Arrow Plastic VL8662-A User's Manual
Contents
1. Z Pa lt 2 gt E lt 13 Step 1 Parts Needed For Floor Frame Assemblies 8941 Ramp 1 9379 Front Floor Frame 2 9377 Rear Floor Frame 2 The front floor frame is made up of three pieces The rear floor frame is made up of two pieces The holes in these pieces will align when the pieces are positioned with correct amount of overlap The illustrations below show the proper overall length for the front and rear Proceed as follows 1 Place the front floor frames as shown Center the ramp with drain holes facing outside ontop of the two front floor frames Join the frames by inserting eight screws 2 Overlap the rear floor frames as shown The holes in these pieces will align when the pieces are posi tioned with correct amount of over lap See the illustrations below for the proper overall length of the rear floor frame Join the frames by insert ing five bolts into frame set as shown 3 Double check the length of each and set these pieces aside for later use 14 9379 9377 FF FF Front Floor TEP S Fk 8941 ga Frame Assembly 1 95 7 8 2 43m 1 9379 CE i 9379 DRAIN HOLES FACE OUTSIDE STEP 2 Se PF F Rear Floor Frame 95 7 8 2 43m 95 7 8 2 43m Front Parts Needed For 6615 Rear Wall Angle 2 The main frame pieces reinforce the walls These pieces w2. Watch the Weather Be sure the day you select to install your building is dry and calm Do not attempt to assemble your building on a windy day Be careful on wet or muddy ground Teamwork Whenever possible two or more people should work together to assemble your building One person can position parts or panels while the other is able to handle the fasteners and the tools Tools and Materials These are some basic tools and materials you will need for the construction of your building Decide which method of anchoring and the type of foundation you wish to use in order to form a complete list of the materials you will need Required Required Eye Goggles Work Gloves e No 2 Phillips Screwdriver e Step Ladder Optional Time Savers Foundation Preparation With Hardened Magnetic Tip e Utility Knife Scissors e Wrench Nut Driver e Hammer and Nails pee A heii tear or vari e Pliers e Electric Cordless Drill e Spade or Shovel a oan eo ea fi e Carpenter s Level Square e Hand Saw Power Saw as much as 40 e Tape Measure e String for squaring frame e Lumber and or Concrete Selecting and Preparing Your Site Before assembly you will want to decide on a location for your building The best location is a level area with good drainage eAllow enough working space for ease of moving parts into position during assembly Be sure there will be enough space at entrance for doors to open fully and enough space around the building to
3. A To support a plywood deck B To be filled with sand We recommend the combined use of 1 an ARROW FLOOR FRAME KIT and 2 an ARROW ANCHORING KIT as an effective method of securing the building to the ground Allow 1 2 hours for construction OPTION 2 Wood Platform If you decide to build your own foundation be sure to select the appropriate materials These are the recommended materials for your foundation 2 x 4 s 5cm x 10cm Pressure Treated Lumber 5 8 1 5cm 4 x 8 122cm x 244cm Plywood exterior grade 10 amp 4 penny Galvanized Nails Concrete Blocks optional The platform should be level and flat free of bumps ridges etc to provide good support for the building The necessary materials may be obtained from your local lumber yard To construct the foundation follow instructions and diagram Construct frame using 10 penny galvanized nails Measure 16 24 40 6cm 61cm sections to construct inside frame see diagram Secure plywood to frame using 4 penny galvanized nails Allow 6 7 hours for construction Note Platform Slab will extend 9 16 1 4cm beyond floor frame on all four sides Seal this 9 16 of wood with a roofing cement not included or bevel this 9 16 of OPTION 3 Concrete Slab concrete when pouring for good water drainage The slab should be at least 3 to 4 8 10cm thick It must be level and flat to provide good support for the frame The following are the recommended materials
4. bottom of the right door assembly on your left when you are inside the building behind door jamb into the front frame track 2 Position the top of the door so that the holes in the door line up with the holes in the door slides 3 Fasten the door to the door slides using two 10Bx1 2 screws per door slide NOTE The holes in the door slides allow you to adjust the doors Place the door in the middle holes 4 Repeat steps 1 through 3 for the left door Gable Door Track Door Slide Door Adjustment Holes Allow 4 Doors to Meet Evenly Along Their Length Horizontal Door Brace Keep this Owner s Manual and Assembly Instructions for future reference 31 EH86 A EH86S SA8662 A LMS6 VLS662 A MLS6 A WLS6 A SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture Problem areas include screw holes unfinished edges or where scrapes and nicks occur in the protective coating through normal assembly handling and use Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing or stop it quickly as soon as it appears 1 Avoid nicking or scraping the coating surface inside and out 2 Use all the washers supplied In addition to pro tecting against weather infiltration the washers pro tect the metal from being scraped by the screws 3 Keep roof base perim
