Home

AT&T Door Phone Controller User's Manual

Contents

1. TELEPHONE OR TELEPHONE SYSTEM TRUNK Figure D 1 Installation Method Used For Answering Only Telephone Calls TYPICAL ANSWERING MACHINE TO TEL TO TEL LINE JACK SET JACK CAUTION SET ANSWERING MACHINE FOR A LIMITED LENGTH INCOMMING MESSAGE ONLY TELEPHONE OR TELEPHONE SYSTEM TRUNK Figure D 2 Installation Method Used For Answering Both Door and Telephone Calls D 2 Using With an Answering Machine Appendix E Auxiliary Alert Option Installation Instructions The following instructions utilize the WP91683 L1 Power Supply for the AT amp T Door Phone Controller external alert feature APPLICATION The WP91683 L1 Power Supply is the interface for providing INFORMATION 48VDC to operate external alert features for the AT amp T Door Phone Controller such as bells horns lamps strobes and chimes The WP91683 L1 Power Supply is a plug in power supply capable of providing 48VDC at up to 200 milliamps The power supply operates from a 115 120 volt AC standard single or duplex receptacle HOW IT WORKS The AT amp T Door Phone in conjunction with a telephone system provides a means to alert a customer that a doorbell button has been pressed In response the customer can answer and talk to the door from a telephone within the customers premises The alerting device function can be provided by an external alert device powered by the WP91683 L1 Power Supply The AT amp T Door Phone s AUX ALERT contact closu
2. 3 6 Installation Home Residential The Forced Disconnect Time out option does not apply when setting options unless 2 minutes elapse without a Touch Tone selection 4 To exit option selection mode press 3 on the telephone keypad you will hear 2 beeps Hang up the phone 5 Set position 8 of the AT amp T Door Phone Controller DIP switch back to the OFF position Operation Basic Door Answer Function Visitor Presses Door Speaker Button When a visitor presses the door speaker push button the AT amp T Door Phone Controller will signal the telephone equipment inside your home or building to ring and activate a door bell chime device optional Any additional presses on the door speaker push button will be ignored until the option selected ring chime duration has expired with the exception that a confirmation tone will still be sent to the speaker when the door button is pressed Answering a Call from the Door Speaker The person inside the building can simply answer the ringing phone and establish two way communications with the door speaker To open the door the person inside the building either enters the Door Code on the telephone s keypad or presses the customer provided door unlock push button Either of these actions will activate the customer provided electric door strike plate device Installation Home Residential 3 7 As an alternative response when the telephone or door bell chime
3. Figure 2 6 Connections for Electric Door Strike Plate optional 2 16 Installation Procedures 3 Verify all connections when connecting the door strike contacts on the AT amp T Door Phone Controller to existing door open buttons Make sure of the following NOTE One or the other will m The NO and C contacts are connected in parallel to a apply not both normally open button M The NC and C contacts are connected in series to a normally closed button Auxiliary Alert Device optional In most configurations the Door Phone Controller will cause a telephone to ring when the doorbell button is pushed An aux iliary alert device chime bell horn tone generator etc can also be used as an alert to notify the person inside the building that the doorbell button has been pushed Auxiliary Alert If the Auxiliary Alert Device has Mode A low voltage device 24V or less is recommended more T Amp draw men Follow the steps below refer to for wiring auxiliary an external relay arrangement will be required alert device door bell chime to the Door Phone Controller 1 Install the auxiliary alert device door bell chime as in structed by the manufacturer s installation manual See Appendix E for specific 2 The Normally Open N O and Common C relay con auxiliary alert device installation tact located on the Door Phone Controller back panel are accessible at the Door Phone Con troller
4. OFF Dedicated Trunk ON Selects between Trunk Savor or Port Saver This switch only has meaning when Trunk Access is selected with Switch 1 and Shared Trunk is selected with Switch 2 Trunk Saver OFF Port Saver ON Selects between Loop Start and Ground Start This switch only has meaning when Trunk Access is selected with Switch 1 Loop Start OFF Ground Start ON Selects between Auxiliary Alert or Ringdown This switch only has meaning when Station Access is selected with Switch 1 Auxiliary Alert OFF Ringdown ON Not used Not used Selects between Option Selection Mode and Normal Operation This switch acts as a Option Selection security switch If this switch is ON any user can activate Option Selection Mode by keying in 3 on a touch tone telephone set which connects directly to the Door Phone Controller When this switch is OFF Option Selection Mode cannot be activated Normal Mode OFF Option Selection Mode ON See other side for DTMF Option Selection 1992 AT amp T CIC 999 500 315 All rights reserved Printed in U S A 011722050 055 Issue 3 November 1992 Graphics AT amp T 1988
5. To connect wires for a remote door open switch use the diagram in and follow the steps below 1 Install the remote door open button in desired location using manufacturer s installation instructions Run 2 wires 22 24AWG from the installed normally open contact remote door open switch to the Remote Door Open terminals 6 amp 7 on the AT amp T Door Phone Controller back panel polarity of wires is not important Installation Procedures 2 13 AT amp T DOOR PHONE CONTROLLER BACK PANEL AT amp T DOOR SPEAKER AND DOOR BELL BUTTON SHIELDED TWISTED PAIR 24 AWG TEA Le 1 MODEL NO 2 5 Kt APPROX 1500 FT MAXIMUM LENGTH 0000000 60 D Q eo e Y JUMPER THE TWO DOOR AJAR SWITCH TERMINALS IF DOOR AJAR DEVICE IS NOT USED DOOR AJAR SWITCH NOTE MAGNETIC SWITCH IS CLOSED WHEN DOOR IS CLOSED Figure 2 4 Connections for AT amp T Door Phone Speaker Door Button and Door Ajar Devices 2 14 Installation Procedures AT amp T DOOR PHONE CONTROLLER BACK PANEL 7 MODEL NQ 22050 055 MOMENTARY PUSH BUTTON NORMALLY OPEN Figure 2 5 Connections for Remote Door Open Switch optional Electric Door Strike Plate Device optional An electric door strike plate is used to automatically open a closed or locked door A low voltage device 24V or less is If your Electric Door Strike Plate recommended The AT
6. terminates entry 0 to 20 numerical digits and N N UN UN 2 second pause terminates entry 000 to 255 for 0 to 255 Listen For Double Beep Double Beep Double Beep Double Beep Default 30 sec 2 sec 4 sec I Enabled 120 sec After Selecting Options 1 Press 3 2 Hang up after hearing a double beep confirmation 3 Set DIP Wiocation 8 back to the OFF position to prevent unauthorized re programming See other side for DIP Switch Settings AT amp T NOTE All switches are OFF when shipped from the factory Door Phone Controller DIP Switch Settings The Door Phone Controllers operating modes are selected on the 8 position DIP switch at the front of the unit Positions 1 through 5 are used to set up the way the Door Phone Controller will interface with your telephone equipment Position 8 is used to access Option Selec tion Mode Positions 6 amp 7 are not used Definition are given below Switch 1 Selects between Trunk Access and Station Access Trunk Access OFF Station Access ON Z CAUTION Damage to the PBX Station Card may result if switch position 1 is incorrectly set Double check that switch position 1 is set to ON for Station Port Access Switch 2 Switch 3 Switch 4 Switch 5 Switch 6 Switch 7 Switch 8 Selects between Dedicated Trunk or Shared Trunk This switch only has meaning when Trunk Access is selected with Switch 1 Shared Trunk
7. 6 2 Connecting The AT amp T Door Phone Controller to 6 4 a Telephone System With Shared Trunk Port Appendix Auxiliary Alert Device Connections E 1 E 1 Connections For Auxiliary Alert Device E 3 xi Tables Installation Home Residential 3 1 3 1 AT amp T Door Phone Controller Option Selection Information 3 6 Installation Dedicated Trunk Port ion Dedi 4 1 4 1 AT amp T Door Phone Controller Option Selection Information 4 8 Installation Dedicated Station Port 5 1 AT amp T Door Phone Controller Option Selection i 5 1 Information 5 7 Installation No Dedicated Trunk Station Port ws i 6 1 6 1 AT amp T Door Phone Controller Option Selection Information 6 8 Troubleshooting and Maintenance 7 1 7 1 Troubleshooting Procedures 7 2 xii Introduction Introduction 1 1 Using This Manual 1 2 Introduction This manual will help you install program and operate the AT amp T Door Phone Controller It contains important information on what features are available and how to use them We urge you to read this manual prior to installing the AT amp T Door Phone Controller this will ensure that you are using the product to its fullest capability this section provides basic information on what the AT amp T Door Phone Controller is and what are its features Also included is a Glossary of Terms a necessity for persons not familiar with telephone equipment operation a
8. Small business telephone communications system Ground Start One method by which a business telephone system PBX signals the telephone company that you have gone off hook Used in most business applications contact your telephone company to determine if you have Ground or Loop Start Loop Start One method of signaling the telephone company that your telephone has gone off hook used for most residential and communication system applications Contact your telephone company to determine if you have Ground or Loop Start PBX Private Branch Exchange Business telephone system Ringdown In Station mode the activation of the door speaker s push button will cause the AT amp T Door Phone Controller to dial the number of a predetermined telephone station number PBX or EKTS must be installed When the telephone is answered there is direct two way communication with the door speaker Trunk Port PBX connection for Central Office or trunk lines Station Port PBX connection for station sets Hook Flash This causes telephone equipment to go on hook for a duration usually less than a second not long enough to be considered as calling for the circuit to be released Introduction 1 5 Installation Procedures Installation Procedures 2 1 2 2 Installation Procedures Important Safety Instructions When using your telephone equipment basic safety precautions should always be followed to reduce th
9. TO DOOR SPEAKER TO DOOR BELL BUTTON TO DOOR AJAR SWITCH TO REMOTE DOOR OPEN SWITCH OPTIONAL TO DOOR STRIKE PLATE DEVICE TO AUXILIARY ALERT DEVICE DOOR BELL CHIME TELEPHONE SYSTEM mo 2d ANALOG STATION PORT TO C O TRUNK PORT STATION n rv Figure 5 2 Connecting the AT amp T Door Phone Controller to a Telephone System with Dedicated Analog Station Port 5 4 Installation Dedicated Station Port Option Selection The final step of the installation procedure is selecting options for your AT amp T Door Phone Controller The selection of these Refer to Appendix B for a options must be done while in the Option Selection Mode This detailed explanation of each of these options mode lets you control such things as Delay before Door Ajar Call Back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults Phone Number Storage Memory 1 Phone Number Storage Memory 2 Installation Dedicated Station Port 5 5 Follow the steps below to select options for the AT amp T Door Phone Controller A CAUTION Never connect an AT amp T DOOR PHONE CONTROLLER with the DIP Switches optioned for TRUNK access to a STATION LINE Doing so may cause damage to the STATION LINE and or the AT amp T DOOR PHONE CONTROLLER 1 Select Option Selection Mode by setting position 8 of the A
10. FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation The AT amp T Door Phone Controller generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the AT amp T Door Phone Controller does cause interference to radio or television reception which can be determined by turning the AT amp T Door Phone Controller unit off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the radio or TV receiving antenna Relocate the unit to increase the separation with respect to the radio or TV receiver or vice versa Plug the unit into a different outlet so that it and the radio or TV receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet How To Identify and Resolve Radio TV Interference Problems helpful This booklet was prepared by the Federal Government Printing Office Washington DC 20402 Stock order No 004 000 00345 4 This equipment is registered with the Federal Communications Commission FCC in accordance with Part 6
11. Front View of the AT amp T Door Phone Controller 1 4 and Control Panel Installation Procedures 2 1 2 Door Phone Controller Back Panel Connections 2 8 2 1 2 Typical AT amp T Door Phone Controller Installation 2 10 2 3 Mounting AT amp T Door Phone Controller to Wall 2 12 2 4 Connections for AT amp T Door Phone Speaker 2 14 Door Button and Door Ajar Devices Connections for Remote Door Open Switch 2 15 i 2 16 2 5 2 7 Connections for Auxiliary Alert Device optional 2 18 2 8 Plug the AT amp T Door Phone Controller Power Cord 2 19 and Transformer to 120 VAC Oullet 2 9 Configuration of Telephone Equipment Flow Chart 2 22 Installation Home Residential 3 1 3 1 Home Residential DIP Switch Settings 3 3 3 3 4 2 Connecting AT amp T Door Phone Controller to Standard Telephone Equipment Installation Dedicated Trunk Port 4 1 4 1 DIP Switch Setting for PBX with Dedicated Trunk 4 3 Connecting Door Phone Controller to Standard 4 4 Telephone Equipment ifi 4 5 4 2a 4 2b Using Modified Modular Cable for Ground Start Installations Installation Dedicated Station Port 5 1 5 1 DIP Switch Configuration for Telephone System 5 3 with Dedicated Station Access Station Mode 5 2 Connecting the AT amp T Door Phone Controller to a 5 4 Telephone System with Dedicated Analog Station Installation No Dedicated Trunk Station Port 6 1 6 1 DIP Switch Setting for PBX With Shared Trunk Port 6 3
12. OPTIONAL TO DOOR STRIKE PLATE DEVICE TO C O Outside Line TO AUXILIARY ALERT DEVICE DOOR BELL CHIME TO TELEPHONES Figure 3 2 Connecting AT amp T Door Phone Controller to Standard Telephone Equipment Installation Home Residential Option Selection The final step of the installation procedure is selecting options for your AT amp T Door Phone Controller The selection of these Refer to Appendix B for options must be done while in the Option Selection Mode This detailed explanation of each of these options mode lets you control such things as Delay Before Door Ajar Call Back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults Follow the steps below to select options for the Door Phone Controller 1 Select Option Selection Mode by setting position 8 of the Door Phone Controller DIP switch to the ON position see Figure 1 1 2 Once the DIP switch has been set you must make con nection to the door speaker by hook flashing the phone within 5 seconds and entering 3 on the telephone keypad option selection mode is active as soon as you hear a distinctive dial tone Any or all options may be 3 Use Table 3 1 to make each option selection reselected in any order Installation Home Residential 3 5 Table 3 1 AT amp T Door P
13. amp T Door Phone Controller can provide has more than a 1 Amp current an open or closed contact when requested to interface to and draw then an external relay to operate your electric door strike plate device Once an arrangement is required electric door strike plate has been installed it can be controlled by the AT amp T Door Phone Controller unit either from entering the appropriate digits from a touch tone phone or from the Remote Open switch push button Follow the steps below and refer to for wiring the door strike plate device to the AT amp T Door Phone Controller Installation Procedures 2 15 1 Have the electric door strike plate device installed as in structed by the manufacturers installation manual Check electric installation codes and local ordinances for exact wiring requirements in your area 2 Normally Open N O Normally Closed N C and Common C relay contacts are accessible at the Door de Phone Controller terminal block Wire these to the door within the same cable as others i i wires connecting to the AT amp T strike plate device and its power source as instructed by Door Phone Controller your manufacturer s installation manual If no instruc tions exist wire the above relay contacts to the existing door open button see 3 below Do not include strike plate wires AT amp T DOOR PHONE CONTROLLER BACK PANEL we JH ELECTRIC DOOR STRIKE PLATE DEVICE WITH POWER SOURCE
14. factory The AT amp T Door Phone Controllers basic operating modes are selected on the 8 position DIP switch at the front of the unit see Positions 1 through 5 are used to set up the way the AT amp T Door Phone Controller will interface with your telephone equipment Position 8 is used to access Option Selection Mode Positions 6 amp 7 are not used The definition of each switch position is given below Switch 1 Selects between Trunk Access and Station Access Trunk Access OFF Station Access ON Switch 2 Selects between Dedicated Trunk or Shared Trunk This switch only has meaning when Trunk Access is selected with Switch 1 Shared Trunk OFF Dedicated Trunk ON Switch 3 Selects between Trunk Saver or Port Saver This switch only has meaning when Trunk Access is selected with Switch 1 and Shared Trunk is selected with Switch 2 Trunk Saver OFF Port Saver ON Switch 4 Selects between Loop Start and Ground Start This switch only has meaning when Trunk Access is selected with Switch 1 Loop Start OFF Ground Start ON Switch 5 Selects between Auxiliary Alert or Ringdown This switch only has meaning when Station Access is selected with Switch 1 Auxiliary Alert OFF Ringdown ON DIP Switch Settings 1 A 2 DIP Switch Settings Switch 6 Not used Switch 7 Not used Switch 8 Selects between Option Selection Mode and Normal Operation This switch acts as a Option Selection sec
15. is heard the person inside the building can press the door unlock push button which will stop the ringing and will open the door This allows the door to be unlatched without the use of a phone Calling the Door Speaker from Inside the Building To initiate a call to the door the person within the building simply takes the telephone off hook and hook flashes the telephone within the first 4 seconds At this point there will be direct two way communication from within the building to the door speaker Telephone Line In Use When Visitor Presses Door Speaker Button Once the push button is pressed you can Hook Flash to the door speaker and then back to the original call only once unless the push button is pressed again If you forget to hook flash back to the original call the AT amp T Door Phone Controller will call you back If a visitor presses the door speaker button while an existing call is already taking place on the C O line the AT amp T Door Phone Controller will generate a door alert signal to indicate a visitor needs attention at the entrance The person inside the building can hook flash the phone and be in direct two way communication to the door speaker Then normal AT amp T Door Phone Controller functions can take place When door phone functions have been completed i e door has been remotely opened hook flashing the phone again within the forced disconnect timeout or pressing 9 will return the lin
16. know if the telephone system is configured for auxiliary alert mode or ringdown mode see for explanation of ringdown and auxiliary modes 5 2 Installation Dedicated Station Port LEGEND AUX ALERT MODE configure your telephone system for Ringdown RINGDOWN MODE 2 3 s ON for Option Selection Mode Only B Y HIE 5 Figure 5 1 DIP Switch Configuration for Telephone System with Dedicated Station Access Station Mode Installation When moving the AT amp T Door To customize the AT amp T Door Phone Controller for this type of Phone Controller or adding or installation you must properly configure the 8 position DIP switch located the Door Phone Controller front panel see panel unplug transformer from 120V outlet Also unplug the Figure 1 1 Use the Flow Chart in Figure 5 1 to properly set terminal strip and modular the DIP switch phone connectors on the back panel Installation Dedicated Station Port 5 3 Install the AT amp T Door Phone Controller using the information in Section 2 Refer to Figure 5 2 AT amp T DOOR PHONE CONTROLLER BACK PANEL J1 HOST O ufo eooc onou DEE TRAL Ow ied Mil ilu NA sen t INE iE ui qu cm 12 VAC ADE Canes TERMINAL BLOCK HARD WIRE CONNECTOR NOT USED
17. products purchased or operated outside the United States You may be required to provide AT amp T with proof of purchase before AT amp T will perform any warranty repair or provide any warranty replacements EXCEPT AS SPECIFICALLY SET FORTH ABOVE ATST ITS AFFILIATES SUPPLIERS AND DEALERS MAKE NO WARRANTIES EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIM ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE EXCEPT FOR PERSONAL INJURY THE LIABILITY OF AT amp T ITS AFFILIATES SUPPLIERS AND DEALERS FOR ANY CLAIM LOSS DAMAGE OR EXPENSE FROM ANY CAUSE WHATSOEVER REGARDLESS OF THE FORM OF THE ACTION WHETHER IN CONTRACT TORT OR OTHERWISE SHALL NOT EXCEED THE LESSER OF DIRECT DAMAGES PROVEN OR THE REPAIR OR REPLACEMENT COST OF THE SYSTEM OR THE SYSTEM S PURCHASE PRICE IN NO EVENT SHALL AT amp T ITS AFFILIATES SUPPLIERS AND DEALERS BE LIABLE FOR INCIDENTAL RELIANCE CONSEQUENTIAL OR ANY OTHER INDIRECT LOSS OR DAMAGE INCLUDING LOST PROFITS OR REVENUES SUSTAINED OR INCURRED IN CONNECTION WITH THE SYSTEM THIS LIMITATION OF LIABILITY SHALL SURVIVE FAILURE OF THE EXCLUSIVE REMEDY SET FORTH IN THE LIMITED WARRANTY ABOVE FCC Regulations and Warranty THIS PAGE IS PERFORATED FOR REMOVAL Ah AT amp T Options Delay Before Door Ajar Call back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time
18. terminal block Wire these to the auxiliary alert device and it s power source as instructed by the manufacturers installation manual Connecting Power When the Door Phone Controller has been mounted to a wall or placed on a shelf and all cables and wires have been connected to the back panel plug the transformer into a 120 VAC outlet See Installation Procedures 2 17 AT amp T DOOR PHONE CONTROLLER BACK PANEL DOOR BELL CHIME AUXILIARY ALERT C DEVICE WITH POWER SOURCE Figure 2 7 Connections for Auxiliary Alert Device optional MODEL NO 22050 055 2 18 Installation Procedures Figure 2 8 Plug the AT amp T Door Phone Controller Power Cord and Transformer to 120 VAC Outlet Installation Procedures 2 19 Operation and Controls Information Door Ajar Function Default Condition After the door has been opened by the four digit code or the remote push button the Door Phone Controller will wait for the Door Ajar Call back time out to elapse At this point if the door is still open the Door Phone Controller will call back the phone chime for the duration of the ring chime duration and then repeat after the Door Ajar Call back time out has elapsed again If the phone is answered during that time a Door Ajar Tone will be heard The Door Ajar Tone will cease when any DTMF Digit is pressed or the user speaks or hangs up Alternate Condition If the d
