ATD Tools ATD-6903 User's Manual
Contents
1. ATD 6903 1 0MM TOUCH UP GUN W CUP INSTRUCTION MANUAL Read this manual carefully and understand it completely Retain Manual for future use Always follow safety precautions to prevent personal injury and or damage to the equipment Illustrations and photos are intended for reference only Actual product may vary Specifications are subject to change without notice Important Safety Instructions 1 Always wear eye protection gloves and respirator to prevent against harmful vapors while spraying 2 Never use oxygen or any other combustible or bottle gas as a propellant Explosion and serious injury or death may result 3 Many paints and solvents can be highly flammable Please use the spray gun only in well ventilated areas do not smoke or use near open flame 4 Always disconnect the paint gun from air supply when not in use and during maintenance For emergency stopping and to prevent unintended operation a valve near the gun is recommended 5 Inspect the tool before each use to ensure there is no leakage or misaligned parts Be sure the trigger moves freely 6 Never use halogenated hydrocarbon solvent as it can chemically react with aluminum and zinc parts of this tool 7 Do not make any modifications to this tool Figure 1 Operating Instructions POWER SOURCE This tool operates best on a clean dry supply of compressed air delivered at 29 to 90 psi Use of a moisture trapping air filter is highly recommended as2. moisture or foreign matter can damage the internal parts of this tool CAUTION All air pressure in the system should be rated at 29 to 50 psi Higher or lower pressure can adversely influence the operation or cause damage to this tool NOTE o maintain a maximum 10 PSI at the nozzle use a maximum of 29 psi at the inlet TOOL PREPERATION 1 Check tool for worn or damaged parts Repair or replace as necessary 2 Check trigger to ensure that it moves freely 3 Connect tool to air supply 4 Adjust air pressure based on paint viscosity and paint manufacturer s recommendation fig 2 5 Clean paint guns before use to ensure any factory oils or pigments are not present Do not use halogen hydrocarbon or acidic solvents to clean paint guns 6 Pour paint into cup Figure 2 Lock Knob Pull to unlock Turn to set desired pressure Push to lock GUN HANDLING For best results please follow these basic guidelines 1 Keep the spray gun perpendicular to the surface Spraying in an arc will not give good results Fig 3 2 Keep gun moving from one side to the other while spraying If you stop moving the gun while you are spraying too much paint will build up and begin to run Begin the horizontal movement of the gun before you begin spraying Also keep the gun at a constant distance 6 12 inches from the surface Fig 4 Figure 3 INCORRECT Light Heavy Light Coating Coating Coating Figure 4 CORRECT Pai
3. nt surface 6 to 12 Inches b Start Pull se Release End stroke Trigger A Trigger Stroke Direction of stroke ADJUSTMENT 1 Fine tune the gun to your desired working settings of spray patters fluid output and degree of paint atomization using the three controls illustrated in Figure 5 Figure 5 Fluid paint Adjustment Knob Spray pattern Adjustment Knob Air Adjustment Knob Maintenance To clean the gun pour any leftover paint back into its container Using thinner clean out the paint cup and cap Spray some thinner through the gun to clean the spray head needle and nozzle Spray until thinner comes out clean Clean all paint passages as any paint left in the gun and allowed to dry can clog the spray head Wipe the exterior of the gun with the cleaning brush included and a soft cloth moistened with thinner If you remove the needle remove the nozzle as well to protect the seat NEVER DIG WITH A WIRE OR HARD OBJECT AS THIS CAN DAMAGE THE NEEDLE SEAT Remove all such paint before it has a chance to dry ATD 6903 oo 1 0mm Gun ey 3 r EI ITEM ITEM ORDERING PARTY PART DESCRIPTION 9 PRTe900 22 FLUID INLET JOINT FLUID ADJUST ASSY 1 0mm TIP KIT NEEDLE FLUID NOZZLE AIR CAP PATTERN ADJUST ASSY RT6900 18 NEEDLE PACKING ASSEMBLY GUN BODY 13 PRT6900 26 PRT6900 20 LID FOR CUP ATD6926 8 PRT6900 10 FILTER PACK OF 10 ET ooo go o o o o o o soo
Download Pdf Manuals
Related Search