5. does not go thru wall channel a atoverlap lt eH A 5 When you have attached all wall Use bolts and atl panels in the correct positions the nuts thru wall building will look like this angle overlap at the top of panel at rear STEP 5 m Aii 4 21 Parts Needed For Door Jamb 9369 Door Jamb 2 The door jambs reinforce the door opening and provide an attractive trim Follow these steps for both door jambs 1 Fasten a door jamb to the front panel with three bolts nuts andacorn nuts as shown Push a plug into hole at center of jamb closest to door opening 2 Fasten the top of the door jamb to the door track with two screws Do the same for the bottom into frame Repeat steps 1 through 2 for the opposite door jamb INSIDE OF RS BUILDING TOP VIEW 3 bolts Door Track Acorn Nut Q 4 lt 3 Cross Section Plug Top View Hex Nut lt 9 9369 N Door Track e 7907 Left Gable 2 Gable Assemblies 7916 Roof Beam Bracket 4 Parts Needed For 7906 Right Gable 2 Step 10 The gables go on top of the front and rear walls to support the roof beams NOTE The gables are packed nested together and might be mistaken as one piece Carefully separate them before continuing 1 Attach the four roof beam brack ets to the gables using two bolts washers and
6. later step 3 Position door slides onto the legs from the end of door track assembly as shown in the end view 4 Set this piece aside for later use EN jo ra A 66769 END VIEW N Parts Needed For 6617 Door Track Splice 1 Door Track Assembly 9378 Door Track 2 94 5 8 2 40m STEP 3 94 5 8 94 5 8 NOTE Door Track Splice painted part 2 40m 8946 Side Floor Frame 2 Floor Frame Rear Floor Assembly 1 Parts Needed For Front Floor Assembly 1 Step 5 B18 1 Assemble the four corners of the floor frame using two screws at each corner as shown At the front corners fasten bolts through from the bottom with nuts on top 2 Measure the floor frame diago nally When the diagonal measure ments are equal the floor frame is When Diagonal Measurements square are Equal the Floor Frame is Square NOTE If using a wood platform or concrete slab do not fasten the floor frames to your base at this time You will anchor the building after it is erected NOTE If you have purchased a Floor Frame Kit you need to install it at this time The floor frame must be square and level or holes will not align Parts Needed For 9381 Front Corner Panel 2 Corners 9385 Rear Corner Panel 2 NOTE The remainder of the building assembly requires many hours and more than one person Do not continue beyond this point if you do not have enough t
7. storage building must be anchored to prevent wind damage A foundation is also necessary as a base in order to construct a square and level building Anchoring and foundation materials are not included with your building We recommend the combined use of an Arrow Floor Frame Kit and an Arrow Anchoring Kit as an effective method of securing your building to the ground Available by mail order or at your local dealer or you may construct a foundation and anchoring system of your choice Your assembly instructions provide information on a few methods commonly used to secure and level a storage building Parts and Parts List Check to be sure that you have all the necessary parts for your building eAll part numbers can be found on the parts All of these numbers before the must agree with the numbers on the parts list The parts list is located on page 12 elf you find that a part is missing include the model number of your building and contact Arrow Group Industries Inc Customer Service Department Route 50 East Breese Illinois 62230 1 800 851 1085 eSeparate contents of the carton by the part number while reviewing parts list The first few steps show how to join related parts to make larger sub assemblies which will be used later eFamiliarize yourself with the hardware and fasteners for easier use during construction These are packaged within the carton Note that extra fasteners have been supplied for your convenience PLAN AHEAD