19. 1 jack for the telephone PBX interface B one RJ11 jack for Central Office interface one connector mounted terminal strip Length 10 5 Width 9 5 Height 2 5 Weight 5 5 Lbs Appendix D Using the Door Phone Controller With An Answering Machine Installation Information When configuring the AT amp T Door Phone Controller to answer both the door and telephone calls be sure to change your outgoing message accordingly This Appendix provides two methods for configuring an answering machine to the AT amp T Door Phone Controller The first method diagrams how to connect the AT amp T Door Phone Controller with an answering machine so that only regular telephone calls are answered by the answering machine see The second method diagramed will allow the answering machine to answer both regular telephone calls and calls from the Door Speaker see A CAUTION When using your answering machine to answer both door and telephone calls make sure to set your answering machine to allow for a limited length in coming message Do not use an answering machine that cannot limit the incoming message length Using With an Answering Machine D 1 TYPICAL ANSWERING MACHINE TO TEL TO TEL LINE JACK SET JACK TO PHONE C O AT amp T DOOR PHONE CONTROLLER SHARED TRUNK MODE TO J2 TO J1 CONNECTOR CONNECTOR PHONE C O AT amp T DOOR PHONE CONTROLLER SHARED TRUNK MODE TO J2 TO J1 CONNECTOR CONNECTOR
20. 11 16 92 i ETPTHEPEHI mm rom M AT amp T Door Phone Controller Installation and Operation Manual 1992 AT amp T CIC 999 500 315 All Rights Reserved 011722050 055 Printed in U S A Issue 3 November 1992 NOTICE Every effort was made to ensure that the information in this manual was complete and accurate at the time of printing However information is subject to change COMPATIBILITY The AT amp T Door Phone Controller is recommended for use with any AT amp T business telephone system It is also intended to be used with the AT amp T Door Phone Speaker WARRANTY INFORMATION AT amp T provides a limited warranty to this product Refer to Warranty Information in Partner Spirit Merlin System Dimension Horizon Touch Tone and Comkey are registered trademarks of AT amp T VG AT amp T Door Phone Controller Compatibility Chart Dedicated Dedicated Port Trunk Station Station Mode Trunk Trunk Saver Saver Access Access Auto Loop Ground Loop Loop Aux Alert Ringdown N Start Start Start Start Analog Analog System Section Section Section Section 3 6 Section Section see see DIP Switches Home Use single line NO NO NO YES NO NO service PARTNER YES NO YES YES NO NO PARTNER YES NO YES YES YES YES PLUS s e see see Notes 11 12 see Spirit YES NO YES YES NO NO 308 616 see see see 1224 2448 Merlin YES NO YES YES NO NO 206 410 820 See see se
21. 8 of its Rules The FCC requires that the manufacturer provide you with the following information FCC Regulations and Warranty F 1 F 2 1 Connection and Use with Nationwide Telephone Network The FCC requires that you connect your telephone equipment to the nationwide telephone network through a modular telephone outlet or jack The modular telephone outlet or jack to which the equipment must be connected is USOC RJ11C If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required If advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact your dealer for repair and or warranty information If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved Registered equipment may not be used on telephone company Coin Telephon
22. CTS D C 0 REMOTE OPEN BUTTON DOOR AJAR SWITCH DO DOOR BELL BUTTON su SPEAKER DOOR LATCH CONTACTS P J TO TO 12VAC CENTRAL HOST 0H2 OFFICE SYSTEM DO SERIAL NO MEN NE RJ11 CONNECTORS TERMINAL STRIP REMOVABLE 14 POSITION Figure 2 1 Door Phone Controller Back Panel Connections Prior To Installation NOTE Consider the following items before installation 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations 3 Never touch uninsulated telephone wires or terminals un less the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying telephone lines 2 8 Installation Procedures AT amp T Door Phone Controller Location You need to determine exactly where you want the unit installed and how you want it configured Another consideration is what components will be used with the AT amp T Door Phone Controller Here are some questions that must be answered prior to installation B Do you currently have a door speaker installed Do you have a business telephone system PBX or EKTS m Do you have a remote door unlock mechanism electric door strike installed B Do you have an auxiliary alert system door chime currently installed m Do
23. Controller using the information supplied in and the diagram in For Complete information regarding ground start installations also see Figure 4 2b each DIP switch position can be found in Installation Dedicated Trunk Port 4 3 AT amp T DOOR PHONE CONTROLLER BACK PANEL TERMINAL BLOCK HARD WIRE CONNECTOR NOT USED TO DOOR SPEAKER TO DOOR BELL BUTTON TO DOOR AJAR SWITCH TO REMOTE DOOR OPEN SWITCH OPTIONAL TO DOOR STRIKE PLATE DEVICE TO AUXILIARY ALERT DEVICE DOOR BELL CHIME TELEPHONE SYSTEM TRUNK PORT STATION www TO C O TRUNK PORT NOTE For Ground Start installations see Figure 4 2b TO C O STATION f wawa Figure 4 2a Connecting Door Phone Controller to Standard Telephone Equipment 4 4 Installation Dedicated Trunk Port TO AT amp T DOOR PHONE CONTROLLER J1 CONNECTORS TO SHIELD TERMINAL 12 ON AT amp T DOOR PHONE CONTROLLER jt TELEPHONE SYSTEM GROUND TERMINAL d TRUNK PORT STATION j sss TRUNK PORT TRUNK PORT STATION wa PORT NOTE For Ground Start installations TELEPHONE SYSTEM Connect the green wire to Tip and the red wire to Ring ry Figure 4 2b Ground Start Installations Installation Dedicated Trunk Port 4 5 Option Selection Refer to Appendix for a The final step of the installation procedure is selecting options detailed explanation of each of for your AT amp T Door Phone Controller The selec
24. Out Reset Options to Factory Defaults Phone Number Storage Memory 1 Phone Number Storage Memory 2 Door Phone Controller Option Selection To Select Options 1 Set DIP switch location 8 to the ON position 2 Dial door speaker phone number or extension 3 Dial 3 4 Program any or all of the following functions in any order Mode Option Verify To Select Option To Verify To Select Option To Verify To Verify To Verify To Verify To Select Option To Verify To Select Option To Verify To Verify To Verify To Select Option To Verify To Select Option To Verify Press To Select Option To Select Option To Select Option To Select Option To Select Option Listen For Single Beep Single Beep Press seconds of delay after strike plate release stops until Door Phone Controller calls back to indicate that door is ajar 24 for 2 sec on 4 sec off cadence or 15 for 1 sec on 5 sec off cadence 00 to 99 0 to 99 second s ring chime 4 digits first digit must be 0 3 4 5 6 7 or 8 remaining digits can be set from 0 to 9 00 to 99 door lock active time in sec Enable door code Disable door code For callback after strike plate release only For callback anytime door is opened 010 to 255 unit disconnects in 10 to 255 sec to restore factory default conditions 0 to 20 numerical digits and 2 second pause
25. T amp T Door Phone Controller DIP switch see to the ON position 2 Once the DIP switch has been set you must make con nection to the door speaker by calling the extension number assigned to the Door Phone Station Port At this point you must enter 3 on the telephone keypad option selection mode is active as soon as you hear a dial tone Any or all options may be 3 Use Table 5 1 to make each option selection reselected in any order The Forced Disconnect 4 To exit option selection mode press 3 on the Caney telephone keypad You will hear 2 beeps Hang up the when setting options unless 2 minutes elapse without a TOUS 5 Set position 8 of the AT amp T Door Phone Controller DIP switch back to the OFF position phone 5 6 Installation Dedicated Station Port Table 5 1 AT amp T Door Phone Controller Option Selection Information Options Delay Before Door Ajar Call back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults Phone Number Storage Memory 1 Phone Number Storage Memory 2 Mode Option Verify To Select Option To Select Select Select Select Select Select Select Select Verify Press Listen For Beep Press 000 to 255 for 0 to 255 seconds of delay after strike plate
26. a door unlock function This option provides the choice of either having the Door Ajar call back any time the door is opened or only after it has been opened via the strike plate release Note When the Door Ajar switch senses that the door has been opened and closed again the door open relay will cease being energized This option sets the maximum time in which two way communications can take place between the door speaker and the telephone Setting this option to less than 30 seconds is not advised Option Selection Mode Definitions B 1 Reset Option Selections to Factory Defaults Phone Number Storage Memory 1 Phone Number Storage Memory 2 Delay Before Door Ajar Call Back This option is useful when current option selections are unknown Note that this function will reset the Door Unlock Code to the default value but it will not reset Phone Number Storage Memory 1 or Phone Number Storage Memory 2 see below Defaults to dialing phone number 1 This option is used in what is called Ringdown Mode to auto dial a particular extension or outside line phone number The AT amp T Door Phone Controller has two memory locations for holding user stored telephone numbers Phone numbers can be for telephones within the same building or off premises These memory locations are used exclusively in Ringdown Mode Only one memory location is active at a time To select the active location for the phone number a telephone conn
27. apse without a phone 5 Set position 8 of the AT amp T Door Phone Controller DIP switch back to the OFF position Installation Dedicated Trunk Port 4 7 Operation Basic Door Answer Function Table 4 1 AT amp T Door Phone Controller Option Selection Information Mode Option Options Verify cadence Delay Before To Select Option 00 Single 000 to 255 for 0 to 255 Double 30 sec Door Ajar seconds of delay after strike Beep Call back To Verify 01 plate release stops until AT amp T Door Phone Controller calls back to indicate that door is ajar Ring Chime To Select Option Single 24 for 2 sec on 4 sec off 2 sec Cadence Beep cadence or Beep 4 sec To Verify 15 for 1 sec on 5 sec off Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults Select Option Select Option Select Option Select Option Select Option Select Option Select Option NI e 71 Single Beep Single Beep Single Beep Single Beep Single Beep Single Beep Single Beep 00 to 99 0 to 99 second s ring chime 4 digits first digit must be 0 3 4 5 6 7 or 8 remaining digits can be set from 0 to 9 00 to 99 door lock active time in sec 1 Enable door code O Disable door code For callback after strike plate release only For callbac
