ASA Electronics AOM703 User's Manual
Contents
1. motor vehicle safety regulations Warnings Camera Monitor Warning 1 Camera monitor system aids in the use of but does not replace vehicle side rear view mirrors 2 Objects in camera monitor view are closer than they appear W hen backing up proceed cautiously and be prepared to stop Installation Location It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped with a television viewer or screen located at any point forward of the back of the driver s seat or in any location that is visible directly or indirectly to the driver while operating the vehicle The Voyager product is designed to be used primarily as a rear observation device in conjunction with closed circuit cameras In any installations where the Voyager is used to display television broadcasts or recorded video playback installation location must adhere to local laws and regulations Tampering To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are potentially harmful voltages inside the monitor There are no user serviceable parts inside If evidence of tampering is detected the warranty will be considered void Moisture Y our Voyager AOM 703 was designed to be water resistant While it will withstand short periods of exposure to moisture this product does contain sensitive electronic components and exposure to moisture should be limited by the user installer This product is not designed for applications where cons2. AOM703 7 FLAT PANEL COLOR OBSERVATION MONITOR OWNER S MANUAL OWE AOM703 Features 7 High Performance Color LCD Monitor Water Resistant Design Built in A udio Speaker with Volume Control and 12V Trigger 3 Camera A V Input with Source Select Control Backlit Controls and Day Night Picture M odes for Nighttime Use Auto M anual Power On Sun Visor Included Visit us at http www asaelectronics com Patent Pending Important Please Read This Manual Before Installing Congratulations on your purchase of a Voyager AOM 703 LCD Observation M onitor With proper installation and use your AOM 703 is designed to provide you with years of trouble free operation This manual contains important information required to properly install and operate the unit Please read this manual thoroughly before beginning All Voyager Observation products are strictly intended to beinstalled as asupplement aid to standard rear view mirror systems that may already exist in your vehicle Voyager observation products are not intended for use as substitutes for rear view mirror devices or for any other standard motor vehicle equipment required to be installed on vehicles by law While Voyager observation products contribute to improving the vehicle operator s field of view these products are no substitute for proper defensive driving techniques and observance of traffic laws and
3. If no buttons are pressed within 6 seconds or controls other than the Picture and Volume buttons are pressed the unit will exit the Picture A djustment mode 5 Volume Buttons This 2 button set of controls adjusts the output volume of the built in audio speaker when the audio function is enabled see typical system connection diagram The button increases output volume The button decreases output volume Volume level is indicated by the OSD bar graph at the bottom of the screen These buttons also serve as adjustment controls while inthePictureA djustment M enu mode see above section for details N ote The A OM 703 requires 412V to be applied to the Audio Enable trigger input in order to activate the built in speaker If no audio output is heard from the speaker regardless of the volume level adjustment check this connection INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLATION Before drilling be sure that no cable or wiring is on the other side Clamp all wires securely to reduce the possibility of them being damaged during installation and use K eep all cables away from hot or moving parts and electrically noisy components Wiring Definitions Power connection 1 ACC 12V Red Pin 2 Standby Reverse Trigger Blue wire Pin 3 Ground Black wire Pin 4 Audio Trigger White wire Pin5 Standby L eft Trigger Brown wire Pin6 Standby Right Trigger Green wire m inpu
4. SIN FIGURE A PLACE RANGE MARKER DECALS ON SCREEN OF MONITOR OVER IMAGE OF INDICATOR MARKERS ON GROUND BEHIND VEHICLE AS VIEWED ON THE MONITOR SCREEN THIS GIVES YOU A VISUAL REFERENCE OF ACTUAL DISTANCE BEHIND VEHICLE AS OBJECTSARE VIEWED INDICATOR MARKERS WIDTH OF VEHICLE FIGUREA JOO FIGURE B JUNCTION BOX MOUNTING TEMPLATE 5mm PANAVISE MOUNT TEMPLATE OPTIONAL ACCESSORY TROUBLESHOOTING SYMPTOM CAUSE SOLUTION No power No 12V accessory No ground mis wired reversed Replace circuit fuse monitor has protection device built in reset check ground connection verify power is being supplied Video No audio White audio trigger wire not powered Volume adjust down Connect to 12V ACC or reverse light circuit turn volume adjustment up Monitor does not Blue standby wire not powered Connect to reverse circuit 12V activate in Standby reverse trigger Negative dark Low voltage Brightness Check voltage power and ground connections video image adjustment down turn brightness adjustment up No video no audio Camera connection Check camera input selection connection to camera and junction box correct camera connection plugged incorrectly Vehicle battery drained 12V ACC red wire connected to vehicle battery Provide 12V ACC red wire power from switched circui