8. them on your unit Immediately clean the area with a wire brush wash it and apply touch up paint per manufacturer s recommendation Roof Keep roof clear of leaves and snow with long handled soft bristled broom Heavy amounts of snow on roof can damage building making it unsafe to enter In snow country Roof Strengthening Kits are available for most Arrow Buildings for added protection against heavy snow accumulation Doors Always keep the door tracks clear of dirt and other debris that prevent them from sliding easily Lubricate door track annually with furniture polish or silicone spray Keep doors closed and locked to prevent wind damage Fasteners Use all washers supplied to protect against weather infiltration and to protect the metal from being scratched by screws Regularly check your building for loose screws bolts nuts etc and retighten them as necessary Moisture A plastic sheet vapor barrier placed under the entire floor area with good ventilation will reduce condensation Other Tips e Wash off inked part numbers on coated panels with soap and water e Silicone caulking may be used for watertight seals throughout the building Do not store swimming pool chemicals in your building Combustibles and corrosives must be stored in air tight approved containers Keep this Owner s Manual and Assembly Instructions for future reference ACCESSORIES ROOF STRENGTHENING heavy snow load KITS Extra roof b
9. FRON T 7875 Roof Panel 3 Install 4 roof panels in the se quence and positions shown on pre vious page Do not fasten the lower end of the panels to the side wall angles at this time Continue weather stripping the ridge opening Fasten Screws To Roof Beam roof panel overlaps not used for ridge ae cap roof center Cover the head of Fasten At Fasten At 3 bolt with the 2 5cm piece of weather PN IA stripping tape Screws To Roof Beam Do not fasten NOTE at this time Strips Narrow roof panel crimped rib is overlapped by wide rib of adjacent panel where possible NOTE If roof beam holes do not line up with the roof panel holes shift the building from left to right If this does not help your building may not be level Shim the Cut corners until holes line up ee Step 15 Parts Needed For Ridge Cap 8461 Ridge Cap 1 1 Install the ridge cap on the com pleted roof section using bolts and nuts Do not fasten the ends of the ridge cap at this time 2 Fasten the lower end of the panels to the side wall angles using screws and washers 28 Parts Needed For Step 1 6 Roof Trim 8482 Side Roof Trim 2 1 Attach the side roof trim to the lower end of the roof panels on each side of the building using screws at each panel overlap 2 Using your thumb and index fin ger overbend the bottom flange of the side roof trim and roof panel rib at the corne
10. Fasten the rear wall channel as sembly across the middle of the rear wall using screws 3 Fasten the side wall angles across the inside top of the side panels us ing screws Side wall angles must overlap rear wall angle in corners 4 Fasten the side wall channels across the middle of the side panels using screws Fasten overlaps in rear corners with screws Long Leg on Top Opening Facing in Short Leg gd on Bottom 5 Fasten the door track assembly holes on top across the top of the front wall panels using screws See the figure 20 Parts Needed For 6515 Wall Panel 4 Wall Panels 6243 Wall Panel 2 The wall panels come in two widths STEP Each wall panel has a crimped rib on one side The crimped rib should go under the rib of the panel that follows it 1 Locate all of the wall panels and set each one alongside the building ATW inter v 2 Be sure that you have the correct panels in each position Do this by overlapping the panels and deter mining if the holes line up with the holes in the frame md Panels rest on frame as shown Crimped Rib Underneath Detail Showing Center of Panel Screwed to Wall Channel 3 Fasten the wall panels at the top and bottom with screws 4 Fasten the center of each panel to the wall channel with screws Fasten overlapping ribs using a bolt and nut with two screws Ss bg sl Bolt and nut STEP k
11. Owner s Manual amp Assembly Instructions PO1 Model No EH86 A EH86S LM86 MLS6 Al SAS662 A l VLS662 A WLS86 AL World s Leading Maker of Storage Buildings CAUTION SOME PARTS HAVE SHARP EDGES CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP FOR SAFETY SAKE PLEASE READ 709141207 SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION WEAR GLOVES BUILDING DIMENSIONS Size rounded off to the nearest foot WHEN HANDLING METAL PARTS Exterior Dimensions Interior Dimensions Door Approx Foundation Storage Area Roof Edge to Roof Edge Wall to Wall Opening Size Size Sq Ft Cu Ft Width Depth Height Width Depth Height Width Height 8x6 97 1 2 x 68 3 4 43 237 99 3 4 71 1 4 697 8 943 4 66 685 8 43 1 2 60 2 4m x 1 7m 248cm x 175cm 4 0m 6 7m 253cm 181cm 177cm 241cm 168cm 174cm 110cm 152cm BEFORE YOU BEGIN Owner s Manual Before beginning construction check local building codes regarding footings location and other requirements Study and understand this owner s manual Important information and helpful tips will make your construction easier and more enjoyable Assembly Instructions Instructions are supplied in this manual and contain all appropriate information for your building model Review all instructions before you begin and during assembly follow the step sequence carefully for correct results Foundation and Anchoring Your