28. be provided on an exchange basis If AT amp T determines that the product cannot be replaced AT amp T will refund the purchase price to you If you purchased the product directly from AT amp T AT amp T will perform warranty repair on your premises in accordance with the terms and conditions of AT amp T s Business Day or Around the Clock warranty plans The details of AT amp T s warranty plans may be obtained from AT amp T If you purchased the product from an authorized dealer you will be covered by AT amp T s authorized dealer warranty plan during the warranty period Contact your authorized dealer for details of AT amp T s authorized dealer warranty plan AT amp T s obligation to repair replace or refund as set forth above is your exclusive remedy The limited warranties provided above do not cover damages defects malfunctions or product failures caused by W Failure to folow AT amp T s installation operation or maintenance instructions W Unauthorized modification or alteration of the product or its components m Product abuse misuse or the negligent acts of persons not under the reasonable control of AT amp T m Actions of third parties and acts of God other than power surges e g lightning FCC Regulations and Warranty F 3 F 4 This limited warranty applies only to the product purchased directly from AT amp T or purchased directly from an authorized AT amp T dealer This limited warranty does not apply to
29. cal wiring For the electric strikeplate a low voltage device 24 volts or less is recommended This section provides instructions for installing your AT amp T Door Phone Controller Provided are installation instructions for an optional electric door strike plate door ajar contacts and an auxiliary alert device These optional components must be installed prior to the installation of your AT amp T Door Phone Controller Refer to the respective installation manuals for specific mounting and wiring instructions The flow chart provided in will help direct you to the next appropriate section for attaching the AT amp T Door Phone Controller to the telephone equipment in your home or business also see Compatibility Chart on Inside the AT amp T Door Phone Controller shipping carton you will find B Ihe AT amp T Door Phone Controller unit Mounting template along the edge of the Tear out Reference Card Power cord and attached transformer Two mounting screws Two 6 conductor modular to modular 6 foot long cables Terminal strip connector Instruction Manual this manual Door Phone Controller Back Panel Connections The 14 contact terminal strip can be unplugged from the back panel 2 6 Installation Procedures The AT amp T Door Phone Controller back panel see has two RJ11 modular connectors and one 14 contact hard wire terminal strip These connections provide B Auxiliary Alert Contacts 2 output to
30. connected to the AT amp T Door Phone controller and then dials the desired phone number This is normal procedure for placing an outside call To initiate a call through the C O in the Port Saver Mode the person within the building simply takes the telephone off hook then accesses the trunk connected to the AT amp T Door Phone Controller At this point the caller will hear a dial tone from the Door Phone Controller Dialing a 9 or waiting 4 seconds will switch the caller to the C O and the regular phone number is dialed Installation No Dedicated Trunk Station Port 6 11 Troubleshooting and Maintenance 7 Troubleshooting and Maintenance 7 1 Troubleshooting Procedures Table 7 1 Troubleshooting Procedures Trouble Possible Cause LED off constantly Check power connection Brown out condition or software frozen LED on constantly Internal software error may still Work LED blinking more than four times a second Volume control turned down or DIP switches incorrectly set for mode of operation Talkback volume but no speaker volume Speaker volume but no talkback volume Shorted or open speaker lead connection No page or talkback volume Check forced disconnect time out selection Unit disconnects after a certain time Dial tone heard from the speaker of operation Telephone system returns dial tone after Door Phone goes on hook Cannot hear your own voice DIP switc
31. d has been spilled into the product 15 C If the product has been exposed to rain or water D If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged F If the product exhibits a distinct change in performance Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS General Information Please adhere to the following precautions 1 2 Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals un less the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines Installation Procedures 2 5 Introduction Contact a licensed electrician for installation of optional devices such as an electric strike plate and auxiliary alert device which may require electri
32. e Merlin II YES NO YES YES YES YES see see see Notes 4 5 9 Merlin YES NO YES YES NO NO Plus see see Notes 4 5 see Notes Merlin YES NO YES YES YES YES 1030 3070 see see see 4 5 9 System 25 YES YES YES YES YES YES see see Notes 1 4 see see see Note 1 see Not e 1 System 75 NO NO NO NO NO YES see System 85 NO YES NO NO YES YES see Note 14 see Note 4 Dimension NO YES NO NO YES YES see see Note 4 Horizon YES YES ES YES YES YES see see see Note 4 see Notes 4 6 7 see Comkey YES NO YES YES NO NO see Note 14 see see Note 4 see Note 4 Application Notes for Compatibility Chart When used in any mode of a System 25 if the user initi ates a call to the door and he wishes to enter the Option Selection mode pressing three pound keys fol lowed by the digit 3 i e 3 not 4 3 must be entered Actually the first does not seem to be recog nized at any time during the call However it should be noted that only 3 is needed to enter the Option Se lection mode when the call is initiated from the door button press When sharing a trunk port on a System 25 that port must be configured as an 805 PBX Centrex not an 801 Loop trunk This is the only way to transmit a hook flash to that port On the Merlin 1030 3070 tip and ring station application there is a preset delay such that the Merlin system will disregard DTMF for the first 12 seconds of the connec tion In this mode users have the choic
33. e Lines Equipment may be used with Party Lines in areas where state tariffs permit such connections and when equipment is adaptable for such use 2 Information You May Need to Supply the Telephone Company Upon request of your local telephone company you are required to provide them with the following information A The lines to which you will connect the telephone equipment B The FCC registration number and Ringer Equivalence Number REN Both numbers are listed on the equipment label The REN is useful to determine how many devices you may connect to your telephone line and still have them ring when your telephone line is called In most but not all areas the sum of all RENs per line should be 5 or less You may want to contact your local telephone company The local telephone company must also be notified upon final disconnection of the equipment from the local telephone company lines FCC Regulations and Warranty Warranty Information Limited Warranty and Limitation of Liability AT amp T warrants to you that the product will be free from defects in material and workmanship when title passes to you If you notify AT amp T that the product has failed to operate as warranted within one year of the date title passes to you AT amp T will at its option repair or replace the component or components of the product that failed to operate as warranted Any repair or replacement components may be new or refurbished and will
34. e back to the original call This feature operates much like a call waiting function 3 8 Installation Home Residential Telephone Line In Use With Door When Incoming Call Arrives If there is a call in progress between the door speaker and a person inside the building and a C O call comes in the person inside the building not the door speaker will hear a call waiting tone The person inside the building can hook flash the phone or dial 9 and communicate with the incoming caller When the call is complete the person inside the building hangs up the phone or to speak with the person at the door speaker again the person inside the building must hook flash the phone within 4 seconds after picking up the receiver Installation Home Residential 3 9 Installation for Telephone System With Available Dedicated Trunk Port 4 Installation Dedicated Trunk Port 4 1 Overview This section provides installation and operation information for installations with a telephone system that has an available Dedicated Trunk port DIP Switch Selections Complete information about the To customize the AT amp T Door Phone Controller to your specific DIP switch settings can be installation and option requirements you must properly set the found in Appendix A 8 position DIP switch located on the AT amp T Door Phone Controller front Panel see ZN CAUTION Do not connect to the modular jacks on the AT amp T Door Pho
35. e of either changing that time period or waiting for it to time out for each call In general the ring cadence option selection applies only if there is an auxiliary alert device connected All of the EKTS PBX s will absorb the ringing signal from the AT amp T Door Phone Controller and generate their own ring cadence to the telephone sets When using the AT amp T Door Phone Controller in any con figuration with a Merlin System the pound key must be pressed twice for each pound sent to the unit when dialing from a multi button set Port Saver Trunk Saver operation will not work for Tip Ring sets A switch hook flash is not passed to the trunk port from these sets A trunk shared with the AT amp T Door Phone Controller should not be placed in a trunk pool with other trunks When the AT amp T Door Phone Controller shares a C O trunk Trunk Saver operation is recommended Application Notes for Compatibility Chart continued 10 11 12 13 14 Tip Ring telephone sets connected to the Merlin System through a BTMI cannot use Port Saver Trunk Saver op eration The BTMI will not transmit the required hook flash signal System 75 requires a pound to be dialed at the end of every dial string This is required to send the dialed number to the trunk port Tip Ring telephone sets cannot be used in this mode to access the AT amp T Door Phone For PARTNER telephone sets not equipped with a Re call b
36. e risk of fire electric shock and injury to persons including the following 1 2 Read and understand all instructions Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings in the cabinet and the back or bot tom are provided for ventilation To avoid overheating these openings must not be blocked or covered The openings should never be blocked by placing the product on the bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home con sult your dealer or local power company Installation Procedures 2 3 2 4 Installation Procedures 8 INWARNING RISK OF ELECTRICAL SHOCK 11 12 13 EQUIPMENT MUST BE PROPERLY GROUNDED Your AT amp T equipment requ
37. ection to the AT amp T Door Phone Controller must be made by calling the extension number of the Door Phone Once connected dial in 1 this selects Memory Location 1 if you were to dial in 2 you would select Memory Location 2 See above explanation This option determines the length of time allowed for the door to shut after it has been opened by the strike plate release If the door is still ajar at the end of this period the controller will call back and an alarm tone will be heard in the receiver when the phone is answered B 2 Option Selection Mode Definitions Appendix C Specifications Electrical Standards Electrostatic Discharge Power Supply Page and Talk Back Amplifier Auxiliary Alert Door Latch Contacts The Door Answer Controller meets B UL listing requirements m F C C part 15 class B requirements B F C C part 68 requirements Your AT amp T Door Phone Controller complies with the ESD requirements in BELL Pub 48002 All user accessible connectors and controls have electrostatic discharge protection The AT amp T Door Phone Controller is powered by an UL listed wall mount transformer with a strain relieved cord It functions over an input power range of 96 VAC to 129 VAC Your AT amp T Door Phone Controller has a green LED power indicator B A flashing state of 2 5 per second indicates normal power to the unit and normal microprocessor operation A constant ON s
