ATD Tools Range ATD-5203 User's Manual
Contents
1. ATD 5203 30 GALLON PRESSURIZED OIL DRAIN TANK ASSEMBLY 8 OPERATING INSTRUCTIONS TECHNICAL SPECIFICATIONS Model ATD 5203 Capacity 30 Gallon Drain Funnel Adjusts from 47 25 to 70 5 Drain Funnel Diameter 15 75 Plastic Tray 11 8 x 11 8 x 2 2 Swivel Castors 2pc 4 X 1 2 Wheels 2pc 7 X 1 5 Working Pressure lt 7 psi 0 5bar IMPORTANT READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT READ AND UNDERSTAND ALL SAFETY WARNINGS AND PRECAUTIONS CONTAINED IN THIS MANUAL KEEP THIS INSTRUCTION FOR FUTURE REFERENCE Warning When using product basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur lt must be understood by the operator that common sense and caution are factor which cannot be built into this product but must be supplied by the operator INSPECTION Check for worn parts air leaks and damaged loose or missing parts before operating Check tank operation by connecting air to air nipple and closing ball valve Verify that there is sufficient air flow coming from nozzle hose assembly An annual tank component inspection is recommended READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT Keep Work area clean Cluttered areas invite injuries 2 Observe work area conditions Ke2. BEFORE you assemble and use the product Before operating the tool be sure that you have all parts described in parts list in and assembly diagram located on the last pages of this manual E Slide two wheels 19 onto each end of the axle located at the base of the Tank 40 secure with washer and circlip 417 amp 18 Insert the bolts on top of the casters 22 into the flange plates Slide flat washer 21 and thread nut 20 onto bolt Tighten securely Insert handle 31 into the two slots on the side of the oil tank 40 Tighten down handle screws Attach the valve assembly 6 7 amp 8 to the oil pipe 10 Attach the funnel assembly 1 2 3 4 8 5 to valve assembly Slide drain tube 10 up through the tube holder slide the tension collar 13 onto the tube and seat it down inside of the tube holder Slide the tension nut 14 over the tube and thread it onto the tube holder Tightening this nut should increase tension on the tube holding it in place Slide the second tension collar and nut 11 8 412 onto the tube over the first tension nut assembly When tightened this will provide a stop in case the oil pan should slide downwards Tighten snugly but do not over tighten as these tension collars are both used for adjusting the height of the oil drain pan Now attach the funnel and valve assembly 1 2 3 4 8 5 to the top of the drain tube Snap plastic tray 39 onto the tabs provided on top o
3. HERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO ATD 5203 ATD 5203 _ITEM ORDERING PART PARTDESCRIPTION 4 PRT5203 04 CONNECTOR___________ 6 PRT5203 06 BOLT 8 PRT5203 08 1 BALLVALVE__________ 9 PRT5203 09 CONDUIT CONNECTOR 40 PRT5203 40 TANKASSEMBLY __________
4. e Check for loose screws misalignment binding of moving parts improper mounting broken parts and any other condition that may affect its safe operation lf abnormal noise or vibration occurs turn off the air compressor immediately and have the problem corrected before further use Refer to Warnings and precautions sections DO NOT use a damaged product 2 CAUTION Always disconnect this product from its air supply and release all compressed air from the system before performing any cleaning servicing maintenance 3 Keep the outside of the equipment free of oil grease Use only a mild soap and damp cloth when cleaning DO NOT use a flammable or combustible solvent 4 Before and during each use inspect the oil indicator level DO NOT fill tank above maximum oil level PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY A CERTIFIED AND LICENSED TECHNICIAN AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS T
5. ep area well lighted 3 Store idle equipment When not in use the product must be stored in a safe and clean location Always lock up products and keep out of reach of children 4 Use the right product for the job There are certain applications for which the product was designed DO NOT modify the product and DO NOT use the product for a purpose for which it was not intended 5 Check for damaged parts Before using any product any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for any broken or damaged parts and any other conditions that may affect its operation Replace or repair damaged or worn parts immediately 6 Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty 7 DO NOT operate product if under the influence of alcohol or drugs 8 DO NOT exceed the product s working pressure of 7 psi 0 5bar 9 Only use on a flat surface capable of supporting the product and its maximum load 10 Dress safely Non skid footwear or safety boots should be used when working with the product DO NOT wear loose clothing or jewelry as they can become caught in moving parts Wear a protective hair covering to prevent long hair from becoming caught in moving parts 11 DO NOT allow children in the work area 12 Always check hardware and assembled parts after assembling All connectio
6. f the oil tank Check all connections to hoses and valves to ensure that there will be no leaks Check to make sure all hardware is secured tightly Also check to make sure the wheels rolls properly before using your oil drain tank TO DRAIN OIL Raise drain bowl to desired height and lock in place with tension adjusting knob 12 With valve 8 fully open Valve handle in vertical position drain oil into bowl tank assembly DO NOT fill the reservoir above the maximum oil level as shown TO EVACUATE OIL Evacuate used oil from tank when maximum oil level is obtained Raise drain bowl and lock in place Close the ball valve 8 fully by turning it to horizontal position Place hose and nozzle 27 SECURELY into your used oil collection reservoir and open the ball valve 26 by turning it to vertical position Connect air supply to air inlet connector 33 and discharge oil Never leave unit unattended when evacuating oil Immediately disconnect air supply when oil is no longer discharging into reservoir TO TRANSPORT TANK With ball valve 8 fully open valve handle in vertical position lower drain bowl to desired height Always use the tank handle to transport the tank assembly Always grasp the handle with two hands while moving the load Do not pull unit by the funnel tube or hoses CLEANING AND MAINTENANCE 1 Before each use examine the general condition of the entire oil drain system Inspect air hoses for damag
7. ns should be checked and hardware tightened 13 DO NOT overreach Keep proper footing and balance at all times to prevent tripping falling and injury 14 Always secure the wheels and casters in place while operating the product 15 Know and obey city and state laws for proper disposal of oil Dispose of oil properly in accordance with all local laws and regulations SPECIFIC PRODUCT WARNING AND PRECAUTIONS Note This Product is to be used only for transporting oil DO NOT use to transport any other liquid 1 Always disconnect equipment from its air supply source and release all compressed air from the system before performing any service or maintenance Never leave this product unattended while operating or evacuating oil Never use this equipment near open flame or heat sources Always raise Drain Bowl and close ball valve 8 before evacuating oil Never attempt to pressurize the tank with the ball valve open If the bleeder valve ever relieves any air pressure from the tank remove the unit from service immediately and contact a qualified service technician If used oil does not evacuate from tank upon pressurization check that ball valves are fully in the correct positions If this does not correct the problem removed the unit from service and contact a qualified service technician ASSEMBLY This unit requires some assembly before use lt is important that you read the entire manual to become familiar with the product
Download Pdf Manuals
Related Search