12. be able to fasten the panel screws from the outside Before you begin the first steps in assembling your parts a foundation should be constructed and an anchoring system should be ready to use SAFETY FIRST Safety precautions are important to follow throughout the construction of your building Care must be taken when handling various ePractice caution with the tools being used in the pieces of your building since some contain assembly of this building Be familiar with the sharp edges Please wear work gloves eye operation of all power tools protection and long sleeves when assembling or performing any maintenance on your build ing eKeep children and pets away from worksite to Do not attempt to assemble the building if parts avoid distractions and any accidents which are missing because any building left partially may occur assembled may be seriously damaged by light winds Call 1 800 851 1085 eNever concentrate your total weight on the Do not attempt to assemble the building on a roof of the building When using a step ladder windy day because the large panels acting as a make sure that it is fully open and on even sail can be whipped about by the wind making ground before climbing on it construction difficult and unsafe TO lt A LF CARE amp MAINTENANCE Finish For long lasting finish periodically clean and wax the exterior surface Touch up scratches as soon as you notice
13. d concrete slab or footing or patio blocks Contains Corner gussets perimeter clips hardware Use 1 4 x 2 Lag Screws 1 4 masonary drill bit and installation instruction 2 For Anchor Post of Concrete poured after building is erected Use 1 4 x 6 Lag Screws 65103 8 32 Hex Nut 104 66045 Handle 2 66769 Door Slide 4 6228 Track Support 2 Hardware Remove from bag of screws and save for the last step T 65900A 10Bx1 2 Black Screw 8 65923 Packed with Screws 8 32x3 8 Bolt 104 66646 65109 Washer 275 8 32 Acorn Nut 6 8 sheets of 40 Packed with Screws Sf 66183 66382 Roof Trim Cap Lower Door Guide 4 2 right amp 2 left 66029 67293 Plug 2 Weather Stripping 1 Packed with Screws 65004 8Ax5 16 Screw 266 St 67468 Peak Cap 2 Arrow Logo OOOO 7916 Roof Beam Bracket 4 11 Parts List Assembly Part Part Quantity Check Key No Number Description in carton List Rear Wall Angle Door Track Splice Horizontal Door Brace Gable Brace Roof Panel Right Gable Left Gable Ridge Cap Right Roof Panel Left Roof Panel Roof Beam Side Wall Angle Side Wall Channel Side Roof Trim Ramp Side Floor Frame Wall Panel Vertical Door Brace Right Door Left Door Wall Panel Door Jamb Rear Wall Channel Rear Floor Frame Door Track Front Floor Frame Front Corner Panel Rear Corner Panel OONDOAABRWND j IO ID DD
14. e adjustments to make sure the building is square and level This will make the roof panels fit better and holes will align Don t anchor the floor frame NOTE If a Roof Beef Up Kit was purchased assemble prior to attaching the roof panels 1 Locate the roof panels by their numbers Note the sequence and position they are to be installed 2 Position the right roof panel at the back right corner and fasten to the gable with 5 bolts and nuts and roof beams using 2 screws Do not fasten the lower end of the panel to the side wall angle at this time Hint Attach fasteners in order shown in diagram 26 Right Roof Panel 8467 2 1_ 8466 k k k 8466 4 3 8467 FRONT 8466 Right Roof Panel Nut p Washer Parts Needed For 8467 Left Roof Panel 2 Step 1 4 7875 Roof Panel 4 Roof Assembly 8466 Right Roof Panel 1 B27 8467 Left Roof Panel a 1 Weather Stripping 2 1 Install a left roof panel at the left _ Tape Roll rear and right front corner of the roof 8466 Right F Install a right roof panel at the left Roof Pane front corner of the roof 2 Cut 2 short 2 5cm strips off the roll of weather stripping tape and put them aside Cover the joint at the peak with weather stripping tape Unroll the tape and press it down over the opening at the ridge as you install each roof panel Do not cut the tape at this time Lt IP l
