ATEN Technology ATEN VS-291 User's Manual
Contents
1. Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that which the receiver is connected Consult the dealer or an experienced radio television technician for help This product is ROHS compliant re ce 2 OVERVIEW The VS 291 VS 491 Video Switches are control units that allow you to conveniently display the video output of two VS 291 or four VS 491 separate computer systems on a single monitor thereby eliminating the unnecessary expense of purchasing a separate monitor for each computer The units use electronic switching technology rather than mechanical switching for greater reliability and durability The VS 291 VS 491 also saves on the space that additional monitors take up as well as the extra power costs and eliminates the inconvenience and wasted effort involved in constantly moving around from one computer to another FEATURES Electronic Switching For Greater Reliability and Durability Display the Output of Two VS 291 or four VS 491 Computers on a Single Monitor High Resolution Video Up To 1920 x 1440 DDC2B Supports VGA SVGA XGA and Multisync Monitors Easy Installation No Software Required No Configuration Necessary Computer Selection via Pushbutton Switch HARDWARE REQUIREMENTS One VGA SVGA XGA or Multisync compatible analog monitor2. a PORT SWITOH USER MANUAL VS 291 VS 491 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and or any devices that connect to them This package contains w 1 Video Switch VS 291 or VS 491 w 1 DC 9V Power Adapter w 1 User Manual If anything is damaged or missing contact your dealer Copyright 2002 2006 ATEN International Co Ltd Manual Part No PAPE 1181 100 Printing Date 03 2006 ATEN and the ATEN logo are trademarks of ATEN International Co Ltd All rights reserved All other trademarks are the property of their respective owners Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures
3. with a standard PC high density cable having a 15 pin D type male connector One VGA SVGA XGA or Multisync analog video card having a standard PC 15 pin D type female connector per computer One video cable having a 15 pin D type male connector at one end and a 15 pin D type female connector at the other per computer Note 1 Cables require a separate purchase UL 2919 rated cable is recommended for the best video quality 2 This product is not suitable for CGA EGA or Monochrome type monitors using a digital video signal VS 491 FRONT VIEW No Description Function 1 Port Selection Press this button to cycle the video focus among the Switch computers 2 Selected Port The numbers correspond to the video ports on the LEDs back panel A LED lights to indicate that its corresponding port is the one that has the video focus Note The VS 291 Front View is similar to the VS 491 except it only has two Selected Port LEDs VS 491 REAR VIEW uF AL uF CPU 3 No Description Function 1 Monitor Port The monitor cable plugs in here 2 Video Ports The video cables that connect to the computer video ports plug in here 3 Power Jack The Power Adapter cable plugs in here Note The VS 291 Rear View is similar to the VS
4. 491 except it only has two Video Ports INSTALLATION Installation is simply a matter of plugging in cables Refer to the diagrams above as you follow the step by step directions below 1 Plug the monitor cable into the unit s Monitor port 2 Plug the female end of a male to female video extender cable into any available video port on the unit s rear panel plug the male end of the cable into the computer s video output port Note The video extender cable does not come with the package and must be purchased separately part no 2L 2401 Plug the power adapter supplied with this package into an AC source plug the adapter s power cable into the unit s Power Jack Power On all equipment If al EA LS b gt Lp LH l o bal IP gt SPECIFICATIONS Function VS 291 VS 491 Connectors Output 1 x HDB 15 Female Input 2 x HDB 15 Male 4 x HDB 15 Male Power 1 x Power Jack LEDs Selected Ports 2 4 Port Selection 1 x Push Button Switch Video Resolution 1920 x 1440 60Hz DDC DDC2 DDC2B Cable Distance 10m 30 Signal Type VGA SVGA XGA Multisynce Power Consumption DC 9V 0 9W max DC 9V 1 35W max Environment Operating Temp 0 50 C Storage Temp 20 60 C Humidity 0 80 RH Non condensing Physical Housing Plastic Met
5. al Properties Weight 0 22 kg LxWxH 12 x 6 5 x 4 4 cm LIMITED WARRANTY IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and specially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquires please contact your direct vendor
Download Pdf Manuals
Related Search