AT&T TRIMLINE MODELS User's Manual
Contents
1. AT amp T qi SINGLE LINE BUSINESS TELEPHONES DESK WALL AND TRIMLINE MODELS kel n APRIL 1986 403683022 999 500 270 IS 950 270 IS INTRODUCTION This booklet contains installation and removal instructions for standard modular desk or wall telephones Installation of the following options requires a professional installer e Adjunct Dialer e SPOKESMAN Loudspeaker e External Speakerphone e Headset Adapter Contact your place of purchase for details Package Content Make sure your package contains the following items Telephone e Handset e Handset cord e Line cord e Number card Modular Outlet Requirement You must have a standard modular telephone jack such as one of those shown below to install your phone If you have one of these jacks already mounted no tools are needed JACK OPENING Jacks for Desk or Trimline Telephones eo Le i JACK a OPENING Uren Le te esas Jack For Wall Telephone Figure 1 Standard Modular Telephone Jacks If you do not have a standard modular telephone jack contact your local telephone company or AT amp T Information Systems for details on converting your present outlet to a modular jack INSTALLATION Your telephone is fully assembled except for the coiled handset cord and clear line cord To Install Your Desk Or Trimline Telephone 1 Plug one end of the coiled handset cord into the atte in the handset Push the plug in until2. RJ14C RJ36X 2503CM RJ11C RJ14C RJ36X 2504BM RJ11C RJ14C RJ36X 2504CM RJ11C RJ14C RJ36X 2514BM RJ11C RJ14C RJ36X 2514CM RJ11C RJ14C RJ36X 2554BMPA RJ11C RJ14W 2554BMPB RJ11W RJ14W The apparatus code is stamped on the bottom of the set In compliance with the rules you should be aware of the following 1 Connection of this equipment to the telephone network must be through one of the standard network interface jacks listed above These may be ordered from the local telephone company or through AT amp T Information Systems as your authorized agent 2 Customers connecting equipment to the telephone network shall upon request of the local telephone company provide the following information e The telephone number assigned to the line used with this telephone e The Registration Number and the Ringer Equivalence Number REN from the Registration label on the bottom of the telephone Note This equipment is registered to be used on telephone lines with A type ringing frequencies However some telephone companies use a variety of other ringing frequencies e g B C Asa result this telephone may or may not ring properly when connected to a telephone line that provides other than A type ringing Consult your AT amp T Information Systems representative for advice 3 Notify the local telephone company when this equipment is permanently disconnected from the line 4 If tr
3. er card on your telephone following the instructions on the back of the number card label RINGER VOLUME CONTROL RIVETS JACK wx COILED HANDSET WALL corp JACK PHONE PLUG COILED HANDSET CORD Sa Figure 4 Wall Telephone Installation To Remove Your Telephone 1 To disconnect or remove your telephone reverse the installation procedures To remove any modular plug squeeze the clip of the plug and pull it out of the jack To disconnect a wall set slide the set up to lift it off the rivets and pull it away from the wall Warranty All terms and conditions specified in your agreement with AT amp T apply Federal Communications Commission Registration Information Statement Part 68 The following information is applicable only to equipment connected directly to the telephone network and not to connection of stations behind terminal systems The following equipment is registered with the Federal Communications Commission FCC in accordance with Part 68 of its ules Apparatus Standard Network Code Interface Jack s 500ADM RJ11C RU14C RJ36X 500BDM RJ11C RJ14C RJ36X 500MM RJ11C RJ14C RJ36X 500SM RJ11C RJ14C RJ36X 503CM RJ11C RU14C RJ36X 514BMW RJ11C RU14C RJ36X 514CM RJ11C RU14C RJ36X 554BMPA RJ11W RJ14W 2223C RJ11C RJ17C 2224C RJ11W RJ17C 2500MM RJ11C RU14C RJ36X 2500MMG RJ11C RU14C RJ36X 2500MMGB RJ11C RJ14C RJ36X 2500MMGF RJ11C RJ14C RJ36X 2500SM RJ11C
4. it clicks Figure 2 2 Plug the other end of the cord into the side opening in the base Push the plug in until it clicks 3 Plug one end of the clear line cord into the jack in the base of the telephone Push the plug in until it clicks N yack JACK JACK fo HANDSET CLEAR COILED LINE HANDSET CORD CORD Figure 2 Desk Telephone Installation RINGER VOLUME CONTROL HANDSET RINGER VOLUME CONTROL q q TAT A CCRC COILED HANDSET CORD Figure 3 Setting the Ringer Volume Control Desk and Trimline Telephones 4 Plug the other end of the cord into the telephone jack in your office Push the plug in until it clicks 5 Turn your telephone over or for Trimline telephones lift the handset Figure 3 6 Set the ringer volume switch or thumbwheel to the setting you want To Install Your Wall Telephone 1 Align the wall phone plug with the jack then line up the hole in the back of the telephone set with the rivets on the wall outlet plate Push in and slide the telephone down into place Figure 4 lu Plug one end of the coiled handset cord into the jack in the handset Push the plug in until it clicks Plug the other end of the cord into the jack in the bottom of the wall base Push the plug in until it clicks Adjust the ringer volume switch on the upper right side of the telephone to the desired setting For All Telephones Place the numb
5. old for BUSINESS SYSTEMS APPLICATIONS ONLY Use in a residential environment could result in an electrical short circuit when the telephone wiring is set up to provide other applications e g appliance control power transformers lighting telephones etc The AC power used in these applications may create a safety hazard since lifting the handset from the telephone base places a direct short circuit across the telephone wiring
6. ouble is experienced the telephone set should be unplugged from the network interface to determine if the telephone set or the telephone line is the trouble source If your telephone set is determined to be malfunctioning it should not be reconnected until repairs are made O Repairs to this equipment other than routine repairs can be made only by AT amp T Technologies or its authorized agents If a telephone set causes harm to the telephone network the local telephone 9 gt company may temporarily discontinue your service and if possible notify you in advance If advance notice is not practical you will be notified as soon as possible You will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC The local telephone company may make changes in its facilities equipment operation or procedures that could affect the proper functioning of your equipment If they do you will be given adequate notice in writing to allow you an opportunity to maintain uninterrupted telephone service Hearing Aid Compatibility These telephones are compatible with inductively coupled hearing aids as prescribed by the Federal Communica tions Commission FCC except for Models 223C and 224C CAUTION The following safety information is important to you All of the telephones listed with the exception of message waiting models are NOT FOR RESIDENTIAL USE They are s
Download Pdf Manuals
Related Search