15. eams and gable braces designed for added protection against heavy snow accumulation Increases the strength of your roof by 50 ANCHOR KITS Model No AK4 Anchor Kit contains heavy duty steel augers 60 18m of steel cable and 4 cable clamps No digging or concrete Gea ARROW pouring just insert cable under roof rR over roof beams into augers and twist augers into the ground For buildings larger than 10 x9 use 2 kits Model No AK100 New concrete anchor system permits anchoring any size Arrow building directly to a concrete slab Each kit contains heavy duty hot dipped galvanized steel corner gussets and perimeter clips which fit over the floor frame and lag bolt into a concrete slab Full assembly instructions and a 1 4 masonary drill bit are included Model No AK600 Earth Anchor Kit anchors any size Arrow building to the ground Each kit contains heavy duty AE hot dipped galvanized steel ure corner gussets and 4 earth anchors TOOL HANGING RACK Model No TH100 The perfect tool organizer Twin 25 1 2 65cm steel channels plus five heavy duty snap in 6 ae aoe ae hangers and a small tool holder for screwdrivers pliers etc Holders slide along channel for fully adjustable spacing Great for garage basement or the back of any door Fits all Arrow storage buildings FLOOR FRAME KITS MODELS FB47410 FB5465 FB106 A FB109 A and FB1014 A Asimple new floor frame s
16. eter and door tracks free of debris and leaves which may accumulate and retain moisture These can do double damage since they give off acid as they decay 4 Touch up scrapes or nicks and any area of visible rust as soon as possible Make sure the surface is free of moisture oils dirt or grime and then apply an even film of high quality touch up paint 709141207
17. for your foundation 1 x 4 s 2 5cm x 10cm will be removed once the concrete cures Concrete Sheet of 6 mil plastic We recommend for a proper strength concrete to use a mix of 1 part cement 3 parts pea sized gravel 2 1 2 parts clean sand Prepare the Site Construct a Foundation 1 Dig a square 6 15cm deep into the ground remove grass 2 Fill up to 4 10cm in the square with gravel and tamp firm 3 Cover gravel with a sheet of 6 mil plastic 4 Construct a wood frame using four planks of 1x4 2 5cm x 10cm lumber 5 Pour in concrete to fill in the hole and the frame giving a total of 4 8 10cm thick concrete Be sure surface is level Note Finished Slab dimensions with lumber removed Allow 3 5 hours for construction and a week for concrete curing time Anchoring Anchoring Down The Building It is important that the entire floor frame be anchored after the building is erected Below are recommended ways of anchoring Arrow Anchoring Kit Model No AK4 or 60298 Anchoring into Wood Post Recommended for use with any suggested base Use 1 4 Wood Screws There are 1 4 0 63cm dia Contains 4 Anchors with Cable Clamps and holes provided in the frames for proper anchoring installation instruction Bs pA f f o OVER THE BEAMS AND INTO THE GROUND Arrow Anchoring Kit Model No AK100 or 68383 Anchoring into Concrete Recommended for use with the concrete foundation 1 For poure
18. ill later be in stalled in the center and at the top edge of the rear wall Proceed as follows Rear Wall Channel D 94 5 8 2 40m i 9924 1 Overlap the rear wall channel pieces as shown in the figure and fasten the two pieces together with one bolt in the center hole three holes will align Rear Wall Angle 2 Overlapthe rear wall angle pieces 94 5 8 2 40m as shown in the figure and fasten them together with one bolt in the center hole Rear Wall Channel 94 5 8 2 40m 3 Setthe assemblies aside You will use them later Rear Wall Angle 94 5 8 2 40m m U 15 Step 3 Parts Needed For Roof Beam Assembly 8474 Roof Beam 1 8476 Side Wall Angle 1 The roof beams join the two gables and supportthe roof panels The main roof beam is made up of two pieces fastened together 1 Place the side wall angle back to back with a roof beam and fasten together using ten screws 2 Set this piece aside for later use Assembled 8476 Side Wall Angle Main Roof Beam The door track assembly supports the sliding doors and reinforces the frontwall Itis made up of three pieces 1 Using the door track splice painted join the door track galvanized pieces end to end as shown 2 Insert four screws from the under side only Hint The holes in the top side of the door track assembly are for fastening the gable to the top of the front wall in a