38. ed Wire Position 3 Green Wire Position 4 Yellow Wire Place one modular plug into modular jack on alerter SIGNAL Place the second modular plug into the WP91683 L1 Power Supply jack marked POWER Plug WP91683 L1 Power Supply into wall receptacle Test to see that external alert is operating by pressing the button on the AT amp T Door Phone Speaker E 2 Auxiliary Alert Device Connections AT amp T DOOR PHONE CONTROLLER BACK PANEL y 12VAC jo 60Hz CENTRAL 1AMP OFFICE TO HOST SYSTEM O SERIAL NO W TSS 2 PAIR DIW OR EQUIVALENT 22 26 AWG YELLOW E wi AT amp T AUXILIARY ALERT DEVICE 48VDC DW4A CORD OR EQUIVALENT EXTERNAL WP 91683 LI ALERT T DW4A CORD SIGNAL POWER CONTROL OR EQUIVALENT PEC 60314 COMCODE 405712928 Figure E 1 Connections For Auxiliary Alert Device Auxiliary Alert Device Connections E 3 Appendix F FCC Regulations and Warranty FCC Regulations Pertaining to this Equipment FCC PART 15 Radio Frequency Interference FCC PART 68 The AT amp T Door Phone Controller generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturers instructions may cause interference to radio and television reception NOTE The AT amp T Door Phone Controller has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the
39. eive C O call waiting tone when accessing the Door Phone Controller but cannot dial and or hook flash to connect to call PBX does not relay the hook flash Cannot open door remotely Door Unlock option disabled using Touch Tone door or unlatch function Wrong Door Code Check all wiring from AT amp T Door Phone Controller to electric strike plate device see manufacturer s instructions Check all wiring from AT amp T Door Phone Controller to electric strike plate device also check operation of electric strike plate device see manufacturer s instructions Cannot open door remotely using remote door open button Jumper pins 8 amp 9 of terminal block Verify DIP switch positions Use in dedicated mode If error tone verify Door Open Code and Door Unlock enable option Disconnect wires from the terminal block Door Unlatch Contacts Use volt ohm meter to check continuity between NO and C terminals while activating Touch Tone door unlatch function If continuity test fails return AT amp T Door Phone Controller for repair Disconnect wires from the terminal block Remote Open Button and Door Unlatch Contacts Use volt ohm meter to check continuity between both wires from the remote open button while activating the button If continuity test of button is good button is OK Now reconnect button wires to Remote Button Contacts and check continuity of Door Unlatch Contacts between NO and C wh
40. erations as well as servicing the door DIP Switch Selections Complete information about the DIP switch settings can be found in To customize the AT amp T Door Phone Controller to your specific installation and option requirements you must properly set the 8 position DIP switch located on the AT amp T Door Phone Controller front panel see ANCAUTION Do not connect to the modular jacks the AT amp T Door Phone Controller until after the DIP switches have been properly set When using the Door Phone Controller with a small business or residential telephone equipment no PBX installed the DIP switches must be set as shown in all OFF 3 2 Installation Home Residential LEGEND 7 38933 NOTE The Forced Disconnect ON for Timeout option does not apply when DIP switch position 8 is ON Mode Only Option Selection Figure 3 1 Home Residential DIP Switch Settings Installation When moving the Door Phone Connect the Door Phone Controller using the information in Controller or adding or removing Refer to cables from the back panel unplug the transformer from 120V outlet Also unplug the terminal strip and modular phone connectors on the back panel Installation Home Residential 3 3 AT amp T DOOR PHONE CONTROLLER BACK PANEL TO ENTRAL HOST OFFICE SYSTEM TO DOOR SPEAKER TO DOORBELL BUTTON TO DOOR AJAR SWITCH TO REMOTE DOOR OPEN SWITCH
41. h incorrect in telephone ear piece Plugged wires into wrong jack Forced disconnect timeout set to low Station mode seizes line then disconnects before AT amp T Door Phone Controller is accessed Station line plugged into J2 Cannot access AT amp T Door Phone Controller in trunk saver mode J1 and J2 swapped Bad door ajar switch Getting door ajar callback when door is actually closed Open door ajar switch wiring 7 2 Troubleshooting and Maintenance DIP switches incorrect for mode Possible Solution If power connection is good then return for repair Unplug and plug back in Unplug and plug back in if problem continues return for repair Verify setting of controls and DIP switches Volume control turned down Verify setting Remove short or open Change time out option selection Verify Mode of operation Program telephone system for no dial tone on this extension Correct Correct Enter Option Selection Mode 3 and enter new Forced Disconnect Timeout Duration Correct move to J1 Check connections and correct if needed Fix or adjust Fix Table 7 1 Troubleshooting Procedures Continued Possible Cause Possible Solution Trouble Missing jumper on terminal block Getting door ajar callback when door ajar switch is not used Door Phone Controller optioned for dedicated mode instead of Trunk Saver or Port Saver Mode Rec
42. he back located on the AT amp T Door Phone Controller front panel see panel Use the Flow Chart in Figure 6 1 to properly set Complete information regarding each of the DIP switch positions the DIP switch can be found in Appendix A CAUTION Do NOT connect to the modular jacks on the AT amp T Door Phone Controller until after the DIP switches have been properly set Installation No Dedicated Trunk Station Port 6 3 AT amp T DOOR PHONE CONTROLLER BACK PANEL a 12 VAC Onc XA 2 i TERMINAL BLOCK HARD 1 AMP WIRE CONNECTOR SERIAL NO TO DOOR SPEAKER TO DOOR BELL BUTTON TO DOOR AJAR SWITCH TO REMOTE DOOR OPEN SWITCH OPTIONAL TO DOOR STRIKE PLATE DEVICE TO AUXILIARY ALERT DEVICE DOOR BELL CHIME TELEPHONE SYSTEM TO C O TELEPHONE LINE di TRUNK PORT STATION Wp one LOOP START PORT TO C O SEI TRUNK PORT STATION eem v Figure 6 2 Connecting the AT amp T Door Phone Controller to a Telephone System With Shared Trunk Port 6 4 Installation No Dedicated Trunk Station Port Option Selection The final step of the installation procedure is selecting options for your AT amp T Door Phone Controller The selection of these bids Birra options must be done while in the Option Selection Mode This detailed explanation of each of these options mode lets you control such things as Delay Before Door Ajar Call Back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door U
43. hone Controller Option Selection Information Mode Option Listen i Options Verify Default Delay Before To Select To Select Option 00 Single 000 to 255 for 0 to 255 Door Ajar Beep seconds of delay after strike Call back To Verify plate release stops until AT amp T Door Phone Controller calls back to indicate that door is ajar Ring Chime To Select Option Single 24 for 2 sec on 4 sec off Beep cadence or Cadence To Verify 11 15 for 1 sec on 5 sec off cadence Ring Chime To Select Option i 00 to 99 0 to 99 second s Duration ring chime To Verify Door Unlock To Select Option i 4 digits first digit must be Double Code 0 3 4 5 6 7 or 8 Beep To Verify 31 remaining digits can be set from 0 to 9 Door Unlock To Select Option i 00 to 99 door lock active Duration time in sec To Verify Enable Door To Select Option i Enable door code Double 1 Code Disable door code Beep Enabled To Verify 5 Door Ajar To Select Option i For callback after strike Double Mode plate release only Beep To Verify For callback anytime door is opened Forced To Select Option Select To Select Option i 010 to 255 unit disconnects Double 120 sec Disconnect in 10 to 255 sec Beep Time Out To Verify Reset Options To Select Option i to restore factory default to Factory conditions Defaults To Verify NOTE The Door Ajar Delay Option Selection will begin when the call to the door speaker is disconnected
44. hone or door bell chime the person inside the building can press the door unlock push button which will stop the ringing and will open the door This allows the door to be unlatched without the use of a phone Calling the Door Speaker To initiate a call to the Door Speaker the person inside the building simply takes the telephone off hook and accesses the trunk connected to the AT amp T Door Phone Controller Installation Dedicated Trunk Port 4 9 Installation for PBX Equipment With Available Station Port Installation Dedicated Station Port 5 1 Overview This section provides installation and operation information for installations which use on premise telephone system that has an available Dedicated Analog Station Port DIP Switch Selections Complete information about the DIP switch settings can be found in Use the flow chart in to properly set the DIP switch To customize the AT amp T Door Phone Controller to your specific installation and option requirements you must properly set the 8 position DIP switch located on the AT amp T Door Phone Controller front panel see A CAUTION Do NOT connect to the modular jacks on the AT amp T Door Phone Controller until after the DIP switches have been properly set When using the AT amp T Door Phone Controller with a telephone system which has an available dedicated station port set the DIP switch as shown in Prior to setting this DIP switch you must
45. ile activating remote door open button If continuity test fails return AT amp T Door Phone Controller for repair Troubleshooting and Maintenance 7 3 Table 7 1 Troubleshooting Procedures Continued Trouble Cannot open door remotely using either Remote Door Open Button or the Door Code Selected options are not operating as expected Maintenance Possible Cause Improper wiring to existing door strike device May be caused by improper connection and use of NO Normally Open NC Normally Closed and C Common door latch relay contacts especially when interfacing these contacts to existing door configurations Incorrect or inappropriate values were entered Possible Solution Verify all connections when connecting the door strike contacts on the AT amp T Door Phone Controller to existing door open buttons Make sure of the following 1 The NO and C contacts are connected in parallel to a normally open button 2 The NC and C contacts are connected in series to a normally open button Use Verify mode to confirm selected options without changing the values Carefully consider the consequences of options chosen Periodic maintenance is not required Units requiring repair are returned to AT amp T for service 7 4 Troubleshooting and Maintenance Appendix A DIP Switch Settings Setting the DIP Switch Positions NOTE All switches are OFF when shipped from the
46. ional presses on the door speaker push button will be ignored with the exception that a confirmation tone will still be sent to the speaker when the door button is pressed When a person inside the building hears the door bell chime sound he can simply respond by dialing the Door Phone Controller station number At this point the AT amp T Door Phone Controller will establish two way communications with the door speaker To open the door the person inside the building either enters the Door Code on the telephone s keypad or presses the customer provided door unlock push button Either of these actions will activate the customer provided electric door release As an alternative response to hearing the door bell chime the person inside the building can press the door unlock push button which will stop the auxiliary contacts and will open the door This allows the door to be unlatched without the use of a phone To initiate a call to the Door Speaker the person inside the building simply takes the telephone off hook and dials the station phone number of the door speaker Ringdown Mode Basic Door Answer Function Visitor Presses Door Speaker Button When a visitor presses the door speaker push button the AT amp T Door Phone Controller will activate a door bell chime optional go off hook and dial the pre selected stored phone 5 8 Installation Dedicated Station Port number 1 or 2 these can be selected by pressing 1
47. ires a properly grounded three prong power receptacle for safe operation Have the receptacle checked by a qualified electrician before connecting this equipment Do not cut or remove the third ground prong from the power transformer Do not use two prong extension cords or adapters to defeat the safety features of this equipment If you have a two prong receptacle it must be replaced with a three prong receptacle installed by a qualified electrician Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by per sons walking on it Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product To reduce the risk of electric shock do not disassemble this product but take it to a qualified serviceman when some service or repair work is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used Unplug this product from the wall outlet and refer servic ing to qualified service personnel under the following conditions A When the power supply cord or plug is damaged or frayed B If liqui
48. k anytime door is opened 010 to 255 unit disconnects in 10 to 255 sec to restore factory default conditions 30 sec Double Beep Double Beep Double Beep Double Beep Double Beep Double Beep Double N A Beep 6736 OPEN 4 sec Enabled 120 sec NOTE The Door Delay Option Selection will begin when the call to the door speaker is disconnected 4 8 Installation Dedicated Trunk Port Visitor Presses Door Speaker Button When a visitor presses the door speaker push button the AT amp T Door Phone Controller will signal the telephone equipment inside your building to ring and activate a door bell chime optional Any additional presses on the door speaker push button will be ignored with the exception that a confirmation tone will still be sent to the speaker when the door button is pressed Answering a Call From the Door Speaker When a person inside the building hears the telephone ring and or the door bell chime sound he can simply respond by answering the ringing phone At this point the AT amp T Door Phone Controller will establish two way communication with the door speaker To open the door the person inside the building either enters the Door Code on the telephone s keypad or presses the door unlock push button Either of these actions will activate the customer provided electric door strike plate device As an alternative response to hearing the telep
49. mode DIP Switch Selections Complete information about the DIP switch settings can be found in To customize the AT amp T Door Phone Controller to your specific installation and option requirements you must properly set the 8 position DIP switch located on the AT amp T Door Phone Controller front panel see Use the flow chart in Figure 6 1 to help configure the DIP switch for either Trunk Saver or Port Saver Mode A trunk shared with the AT amp T Door Phone should never be configured in a telephone system with other trunks in a common pool or group 6 2 Installation No Dedicated Trunk Station Port LEGEND LOOP START The C O Trunk Saver Mode Immediately after cut thru Dialing Trunk to AT amp T Door Phone Controller 2 3335595 ON for i Option Selection __ Mode Only what do you want to be connected The DOOR Port Saver Mode 3 4 LOOP START i Figure 6 1 DIP Switch Setting for PBX With Shared Trunk Port Installation When moving the AT amp T Door Phone Controller or adding or removing cables from the back panel unplug transformer from 120V outlet Also unplug the Install the AT amp T Door Phone Controller using the information in Refer to To customize the AT amp T Door Phone Controller for this type of terminal strip and modular installation you must properly set the 8 position DIP switch phone connectors on t
50. n No Dedicated Trunk Station Port 6 7 Table 6 1 AT amp T Door Phone Controller Option Selection Information Mode Option Listen Verify For Delay Delay Before Door Ajar Call back Rine Chime Cadence Rine Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults To Select Option To Select Option 00 S To Verify To Select Option To Verify To Select Option To Verify To Select Option To Verify To Select Option To Verify To Select Option E To Verify To Select Option To Verify To Select Option 60 To Verify To Select Option To Verify 000 to 255 for 0 to 255 seconds of delay after strike plate release stops until AT amp T Door Phone Controller calls back to indicate door is ajar 24 for 2 sec on 4 sec off cadence or 15 for 1 sec on 5 sec off cadence 00 to 99 0 to 99 second s ring chime 4 digits first digit must be 0 3 4 5 6 7 or 8 remaining digits can be set from 0 to 9 00 to 99 door lock active time in sec Enable door code Disable door code For callback after strike plate release only For callback anytime door is opened 010 to 255 unit disconnects in 10 to 255 sec to restore factory default conditions Listen For Double Beep Double Beep Default Enabled 120 sec NOTE The Door Ajar Delay Optio
51. n Port 6 9 Calling the Door Speaker From Inside the Building Your PBX must be capable of relaying the hook flash from the station set to the trunk port To initiate a call to the door in the Trunk Saver mode the person within the building simply takes the telephone off hook accesses the trunk connected to the AT amp T Door Phone Controller and hook flashes the telephone within the first 5 seconds At this point there will be direct two way communication from within the building to the door speaker To initiate a call to the door in the Port Saver mode the person within the building simply takes the telephone off hook accesses the trunk connected to the AT amp T Door Phone Controller and dials 1 within the first 4 seconds At this point there will be direct two way communication from within the building to the door speaker Alternatively the person may dial a 9 within the first 4 seconds after accessing the trunk in order to be immediately connected to the C O line Telephone Line In Use When a Visitor Presses Door Speaker Button Once the doorbell push button is pressed you can Hook Flash to the door speaker and then back to the original call only once unless the push button is pressed again If you forget to hook flash back to the original call the AT amp T Door Phone Controller will call you back If a visitor presses the door speaker button while an existing call is already taking place o
52. n Selection will begin when the call to the door speaker is disconnected 6 8 Installation No Dedicated Trunk Station Port Operation Basic Door Answer Function Visitor Presses Door Speaker Button When a visitor presses the door speaker push button the AT amp T Door Phone Controller will signal the telephone equipment inside your building to ring and activate an auxiliary alert door bell chime optional Any additional presses on the door speaker push button will be ignored with the exception that a confirmation tone will still be sent to the speaker when the door button is pressed Answering a Call From the Door Speaker When a person inside the building hears the telephone ring and or the door bell chime sound he can respond by answer ing the ringing phone At this point the AT amp T Door Phone Controller will establish two way communication with the door speaker To open the door the person inside the building either enters the Door Code on the telephone s keypad or presses the customer provided door unlock push button Either of these actions will activate the customer provided electric door strike plate device As an alternative response to hearing the telephone or door bell chime the person inside the building can press the door unlock push button which will stop the ringing and will open the door This allows the door to be unlatched without the use of a phone Installation No Dedicated Trunk Statio
53. n the line the AT amp T Door Phone Controller will generate a door alert signal to indicate a visitor needs attention at the entrance The person using the line can hook flash the phone and be in direct two way communication to the door speaker The other party will be placed on hold At this point normal AT amp T Door Phone Controller functions can take place When the door phone functions have been completed i e door has been remotely opened hook flashing phone again or pressing 9 will return line to original call This feature operates much like a call waiting function 6 10 Installation No Dedicated Trunk Station Port Telephone Line In Use With Door When a Call Arrives If there is a call in progress between the door speaker and a station user and a call C O comes in the person inside the building not the door speaker will hear a call waiting tone The station user can hook flash the phone or dial 9 and communicate with the incoming caller When the call is complete the station user hangs up the phone To speak with the door phone again the station user must either hook flash the phone within 4 seconds of picking up the receiver if installed for Trunk Saver Mode or dial 1 if installed for Port Saver Mode Placing a Call Through the C O From Inside Building To initiate a call through the C O in the Trunk Saver Mode the person within the building simply takes the telephone off hook accesses the trunk
54. n this manual Then proceed with the necessary installation and option selection requirements NOTE If you are installing the AT amp T Door Phone Controller into a typical Home Residential environment no PBX refer to now REFER TO SECTION 3 RESIDENTIAL INSTALLATION you have Business REFER TO Teepnone SECTION 4 System PBX WITH DEDICATED TRUNK PORT Spare Trunk Port SECTION 5 PBX WITH STATION PORT Spare Station Port Available REFER TO SECTION 6 You must refer to your telephone system PBX WITHOUT DEDICATED owner manual for description of this TRUNK OR STATION PORT port Figure 2 9 Configuration of Telephone Equipment Flow Chart 2 22 Installation Procedures Installation for Home Residential Trunk Saver Mode Loop Start 3 Installation Home Residential 3 1 Overview You may also use the AT amp T Door Phone Controller with a dedicated phone This section provides installation and operation information for applications such as residences or small businesses which do not have a telephone system When your AT amp T Door Phone Controller is installed with standard telephone equipment no PBX the unit may operate in Shared Line Mode which permits a single telephone set to be shared between the AT amp T Door Phone Controller and an outside line to a Central Office Thus the standard telephone equipment can be used for normal call op
