ASUS V-Series P5G965 User's Manual
Contents
1. before reinstalling it to the chassis To do this i Locate the bay cover locks Press the locks outward to release the bay cover Push the bay cover inward then set it aside Follow the same instructions to remove the 3 5 drive bay cover To reinstall the front panel assembly and side cover xi Insert the front panel assembly hinge like tabs to the holes on the right side of the chassis Swing the front panel assembly to the left then insert the hooks to the chassis until the front panel assembly fits in place Insert the six side cover hooks into the chassis tab holes Push the side cover to the direction of the front panel uniil it fits in place Secure the cover with two screws you removed earlier Air duct Chassis tab holes RY Installation manual2. to the module retention module base Connect the CPU fan cable to the connector on the motherboard CAUTION Do not forget to connect the CPU fan connector Hardware monitoring error can occur if you fail to plug this connector CPU fan Retention bracket lock amp cpu fan connector CPU heatsink Retention module base Retention bracket Installation manual Installing a DIMM Locate the DIMM sockets in the motherboard 2 Unlock a DIMM socket by pressing the retaining clips outward Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket 4 Push the DIMM to the socket until the retaining clips snap inward CAUTION Unplug the power supply before adding or removing DIMMs Failure to do so may cause damage to the motherboard and or components A DDR DIMM is keyed with a notch so that it fits in only one direction Do not force a DIMM into a socket to avoid damaging the DIMM Installing an expansion card 1 Remove the metal cover opposite 2 Remove the metal bracket lock the slot that you intend to use 3 Insert the card connector to the slot then press the card firmly until it fits in place 4 Replace the metal bracket lock Installation manual Installing storage drives Optical drive 1 Place the chassis upright then remove the upper 5 25 drive bay metal plate cover 2 Insert the optical drive to the bay then carefully push the drive un
3. E2849 ASUS V Series ASUS PC Desktop Barebone Installation manual 860 7 Front panel features I o LI PW 5 25 inch drive f bay cover 3 5 inch drive bay Lio 9 cover Headphone port Microphone port mus USB 2 0 ports HDD LED Power button Reset button NOTE Some models 9 9 9 may have two additional Oe of lo 0 o S a USB 2 0 ports and or one A di IEEE 1394a port E Rear panel features D oe ONS NOTE The rear panel ports and their locations amp n A may vary depending on the model of your 2 7 r system For detailed descriptions refer to the Ip TESA system User Guide e t3 4 4 o We PS 2 keyboard port Pl o OG PS 2 mouse port ae m 7 VGA port lt a ala Parelel pot ERER SI USB 2 0 ports some models may TOO have four rear USB 2 0 ports XK E Po POSTI LAN RJ 45 port L O RR sont One of the following ports SII E SATA port Car Ce Ce EJO i Optical S PDIF Out port ID c C Coaxial S PDIF Out port I IEEE 1394a port IE some models only Installation manual 9 O
4. e cover aside 3 Locate the front panel assembly hooks then lift them until they disengage from the chassis 4 Swing the front panel assembly to the right until the hinge like tabs on the right side of the assembly are exposed 5 Remove the front panel assembly then set aside Air duct Installation manual Installing a CPU Installing an Intel Pentium 4 CPU in the LGA775 package Locate the CPU socket on the motherboard 2 Press the load lever with your thumb Retention tab A then move it to the left B until it is released from the retention tab CAUTION To prevent damage to the socket pins do not remove the PnP cap unless you are installing a CPU Load lever 3 Lift the load lever in the direction of the arrow to PnP cap a 135 angle 4 Lift the load plate with your thumb and forefinger to a 100 angle 4A then push the PnP cap from the load plate window to remove 4B Load plate 5 Position the CPU over the socket making sure that the gold triangle is on the bottom left J corner of the socket Fit the socket alignment key into the CPU notch Foi triangle 6 Close the load plate A then push the load lever B until it snaps into the retention tab Installation manual Installing an AMD CPU Locate the CPU socket then lift the socket lever to a 90 angle Install the CPU to the socket making sure that the CPU corner with the gold triangl
5. e matches the socket corner with a small triangle Push down the socket lever to secure the CPU CAUTION Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU Installing the CPU fan and heatsink assembly Installing an Intel Pentium 4 CPU heatsink and fan 1 Place the heatsink on top of the installed CPU making sure that the four fasteners match the holes on the motherboard Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place When the fan and heatsink assembly is in place connect the CPU fan cable to the connector on the motherboard Installation manual Installing an AMD CPU heatsink and fan 1 Place the heatsink on top of the installed CPU IMPORTANT Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base otherwise you can not lock the retention bracket Attach one end of the retention bracket to the retention module base Attach the other end of the retention bracket near the retention bracket lock to the retention module base until it clicks in place NOTE Your boxed CPU should come with installation instructions for the CPU fan heatsink assembly and the retention mechanism If the instructions in this section do not match the CPU documentation follow the latter Push down the retention bracket lock on the retention mechanism to secure the fan and heatsink
6. ne of the following audio ports configurations n HOO a C D 6 channel 0 8 channel ORO O KORO Refer to the configuration table in the User Guide for details Internal components Tm t gt 2 _C C In N 6 DO U N di il si N A co A lui 9 A n y of Y l at 1 Front panel cover 5 Power supply unit 2 5 25 inch optical drive bays 6 Chassis fan slot 3 Floppy disk drive bay 7 ASUS motherboard 4 Hard disk drive bay 8 Expansion slot metal brackets NOTE Refer to the system User Guide for motherboard details Installation manual Selecting the voltage The system s power supply unit has a 115 V 230 V voltage selector switch located beside the power connector Use this switch to select the appropriate system input voltage according to the voltage supply in your area If the voltage supply in your area is 100 127 V set the switch to 115 V If the voltage supply in your area is 200 240 V set the switch to 230 V NOTE Refer to the system User Guide for the exact location of the voltage selector Removing the side cover and front panel assembly 1 Remove the cover screws on the rear panel 2 Pull the side cover toward the rear panel until its hooks disengage from the chassis tab holes Set the sid
7. til its screw holes align with the holes on the bay 3 Secure the optical drive with two screws on both sides of the bay 4 Connect the IDE A and power B plugs to connectors at the back of the drive Floppy disk drive 1 Place the chassis upright then remove the lower 3 5 drive bay i metal plate cover 2 Insert the floppy disk drive to the bay then carefully push the drive until its screw holes align with the holes on the bay 3 Secure the floppy disk drive with two screws on both sides of the bay 4 Connect the signal A and power B plugs to connectors at the back of the drive Hard disk drive 1 Place the chassis upright then remove the upper 3 5 drive bay metal plate cover 2 Insert the hard disk drive to the bay then carefully push the drive until its screw holes align with the holes on the bay 3 Secure the hard disk drive with two screws on both sides of the bay Installation manual LI 00 000 Fy 000 o 290000080000 000 0090500 9980000009 O 00005000 00096000 10 For SATA HDD Connect the SATA signal and power plugs to the connectors at the back of the drive For IDE HDD Connect the IDE and power plugs to the connectors at the back of the drive Removing the bay covers and reinstalling the front panel assembly and side cover If you installed an optical and or floppy disk drive remove the bay cover s on the front panel assembly
Download Pdf Manuals
Related Search