19. ime to com plete the assembly today A partially assembled building can be severely damaged by light winds Each screw and bolt in the wall re quires a washer 1 Position the rear corner panels at the rear corners as shown The wid est part of each rear corner panel must be placed along the rear of the building Attach the corner panels to the floor frame with four screws 2 Position a front corner panel at the corner ofthe floor frame as shown The widest part of each front corner panel must be placed along the front of the building A small gap will exist between front corner paneland ramp Fasten the corner panel to the floor frame with three screws NOTE Be careful to install the correct panel in each position as shown 3 Double check the part numbers of the wall panels before proceeding The floor frame must be square and level or holes will not align Narrow Side STEP 1 9385 TOP VIEW Panels rest on frame as shown Washer Door Track Assembly 1 Rear Wall Angle Assembly 1 Step 7 eran ARS TO 8476 Side Wall Angle 2 Rear Wall Channel Assembly 1 9920 Side Wall Channel 2 The main frame pieces give rigidity to the side walls and provide a surface for attaching the gables which sup ene oe 2 portthe roof Inside P Building L 2 1 Fasten the rear wall angle as sembly across the inside top of the rear wall using screws 2
20. nuts NOTE Mounting leg of bracket must face toward center of gable 7916 Roof Beam Brackets 23 Parts Needed For Left Gable Assembly 2 Right Gable Assembly 2 Step 1 1 Gables Braces 6658 Gable Brace 2 1 Lift and fasten a right and left gable under angle at corner to the rear wall angle with screws Hint On the rear gable use a bolt and nut at the overlapping rear wall angle On the front gable leave out 2 screws Closest to center gable leg 2 Join the left and right gables together with a gable brace using bolts and nuts in the bottom two holes only 3 Repeat Steps 1 amp 2 for the door track on the front of building except for the track supports fasten as shown 6658 Gable Brace Din exe Track Supports 6228 24 Parts Needed For Roof Beams 1 Fasten the main roof beam to the gable brace of the front gable 2 Fasten the other end of the main roof beam to the gable brace of the rear gable 3 Fasten the remaining roof beams small holes on top as shown using bolts and nuts Main Roof Beam 1 8474 Roof Beam 2 Main Roof Beam Assembly 25 Parts Needed For 8466 Right Roof Panel 1 Installing the roof panels is best done with a step ladder Begin installing roof panels at the back right corner of the building Each screw and bolt in the roof requires a washer NOTE Measure the building diagonally again and mak
21. r inward enough so the right and left roof trim caps fit onto right and left corners 3 Fasten the roof trim caps to the side trim using a screw 4 Fasten the roof panel ribs peak caps and ridge cap together using bolts and nuts os it Side Roof Trim T Peak Cap LIA Flange lt Inward to Fit Inside of Roof Trim Cap 29 Parts Needed For 10478 Right and Left Doors 2 10498 Horizontal Door Brace 4 Door Assembly 6278 Vertical Door Brace 2 The steps on this page tell how to assemble the right door You will perform exactly the same procedures for the left door Each bolt and screw in the door requires a washer Proceed as follows 10498 1 Attach the handle to the door with 2 bolts and nuts as shown 10478 Right Door 10478 Left Door STEP 1 2 Hold the vertical door brace against the center of the inside sur face of the door and turn the screw to hold the vertical door brace in place Fasten to door above and below center connection using 2 screws 3 Put a horizontal door brace onto the top edge and bottom edge and fasten with 7 bolt in the center 4 Attach the lower door guides and END VIEW bolts as shown SHOWING 5 Repeat steps 1 through 4 for the left door Parts Needed For Right Door Assembly 1 Door Installation amp Adjustment Left Door Assembly 1 1 From inside the building put the
22. ystem made of heavy duty hot dipped galvanized steel Use as foundation for plywood sand or stone ATTIC KIT WORKBENCH KIT Heavy duty galvanized steel bars that fit all 10 wide Arrow buildings They install quickly and easily to help organize space and create more useable space as an attic or workbench Will hold up to 250 Ibs 113kg evenly distributed Model No Fits AT101 Shipping Weight 10 Long 250 Ib 113kg load Fits all Arrow 10 wide buildings 16 Ibs 7kg Must be drilled for use as workbench in Estator Even weight distribution SHELF UNITS Heavy duty galvanized steel shelf units help organize storage space They easily mount on the wall or sit on the floor Fits all Arrow buildings SS Fi Model No S8404 e Makes 8 to 12 20 30cm wide shelves in any length e Brackets braces hardware included Lumber is not included Model No SS900 A e Grey color e 3 shelves e Holds up to 85 Ibs 38kg even weight distribution Some drilling required to fit buildings without mid wall bracing PO THIS PAGE WAS LEFT BLANK INTENTIONALLY PO THIS PAGE WAS LEFT BLANK INTENTIONALLY Foundation The Foundation For Your Building OPTION 1 ARROW FLOOR FRAME KIT order No FB106 A or 68381 A Arrow has the best base for your building in this simple kit It keeps stored items above the ground This kit should be used with one of the following
Download Pdf Manuals
Related Search