5. igger 3 Green wire should be connected to the trigger feed of the Vehicles Right turn signal When triggered the Right Camera image will be displayed on AV 3 Note The unit will not be turn ON when the hazard light are activated Y DB The power button features dual illumination bright and dim In installations where the unit is not wired for Stand by operation and power is applied to the unit the Power Button will dimly glow when the unit is off allowing the user to easily find the control in low light Illumination switches to full intensity when the unit is turned on 2 Source Input Select Button This control toggles the active display image back and forth between AV 1 AV 2 or AV 3 inputs 3 Day Night Mode Button This control toggles the unit between Day and Night LCD illumination modes In the Day mode the LCD backlight intensity is at maximum In Night mode the LCD backlight is dimmed to a preset level that is more suitable for low light operation 4 Picture Adjustment Menu Button This control accesses an On Screen Display OSD menu for four LCD picture adjustments Brightness Contrast Color and Tint The first depress of the button accesses the Brightness adjustment The Volume controls adjust the level which is indicated by the bar graph at the bottom of the screen Each consecutive depress of the Picture button accesses the adjustment screen for each picture adjustment
6. ng the 2 x 4 velcro strip included There are 2 options for connecting the LCD monitor to the junction box If the application is such that the monitor is in close proximity to the junction box the AOM 703 monitor can be connected directly to the junction box If the junction box is mounted further from the monitor use the 5 intermediate cable included with the A OM 703 to connect the monitor to the junction box If more cable length is needed additional 5 lengths of the intermediate cable can be purchased See the accessory list at the back of this manual for part number details Connect the 6 pin power harness to vehicle See system connection illustration page 8 Plug camera extension cable available separately into AV 1 AV 2 or AV 3 input connector on the junction box Plug observation camera into camera extension cable Make sure all cables are routed away from hot or moving parts and away from sharp edges Secure cables with wire ties 10 For rear observation applications range marker stickers have been included with this product These markers are designed to adhere to your LCD monitor and provide a reference for gauging distance See page 9 for illustration showing proper use and installation of the range markers iS T T REAR OBSERVATION INSTALLATION DISTANCE MARKER USE INSTALLATION PLACE INDICATOR MARKERS CONE BOX ANY REFERENCE OBJECT HANDY BEHIND VEHICLE A
7. t 12 PRODUCT SPECIFICATIONS LCD panel specifications Size Type 7 diagonal TFT LCD Brightness 350 nit min 420 nit typ Contrast Ratio 200 min 300 typ View Angles CR210 Response Time Top 12 o clock 0 Bottom 6 o clock 50 min Horizontal 50 min Rise 12ms typ 50ms max Fall 18ms typ 60ms max Back light Type CCFL Back light Life 30k hrs min 40k hrs typ Operation Temperature Range 20 C to 65 C Storage Temperature Range 40 C to 80 C Max Humidity 100 RH M ax Vibration Force 2 5G M ax Shock Force 100G Operating Voltage Range 11V DC to 26VDC Current Draw typical 50mA Idle 1 50A typ 1 70A max Signal System NTSC Video Aspect Ratio 16 9 Input format Composite NTSC Input level 1V p p into 750 Audio Input level 10dBV nominal 317mV Product Weight 3 0105 approximate ProductOverall Dimensions 7 197mm W x 5 Ya 134mm H x 1 3 16 29 5mm D Visit us at http www asaelectronics com 13
8. t Connection for camera or camera extension cable Camera input Connection for camera or camera extension cable m Camera C input Connection for camera or camera extension cable LCD panel 13 pin DIN cable connection junction box to monitor Procedure 1 2 Choose the monitor junction box and camera mounting locations Install all required cables in vehicle Y 19mm hole should be drilled for passing cables through vehicle walls barriers etc After the intermediate cable is passed through the hole install the split grommet included If additional cable protection is required install convoluted tubing over the cable 3 After cable wiring has been routed and components are in place temporarily make all system connections and perform a system function check If system does not operate properly see the troubleshooting section of this manual If using an optional PanaVise stalk mount available separately use the mounting template provided on page 11 Install the PanaVise mount to the LCD monitor using the 10 self drilling screws included mportant Do not use screws other than those provided with the OM 703 Void of warranty and serious product damage will occur Use the template provided on page 10 for proper placement of the junction box mounting holes Use the 8 self drilling screws included to secure the junction box in the desired location The junction box can also be mounted usi
9. tant exposure to moisture or immersion can be encountered This unit should NEVER be cleaned with a power washer or used where direct power washer spray may be encountered PACKING CONTENTS SPLIT GROMMET DISTANCE MARKER 1 O D 3 161 D STICKER QTY 1 QTY 1 4 BLACK WIRE TIE QTY 4 CONTROLS AND OPERATION 1 Power Stand By mode ThePower Stand B y button has two possible operation modes a Manual mode Turned on manually by the user by pressing the Power button b Stand B y mode Turned on by astand by trigger wire generally connected to thevehicles 12V reverse back up lights or turn signals Manual M ode wiring For manual mode operation theA OM 703 should be wired as follows ACC 12V Red wireshould be connected to the vehicles accessory feed GND Black ground wireshould beconnected to chassis ground Standby M odewiring For standby mode operation theA OM 703 should be wired as follows ACC 12V Red wireshould be connected to the vehicles accessory feed GND ground wire should be connected to chassis ground Standby CameraT rigger 1 Bluewire should be connected to the reverse feed of the vehicles back up lighting system W hen triggered the R everse Camera Image will bedisplayed on AV 1 Standby Camera Trigger 2 Brown wire should be connected to thetrigger feed of the vehicles L eftturn signal W hen triggered the Left Camera image will bedisplayed onAV 2 Standby Camera Tr
Download Pdf Manuals
Related Search