55. nch Exchange or communications system to alert personnel within a residence or building that someone is requesting attention at the entrance Operating the unit is simple when the push button on the door speaker is pressed the AT amp T Door Phone Controller unit signals a telephone station s and can activate an auxiliary alerting device such as a door bell chime or tone generator within the home or building Upon hearing the ringing telephone and or alerting device answer the phone and have a two way phone conversation with the person at the door The person inside the building can also remotely unlock the door either by entering a numeric code Door Code on the telephone s touch tone keypad or by pressing a button Features Control for remote door unlocking Voice communications with door speaker s B Door ajar detect m interface for door bell chime or tone generator Selectable option functions from touch tone telephone Introduction 1 3 SPEAKER VOLUME TALK BACK VOLUME DIP SWITCH Figure 1 1 Front View of the AT amp T Door Phone Controller and Control Panel 1 4 Introduction Terms You Should Know AuxiliaryAlert A door speakers push button can activate a bell chime within the building Cadence Telephone Ringing cycle i e 2 second ringing 4 second no ringing C O line Central Office telephone line carrier into building EKTS Electronic Key Telephone System
56. nd installation Section 2 Installation provides important installation information This section has step by step procedures for connecting the AT amp T Door Phone Controller to such optional equipment as B Remote door unlocking devices B Door ajar switch Auxiliary alert device B Remote open button Section 2 also provides an easy to use flow chart which directs the installer to the next appropriate section depending on what type of telephone equipment residential PBX etc will be used along with your AT amp T Door Phone Controller Sections 3 through 6 after reading and the flow chart at the end of that section the installer is referred to one of these sections Depending on which section is referenced all the necessary programming switch setting and operating information will also be included provides troubleshooting tips for when installation is complete and the AT amp T Door Phone Controller is not operating correctly Tear out Reference Card at the end of this manual provides all the necessary option selection information along with complete DIP switch settings and their definitions The AT amp T Door Phone Controller The AT amp T Door Phone Controller provides multi functional control for communications to a dedicated door speaker unit and a remote door unlocking device The AT amp T Door Phone Controller see Figure 1 1 can be used alone or it can be used along with a PBX Private Bra
57. ne Controller until after the DIP switches have been properly set Use the Flow Chart in Figure When using the AT amp T Door Phone Controller with a telephone 4 1 to properly set the DIP system which has an available dedicated trunk set the DIP Ene switch as shown in Prior to setting this DIP switch you must know if the dedicated trunk is Loop Start or Ground Start this information can be obtained from your local telephone company 4 2 Installation Dedicated Trunk Port 4 5 6 7 8 SEGR LOOP START _ Jon 339 The C O A Trunk Saver Mode off On Immediately after cut thru ON for a Dialing Trunk to AT amp T Option Selection __ Door Phone Controller Mode Only what do you want to ibe connected The DOOR Port Saver Mode v 1 2 8 a L LOOP START E 3 Figure 4 1 DIP Switch Setting for PBX with Dedicated Trunk Port Installation When moving the AT amp T Door To customize the AT amp T Door Phone Controller use the Paane Con ras information supplied in and the diagram in removing cables from the back panel unplug dransioner For ground start installations also see Figure 4 2b 120V outlet Also unplug the phone connectors on the back panel terminal strip and modular corda Install tte AT amp T Door Phone
58. nlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults Installation No Dedicated Trunk Station Port 6 5 Port Saver or Trunk Saver Mode Installation Port Saver Mode Any or all options may be reselected in any order The Forced Disconnect Time out option does not apply when setting options unless 2 minutes elapse without a Touch Tone selection Refer to the following instructions for Port Saver Mode or Trunk Saver Mode installation Follow the steps below to set the AT amp T Door Phone Controller for Port Saver Mode N CAUTION Never connect an AT amp T DOOR PHONE CONTROLLER with the DIP Switches optioned for TRUNK access to a STATION LINE Doing so may cause damage to the STATION LINE and or the AT amp T DOOR PHONE CONTROLLER Select Option Selection Mode by setting position 8 of the AT amp T Door Phone Controller DIP switch see Figure 1 1 to the ON position Access the trunk allocated for the AT amp T Door Phone Controller and make connection to the door speaker by dialing 1 or 2 within 4 seconds At this point you must enter 3 on the telephone keypad Option Selection Mode is active as soon as you hear a distinc tive dial tone if you don t hear a distinctive dial tone check to see if switch 8 is DOWN Use Table 6 1 to make each option selection To exit Option Selection Mode press 3 on the telephone keypad Y
59. oller is shipped with a keyhole mounting template and mounting screws Follow the steps below to mount the Door Phone Controller to a wall When moving AT amp T Door 1 Place template tear out page at end of manual over PO desired wall mounting location and mark screw positions removing cables from back Li gi transformers 2 Use a Philips screwdriver to screw each of the two Oullet screws into the marked screw positions Also unplug the terminal strip IMPORTANT Do not drive screws all the way into and modular phone connectors wall adequate space 5 16 must be left to position an Ne Panel the AT amp T Door Phone Controller bottom panel keyholes over screw heads 3 Mount the AT amp T Door Phone Controller over the protrud ing screw heads and seat unit firmly to the wall See ZN WARNING RISK OF ELECTRICAL SHOCK EQUIPMENT MUST BE PROPERLY GROUNDED Your AT amp T equipment requires a properly grounded three prong power receptacle for safe operation Have the receptacle checked by a qualified electrician before connecting this equipment Do not cut or remove the third ground prong from the power transformer Do not use two prong extension cords or adapters to defeat the safety features of this equipment If you have a two prong receptacle it must be replaced with a three prong receptacle installed by a qualified electrician Installation Procedures 2 11 4 When the AT amp T Door Phone Controller is securely m
60. oor is ever opened and the Door Ajar Call back time out has elapsed the Door Phone Controller will call back the phone chime for the duration of the ring chime duration and then repeat after the Door Ajar Call back time out has elapsed again If the phone is answered during that time a Door Ajar Tone will be heard The Door Ajar Tone will cease when any DTMF digit is pressed or the user speaks or hangs up Speaker Volume Control You can adjust the volume level of the door speaker by adjusting the Speaker Volume Control on the Door Phone Controller front panel see Talk Back Volume Control You can adjust the volume level from the door speaker to an inside telephone extension by adjusting the Talk Back Volume Control see 2 20 Installation Procedures LED When the AT amp T Door Phone Controller is powered on and functioning normally the LED should continually blink 2 5 times a second If there is a malfunction the LED will blink faster than 4 times a second see section or go out completely If the LED is not lit check power to unit first before calling for repair Installation Procedures 2 21 Connecting the AT amp T Door Phone Controller to Your Telephone Equipment Use the flow chart in Figure 2 9 to assist in configuring the AT amp T Door Phone Controller to your residential or business type telephone equipment Answer each appropriate question in the flow chart and refer to the section specified withi
61. optional door bell chime device B Door Latch Contacts 3 output to an electric door strike B Remote Open Button Contacts 2 input from a remote inside door open button Door Ajar Switch Contacts 2 input from door ajar device Door Bell Button Contacts 2 input from door bell chime button Shield Contact 1 used for shielding audio speaker wires Speaker Contacts 2 provides audio connection to door speaker s Host system RJ11 J1 Host modular jack interface This jack is provided for connection to your own telephone set or business telephone system PBX or EKTS the host system Central Office RJ11 J2 modular jack interface This jack is provided for connection to a C O telephone line from telephone company s central office ZN WARNING RISK OF ELECTRICAL SHOCK EQUIPMENT MUST BE PROPERLY GROUNDED Your AT amp T equipment requires a properly grounded three prong power receptacle for safe operation Have the receptacle checked by a qualified electrician before connecting this equipment Do not cut or remove the third ground prong from the power transformer Do not use two prong extension cords or adapters to defeat the safety features of this equipment If you have a two prong receptacle it must be replaced with a three prong receptacle installed by a qualified electrician Installation Procedures 2 7 AT amp T DOOR PHONE CONTROLLER BACK PANEL law ALERT CONTA
62. or 2 once connection to the speaker has been made Any additional presses on the door speaker push button will be ignored while the Door Phone Controller is off hook Answering a Call Sent When a person answers the ringing telephone the Door Phone From the Door Phone Controller will establish two way communications with the door speaker To open the door the person inside the building either enters the Door Code on the telephone s keypad or presses the customer provided door unlock push button Opening door will terminate Either of these actions will close the metallic contacts which Station mode access activate the customer provided electric door release Calling the Door To initiate a call to the Door Speaker the person inside the Speaker building simply takes the telephone off hook and dials the station phone number of the door speaker Installation Dedicated Station Port 5 9 Installation for Telephone System Without Available Dedicated Trunk or Station Port Installation No Dedicated Trunk Station Port 6 1 Overview Ground start trunks will NOT operate properly with this shared trunk installation This section provides installation and operation information for installations which use a telephone system that does not have an available Dedicated Trunk or Station Port By configuring the telephone system to the instructions in this section your telephone system equipment will operate in Trunk Port share
63. ou will hear 2 beeps Hang up phone Set position 8 of the AT amp T Door Phone Controller DIP switch back to the OFF position 6 6 Installation No Dedicated Trunk Station Port Trunk Saver Mode Follow the steps below to set the AT amp T Door Phone Controller for Trunk Saver Mode N CAUTION Never connect an AT amp T DOOR PHONE CONTROLLER with the DIP Switches optioned for TRUNK access to a STATION LINE Doing so may cause damage to the STATION LINE and or the AT amp T DOOR PHONE CONTROLLER 1 Select Option Selection Mode by setting position 8 of the AT amp T Door Phone Controller DIP switch see to the ON position Any or all options may be 2 Access the Trunk allocated for AT amp T Door Phone Con reselected in any order troller and make connection to the door speaker by Hook Flashing the phone At this point you must enter Tha Forced Disconnect 3 on the telephone keypad Option Selection Mode Time out option does not apply is active as soon as you hear a distinctive dial tone if when setting options unless 2 you don t hear a distinctive dial tone check to see if minutes elapse without a switch 8 is DOWN Touch Tone selection 3 Use Table 6 1 to make each option selection 4 To exit Option Selection Mode press 3 on the telephone keypad you will hear 2 beeps Hang up phone 5 Set position 8 of the AT amp T Door Phone Controller DIP switch back to the OFF position Installatio
