount for depreciation The acceptance by Attwood of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective or in violation of any warranty Products that are replaced or for which a refund is issued become the property of Attwood THIS WARRANTY IS ATTWOOD S ONLY EXPRESSED WARRANTY OF THESE PRODUCTS NO IMPLIED WARRANTY INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE EXTENDED BEYOND THE WARRANTY PERIOD STATED ABOVE FOR EACH PRODUCT ATTWOOD SHALL NOT

Attwood 3810 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents