ASA Electronics Voyager VOM78T User's Manual
Contents
1. Brightness and contrast controls Volume control Power stand by switch Audio video input and Audio output Tilt up down switch CONTENTS OF VOM 78T 7 Monochrome Monitor 1 7 monitor 1 Snap on sun visor 1 Monitor bracket 1 Power harness with locking connector 1 Range markers 4 Thumb screws M5 x 15 with plain washer amp spring washers 4 Attachment screws with washers M5 X 12 1 6 inches adaptor cable for non tilt camera use into CA1 input terminal VOM 78T 1 VOM 78T OPERATIONS MANUAL VEC 65 Cable 1 65ft cable with waterproof connector Not supplied VCT 655 Cable 1 65ft cable with waterproof connector for tilt camera Not supplied Documents 1 Operations manual BEFORE INSTALLATION 1 This system operates from 10 volts DC to 32 volts DC negative ground 2 Please install this system according to the instructions in this manual 3 DO NOT DISASSEMBLE THE CAMERA OR THE MONITOR Disassembling the camera will compromise the waterproof seal and this voids the Warranty 4 Connect the system to a switched ignition power source Connection to a non switched battery power source will reduce battery life WARNING 1 To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are potentially lethal voltages inside the monitor there are no serviceable parts inside if evidence of tampering is detected the warranty will be considered void 2 Keep monitor away from leak2. Cable bracket Machine screws Handle screws Sun visor Power cable Adaptor cable 6 DISCLAIMER The use of the VOYAGER Observation system does not guarantee or promise that the user will not be in an accident or otherwise not collide with an object The VOYAGER Observation system Is not intended in any way to be a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor safety regulations This product is not intended to be a substitute for rearview mirrors or for any other motor vehicle or boat equipment mandated by law Design And Specifications Are Subject To Change Without Notice 14 Voyager WARRANTY 90 DAY 12 MONTH LIMITED WARRANTY AUDIOVOX SPECIALIZED APPLICATION LLC the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 90 days from the date of original purchase such defect s will be repaired or replaced at the Company s option without charge for parts and repair labor After the initial 90 day period and for a period of 12 months from the date of original purchase the Company will supply atno charge a replacement for any defective part s To obtain repair or replacement within the terms of this warranty the end user should contact the O E M The product is to be delivered to the OEM or original pl
3. monitor camera switch settings are correct for your particular application 10 AUDIO JACK Connects audio connector to an optional external speaker 11 CA1 CA2 INPUTS JACKS In single camera applications the camera should be connected to CA 1 Monitor Input A Rear Back up Camera should be connected to CA 1 Monitor Input in any application Reverse trigger Feature Applying 12 Volts to Blue Reverse Trigger lead serves two functions 1 Monitor comes ON from Stand by mode and switches to CA1 input 2 Monitor Input will switch from CA2 to CA1 while 12 Volts is applied 6 Voyager VOM 78T OPERATIONS MANUAL AFFIXING DISTANCE MARKERS TO THE MONITOR SCREEN 1 Clean monitor screen surface of fingerprints Place distance indicators behind the vehicle at 3 feet 5 feet and 9 feet along the width of the vehicle These distances are measured from the rear bumper Refer to fig 5 2 Attach the markers to the monitor screen over the images of the distance indicators These markers represent distances of 3 feet 6 feet and 9 feet from the back of the vehicle See fig 5 3 Affix the STOP marker on the monitor screen over the image of the rear bumper to locate the rear bumper 4 The monitor screen is now calibrated for distances behind the vehicle of 3 feet 6 feet and 9 feet UE Ah gt STEEL PLATE FOR REINFORCEMENT OR OVERHEAD Le RECOMMENDED FOR SECURE MOUNTING FIGURE 1 VOM 78T 7
4. 2 switch CA1 used mainly for rear mounted camera as specified by the installer CA2 used mainly for side or mirror mounted camera or as specified by the installer Tilt up down switch Vertical angle or view adjusted into Up and Down posltions Day Night switch Pre set brightness and contrast levels optimized for day or night operation Contrast Variable control of contrast Should be adjusted if the DAY NIGHT switch does not achieve the most desirable picture Brightness Variable control of brightness Should be adjusted if the DAY NIGHT switch does not achieve the most desirable picture Volume Variable control of internal speaker volume FUNCTIONS AND OPERATION CONTINUED Rear of monitor See FIGURE 4 8 POWER CONNECTION PnNo erste 1 NN N C VOM 78T VOM 78T OPERATIONS MANUAL 9 MIR NOR OPTION MIRTINOR m Voyager Tilt camera VBCT 130 Monitor switch position in MIR position Voyager camera switch magnet in MIR position This combination will result in an inverted mirrored image that is correct for rear back up camera use If the opposite image is required for applications other then rear back up camera use either the monitor or the camera switch should be set to the NOR position n case VBCT 130 Tilt camera applied to CA1 position MIR NOR option can be selected only by the CA1 dip switch Make sure that
5. OBSERVATION OPERATION MANUAL SERVATION r OBSERVATION OBSERVATION OBSERVATION SYSTEM SERVATION VOM ST with tilt camera control OBSERVATION S ERVATION OBSERVATION ERVATION OBSERVATION SERVATION OBSERVATION S ERVATION OBSERVATION SERVATI Aupioyox RECIALIZED APPLICATIONS L 4 C VOM 78T Features Dual Camera input Tilt camera control Brightness Contrast Volume Day night Adjustment Control Audio output Automatic Trigger Operation Standby On Camera Switching Illuminated Front Panel Mirror Normal selectable www asaelectronics com VOM 78T OPERATIONS MANUAL IMPORTANT The VOYAGER Observation System has been designed to provide years of trouble free operation Please read this manual throughly This manual contains instructions to ease installation of the camera and monitor The VOYAGER Observation System is a supplement to standard rearview mirror systems and will provide additional rearview vision when installed and maintained properly The VOYAGER Observation System is not intended in any way to be a substitute for careful cautious defensive driving or for the consistent adherence to all applicable traffic laws and motor safety regulations This product is not intended to be a substitute for rearview mirrors or for any other motor vehicle or boat equipment mandated by laws FEATURES VOM 78T Monochrome 7 Monitor Day night switch
6. ROLS AND CONNECTIONS FIGURE 4 VOM 78T 11 VOM 78T OPERATIONS MANUAL 2 xL pra INDICATOR Ke ma WIDTH OF VEHICLE FIGURE 5 12 Voyager MARKERS EXAMPLE GR dO et Sei b i ei JU VOM 78T OPERATIONS MANUAL Operation Manual SPECIFICATIONS System Rated voltage Operating voltage Current consumption TV system Picture tube VOM 78T monitor Picture image Picture resolution Power connector Inputs Power requirements Power consumption Operating Temperature Range Storage Temperature Range 12 volt DC negative ground 10 to 32 volt DC 2 5 amperes EIA Black and White 7 inch picture measured diagonally 90 degree deflection angle Factory preset to reverse image 600 TV lines Red Positive input 10V to 32V Blue Reverse gear input 12V or 24V Black Ground 4 pin mini jack 1 Video input 1 0V p p Sync Negative 2 12V Tilt control power 1 only 3 Audio input 4 12V 0 2A DC output 5 Shield Ground 10V to 32V DC 20W Maximum 15 C to 50 C 5 F to 122 25 85 13F to 185 VOM 78T 13 VOM 78T OPERATIONS MANUAL Dimensions 200 W X 152 H X 220 D mm 7 9 W X 6 0 H X 8 7 D Inch Including projecting parts and controls Weight Approx 2 5 5 Ibs Including mounting bracket Accessories Supplied Mounting bracket Mounting bolts Machine screws Tapping screws Spring washers Flat washers 12X5 Flat washers 20X5
7. VOM 78T OPERATIONS MANUAL Unit Inch MONITOR MOUNTING HOLE PATTERN FIGURE 2 Voyager VOM 78T OPERATIONS MANUAL For Tilt Camera Installation in the CA1 Postion TO MONITOR CAMERA 1INPUT WATERPROOF CAMERA CONNECTOR LX GROMMET SEAL THOUGH VEHICLE EXTERIOR For Tilt Camera Monitor Installation with existing VEC65 cable installed TO VOM 78T VOM 783T Oum vss OY BIHA ON 5 ft p 6 n Er Tor 4 31100032 31100031 ADAPTOR CABLE EXISTING VEC 65 CABLE ADAPTOR CABLE For Non Tilt Camera Installation in the CA1 Postion TO MONITOR CAMERA 1 INPUT WATERPROOF CAMERA CONNECTOR 6 inches 65 ft PR ik CH 1 3 ADAPTOR CABLE GROMMET TO SEAL THOUGH VEHICLE EXTERIOR note The audio line will be used as the camera tilt line resulting in no Audio VOM 78T 9 VOM 78T OPERATIONS MANUAL REAR OF MONITOR TO MONITOR CONNECTIONS How to use the supplied bracket holder 10 Voyager RED To Power DC 10V or 32V BLK Ground BLUE Reverse Trigger Caution gt Before making the connections disconnect the ground terminal of the car battery to avoid short circuiting The plugs should be fully inserted into the connectors or jacks A loose connection may cause the unit to malfunction FIGURE 3 VOM 78T OPERATIONS MANUAL MONITOR FRONT VIEW MONITOR BACK VIEW MONITOR OPERATING CONT