64. ounted to the wall then all cables and wires can be connected to the terminal strip and then plugged into the back panel DOOR PHONE CONTROLLER BACK PANEL KEYHOLE MOUNTING 5 16 TYPICAL MOUNTING SCREWS Figure 2 3 Mounting AT amp T Door Phone Controller to Wall 2 12 Installation Procedures Connecting Door Speaker Door Button and Door Ajar Switch to the AT amp T Door Phone Controller Polarity of wires is not important Total wire length should not exceed 1500 feet Door Ajar switch should be closed when door is closed If a door ajar switch will not be used you must leave a jumper installed across the two Door Ajar Switch terminals 1 Use the diagram in Figure 2 4 and follow the steps below Run shielded twisted pair wires 22 24AWG from the Speaker terminals on the rear panel of the AT amp T Door Phone Controller 13 amp 14 to the installed Door Speaker 1 amp 2 Connect the shield to the Shield ter minal on the controller 12 Run 2 wires 22 24AWG from the Door Bell Button terminals 10 amp 11 to the door bell push button on the installed door speaker push button assembly 3 amp 4 Run 2 wires 22 24AWG from the optional Door Ajar Switch terminals 8 amp 9 to the installed door ajar switch Remote Door Open Switch optional A remote door open switch normally open contact provides additional means for opening an electric door opening device
65. re is used by the WP91683 L1 Power Supply to provide 48 Volts DC to activate the external alert device INSTALLATION These instructions apply to the use of a four conductor modular cord only 1 Locate the WP91683 L1 Power Supply as close as pos sible to the AT amp T Door Phone Controller the nearest wall receptacle DO NOT PLUG IN YET 2 Runa standard 2 pair wire DIW or equivalent between the AT amp T Door Phone Controller and a 103A connect ing block Connect jack on the 103A block to the jack Auxiliary Alert Device Connections 1 A standard 4 conductor modular 3 cord set can be used for limited distances 25 feet and under for connections between the WP91683 L1 Power Supply power jack and alerter signal only marked Control on the WP91683 L1 Power Supply with DW4A modular cords or equivalent see E 1 A Connect one end of the wire to the AT amp T Door Phone Controller as follows Connect the black and yellow leads to the Aux Alert terminals of the Door Phone Controller B Connect the other end of the wire to the 103A connecting block Connect the leads as follows On the 110 type connector connect Terminal 2 to the black wire and connect Terminal 6 to the yellow wire see Figure E 1 Place alerter where desired Run 2 pair DIW from alerter signal to power supply Connect 4 conductor modular plugs to both ends of 2 pair wire DIW as fol lows Position 1 Black Wire Position 2 R
66. release stops until AT amp T Door Phone Controller calls back to indicate that door is ajar 4 for 2 sec on 4 sec off cadence or 15 for 1 sec on 5 sec off cadence 00 to 99 0 to 99 second s ring chime 4 digits first digit must be 0 3 4 5 6 7 or 8 remaining digits can be set from 0 to 9 00 to 99 door lock active time in sec Enable door code Disable door code For callback after strike plate release only For callback anytime door is opened 10 to 255 unit disconnects in 10 to 255 sec to restore factory default conditions 0 to 20 numerical digits and 2 second pause terminates entry 0 to 20 numerical digits and 3 2 second pause terminates entry Listen For Default 1 Enabled 120 sec Double Beep Double Beep Beep Installation Dedicated Station Port 5 7 Operation Auxiliary Alert Mode Basic Door Answer Function Visitor Presses Door Speaker Button Answering a Call Sent From the Door Phone The telephone system must pass Touch Tones to the station port connected to the AT amp T Door Phone Controller in order for the Door Code to be recognized Complete installation instructions for adding an Auxiliary Alert option can be found in Calling the Door Speaker When a visitor presses the door speaker push button the Door Phone Controller will activate an auxiliary alert door bell chime Any addit
67. tate indicates a brown out condition or microprocessor failure A constant OFF state indicates there is no power to the unit Paging output power is 2 watts continuous 3 35 Vrms sine wave Talk back input sensitivity with 600 microVrms at the speaker leads tip and ring output level will be 17 dBm Relay Contact Closures rated at 1 amp Relay Contact Closures rated at 2 amps Specifications 1 Ring Generator C O Line Jack Mechanical Front Panel Back Panel Dimensions and Weight C 2 Specifications Your AT amp T Door Phone Controller provides a ring generator signal which can ring devices that respond to either 20 Hz or 60 Hz frequencies The ringer will automatically adapt to a 50 Hz line by ringing at 25 Hz A Ringer Equivalence REN of 2 is supported by the AT amp T Door Phone Controller Input has a REN of 0 5 Type B The AT amp T Door Phone Controllers control unit PCB is mounted in a molded plastic enclosure with a metal back panel The front panel is protected by a flip down cover You have access to controls and connections on the front panel and back panel The front panel controls and indicators consist of one page volume control one talkback volume control one 8 position DIP switch B one power indicator green LED The back panel connections consist of one strain relieved cord approximately 6 feet in length attached to a wall mount transformer B one RJ1
68. tion of these MESE options must be done while in the Option Selection Mode This mode lets you control such things as Delay Before Door Ajar Call Back Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Time Out Reset Options to Factory Defaults 4 6 Installation Dedicated Trunk Port Follow the steps below to select options for your AT amp T Door Phone Controller N CAUTION Never connect an AT amp T DOOR PHONE CONTROLLER with the DIP Switches optioned for TRUNK access to a STATION LINE Doing so may cause damage to the STATION LINE and or the AT amp T DOOR PHONE CONTROLLER 1 Select Option Selection Mode by setting position 8 of the AT amp T Door Phone Controller DIP switch to the ON position see 2 Once the DIP switch has been set you must make con nection to the door speaker by accessing the trunk connected to the AT amp T Door Phone Controller At this point you must enter 3 on the telephone keypad op tion selection mode is active as soon as you hear a distinctive dial tone Any Or MAY DE 3 Use Table 4 1 to make each option selection reselected in any order E The Forced Disconnect 4 To exit option selection mode press 3 on the Time out option does not apply leph ne k will hear 2 Han h when setting options unless 2 telephone keypad you ea beeps Hang up the minutes el
69. urity switch If this switch is ON any user can activate Option Selection Mode by keying in 3 on a touch tone telephone set which connects directly to the AT amp T Door Phone Controller When this switch is OFF Option Selection Mode cannot be activated Normal Mode OFF Option Selection Mode ON Appendix B Option Selection Mode Definitions Ring Chime Cadence Ring Chime Duration Door Unlock Code Door Unlock Duration Enable Door Code Door Ajar Mode Forced Disconnect Timeout The information below provides detailed information regarding each of the settable options for the AT amp T Door Phone Controller Provides an alternate ring on off cycle from how it would ring for a normal call For instance you can configure the telephone to ring for 2 seconds and then be silent for 4 seconds or ring for 1 second and then be silent for 5 seconds This option provides a maximum duration of telephone ringing cycles in seconds before the AT amp T Door Phone Controller will disconnect This option determines what your door unlock combination will be The default is set for 6736 but for security reasons it is recommended you change this to your own four number combination This option determines the amount of time the door unlock function will be activated The default is 4 seconds This option can be set so the door access code is disabled Once it is disabled entering the door unlock code will not provide
70. utton FEATURE 03 must be dialed to send a hook flash signal to the trunk port In the Ringdown mode no number should be pro grammed in the AT amp T Door Phone for it to dial when the door button is pressed The PARTNER Plus system should be programmed to alert the desired stations when the door phone goes off hook on its station port The information for this system is based on engineering judgment Contents Introduction 1 1 B Using This Manual 1 B Features B Terms You Should Know Installation Procedures 1 2 i 2 8 B Operation and Controls Information 2 20 B Connecting the AT amp T Door Phone Controller to Your Telephone Equipment 22 Prior to Installation Installation for Home Residential 3 1 vii Installation for Telephone Systems With Available 4 1 Dedicated Trunk Port Installation for Telephone Systems With Available 5 1 Station Port Installation for Telephone Systems Without Available 6 1 Dedicated Trunk or Station Port 7 Troubleshooting and Maintenance 7 1 B Troubleshooting Procedures 7 2 B Maintenance 7 4 viii gt DIP Switch Settings A g m Option Selection Mode Definitions B Specifications Using the AT amp T Door Phone Controller With an Answering Machine D 1 AT amp T Auxiliary Alert Option E FCC Regulations and Warranty F 1 Figures Introduction 1 1 1 1
71. you have a door ajar switch installed The AT amp T Door Phone Controller is designed to control the functions of the components mentioned above and how you answer these questions will determine how the AT amp T Door Phone Controller will be installed optioned and operated When selecting options for your AT amp T Door Phone Controller e g to change the door unlock security code the AT amp T Door Phone Controller unit must be DIP switch selected to Option Selection mode For this reason you may want to install the AT amp T Door Phone Controller unit in a secure area which has access only by authorized personnel If you are installing the unit in a business environment currently have PBX EKTS you may wish to install the unit along with the telephone equipment See for a typical installation diagram Installation Procedures 2 9 22 24 GAUGE WIRE AUX ALERT DEVICE AT amp T DOOR PHONE TELEPHONE EXTENSION CONTROLLER Secure Location DOOR AJAR SWITCH lt EXISTING 7 PHONE MODULAR LINES PHONE CABLE SHIELDED TWISTED PAIR SPEAKER TELEPHONE ATTENDENT WIRE Mis I 1 DOOR STRIKE 4 PLATE DEVICE Figure 2 2 Typical AT amp T Door Phone Controller Installation 2 10 Installation Procedures Installation Mounting Instructions The AT amp T Door Phone Controller can be placed on a flat table or shelf or mounted to a wall Wall Mount Instructions The AT amp T Door Phone Contr

Download Pdf Manuals

Related Search

Related Contents

PIS Divos 123  User Manual  leaflet MAH BRAND_PL 00006-0338  Telefonapp. NT343/346/366  Verbatim BD-R SL 4x 25GB Printable 25 Pack Spindle  PACSystems* RX3i CPU IC695CPE305 IPI  H.264 Video Compression    Hydro-DO Dissolved Oxygen Sensor - Sea    

Copyright © All rights reserved. Failed to retrieve file