8. ace of purchase with proof of warranty coverage e g dated bill of sale and serial number of the unit and vin specification of defect s transportation prepaid to an approved warranty station This warranty does not extend to the elimination of externally generated static or noise to the correction of antenna problems to costs incurred for removal or reinstallation of the product or to any damage to any tapes speakers accessories or electrical systems This warranty dose not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect accident THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANTY S LIABLITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER FOR THE PRODUCT This warranty isin lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY SHALL BE LIMITED TO THE DURATION OF THIS WARRANTY ANY ACTION FOR BREECH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 DAYS FROM THE DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREECH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER No person or representative is authorized to assume
9. for the Company any liability other that expressed herein in connection with the sale of this product Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state AUDIOVOX SPE CIALIZED APPLICATIONS LLC Visit us at www asaelectronics com Printed In China
10. ing water rain moisture etc It is not waterproof Any moisture inside the monitor could cause extensive damage VOM 78T OPERATIONS MANUAL INSTALLATION INSTRUCTIONS VOM 78T MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver e g Center of dash overhead or in dash Do not impede the operator s view of any vehicle controls or the view outside the vehicle 2 Use a compression plate to attach the monitor bracket to the dash or overhead See Fig 1 3 Adjust mounting angle of the monitor to allow driver to easily view the screen from all seat position See Fig 2 4 f necessary snap sun visor into groove on front face of monitor Press all 4 sides of the visor to snap it into place VEC 65 amp VCT 655 CABLE Not supplied 1 The camera to cable connection is waterproof The cable to monitor connection is not waterproof Be sure to orient the cable properly The cylindrical end attaches to the camera The rectangular box end attaches to the monitor See Fig 3 Do not run the VEC 65 amp VCT 655 cable over sharp edges Do not kink the cable Keep the cable away from hot and rotating parts Place all excess cable in convoluted tubing Tie the cable securely MAINTENANCE Remove dust and dirt with a damp soft cloth Heavier dirt should be removed with a damp soft cloth and mild detergent Do not use strong cleaning agents containing gasoline thinner benzene or alcohol These substances
11. may damage the exterior surface of the monitor VOM 78T 3 VOM 78T OPERATIONS MANUAL CAUTION 1 Before drilling be sure no cable or wiring is on the other side Be sure to drill a 3 4 diameter hole only 2 Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of being hooked during production 3 Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components 4 To increase protection of cable place all excess wire and extension cable in convoluted tubing 9 Do not twist camera cable and do not cut camera pigtail or cable WIRING MONITOR 1 See wiring diagram for connections to ignition ground and back up circuit See Fig 3 2 Wiring Monitor Insert extension cable into camera 1 position if 2 camera are used be sure to mark each extension cable properly and plug second cable into camera 2 position Bundle excess cable together using a cable tie or vinyl tape This will avoid possible damage to cable during operation See Fig 3 3 The red wire is connected to an ignition power source the black wire is connected to chassis ground and the blue wire is connected to the vehicle s back up circuit See Fig 3 VOM 78T OPERATIONS MANUAL FUNCTIONS AND OPERATION Front of Monitor See FIGURE 4 Power switch STD BY Monitor operates when vehicle transmission is switched into REVERSE ON monitor and system operate when ignition switch is ON CA1 CA
Download Pdf Manuals
Related Search