Ariens C-2014R User's Manual
Contents
1. WARNING AVOID INJURY Auger must stop within 5 seconds when attachment lever Ah is released or serious injury or unit damage may result Page 3 of 8 Date February 26 2014 No C 2014R Replaces C 2014 6 Replace chute crank and secure with spring clip pin If Equipped Reconnect remote deflector cable to control lever 7 Replace gear cover on top of chute pedestal 8 Run in the attachment belt see Run in Attachment Belt on page 4 9 Replace belt cover and tighten hardware 2 4 5 N WAS it A IPBA UP gt S 1 Traction Belt Idler 1 Sf 2 Traction Drive Belt 4 3 Engine Sheave AL y 4 Belt Finger A 5 Attachment Drive Belt 8 E 6 Attachment Pulley 6 7 Attachment Idler Nut 8 Attachment Belt Idler Figure 2 pe 1 8 3 2 mm Maximum i EA 1 Belt Finger S 2 Attachment Drive Belt 3 Swing Gate Pivot Bushing Figure 3 RUN IN ATTACHMENT BELT 1 Start unit in a well ventilated area 2 Engage attachment clutch lever and run attachment for about 15 minutes 3 Stop unit wait for all moving parts to stop and remove spark plug wire 4 Adjust clutch idler see Attachment Clutch Brake Adjustment on page 5 Page 4 of 8 Date February 26 2014 No C 2014R Replaces C 2014 ATTACHMENT CLUTCH BRAKE ADJUSTMENT WARNING IMPROPER ADJUSTMENT could result in unexpected movement of auger and impeller causing death or serious injury AUGER IMPELLER MUST STOP within 5 sec2. Cable Attaching Hardware 3 Remote Trigger Cable 4 Bottom Cover 5 Assembly Bolt Holes Replace Attachment Drive Belt Figures 8 and 9 1 Place new belt onto lower pulley and while holding brake out of way tip unit together 2 Secure brush to frame with cap screws 3 Place belt onto engine sheave 4 Replace belt finger Page 7 of 8 Date February 26 2014 No C 2014R Replaces C 2014 IMPORTANT With the clutch lever engaged the belt finger located opposite the belt idler must be less than 1 8 in 3 2 mm from the belt but not touching the belt or belt grabbing may occur causing brush to rotate while the attachment clutch is disengaged Figure 9 5 Adjust clutch see Attachment Clutch Brake Adjustment on page 5 Replace belt cover and secure with cap screws Replace bottom cover and secure with cap screws Reinstall remote trigger cable to brush assembly Run in the attachment belt see Run in Attachment Belt on page 4 Replace the belt cover O O ON OD 2 4 A 7 M 4 IBN Wf a 1 A J D S EX Py S 5 1 Traction Belt Idler y X 3 Engine Sheave 4 Belt Finger 5 Attachment Drive Belt 6 Attachment Pulley 7 Attachment Idler Nut 8 Attachment Belt Idler ON vy yy 2 Traction Drive Belt ZA I Figure 8 1 8 in 3 18 mm Maximum 1 Belt Finger 2 Belt Figure 9
3. 11 Draw a check mark on the model serial number label with an indelible black marking pen to signify that the repair has been completed See Figure 6 Page 8 of 8
4. 45598 145699 146057 920403 Sno Tek 28E 126501 127141 127143 127145 127185 127197 127237 127241 127291 127293 127326 127328 127338 127340 127341 921025 Ariens PB 28 All Season 40600 40660 Brush 921026 Gravely PB 28 All 40061 40079 Season Brush 921313 Ariens 28 Brush CE 40163 40174 939401 Sno Tek 20E 90112 90140 90619 90621 90623 ATTACHMENT DRIVE BELT PULLEY REPLACEMENT SNO THRO amp SNO TEK MODELS Models 920013 920014 920021 920022 920402 920403 939401 Remove Attachment Drive Belt Figures 1 2 and 3 1 Shut off engine remove key disconnect spark plug wire and allow unit to cool completely 2 Loosen the hardware securing belt cover to unit NOTE DO NOT completely remove the hardware from unit ON DOO W Remove belt cover Remove gear cover from top of chute pedestal Remove spring clip pin from chute crank and separate Remove remote deflector control cable from control lever if equipped Remove belt finger by removing cap screws mounting belt finger to engine Figure 2 Remove attachment drive belt from engine sheave it may be necessary to turn engine sheave using recoil starter handle Page 2 of 8 Date February 26 2014 No C 2014R Replaces C 2014 CAUTION Always support Sno Thro frame and housing when loosening the cap screws A holding them together Never loosen cap screws while unit is in service p
5. Date February 26 2014 No C 2014R Replaces C 2014 Service Campaign THE KING OF SNOW Ariens Company 655 W Ryan St Brillion WI 54110 www ariens com Product Family Ariens Compact Sno Thro Ariens Compact Track Sno Thro Sno Tek Ariens PB 28 Gravely PB 28 Subject Important Product Safety Recall Dealer Action STOP SALE Repair Immediately Ariens Company has identified a potential safety concern on models and serials listed in the table below The auger drive pulley 00268951 may develop a crack which could affect the brake s ability to stop the auger impeller resulting in an unsafe condition Dealers are instructed to Stop Sale Immediately of any unsold inventory which falls into the model and serial ranges listed Additionally dealers are asked to contact consumers who purchased affected machines from your dealership to coordinate repair of those machines as soon as possible Ariens Company is sending a letter to registered owners of all affected machines alerting them to this situation Ariens Company has been reworking product since this issue was identified and all machines which have been reworked by Ariens Company will have a black check mark on the carton label as well as the model serial label on the machine Dealers are asked to order kit 52001800 and install it on each affected unit The kit consists of a replacement pulley and hub assembly Dealers should file a warranty claim for each pulley replacemen
6. abel Figure 6 Page 6 of 8 Date February 26 2014 No C 2014R Replaces C 2014 ATTACHMENT DRIVE BELT PULLEY REPLACEMENT POWER BRUSHES Models 921025 921026 921313 Remove Attachment Drive Belt Figures 7 and 8 1 Shut off engine disconnect spark plug wire and allow unit to cool completely Remove the hardware attaching the remote trigger cable to the brush assembly Remove two screws securing belt cover to unit and remove belt cover Remove belt finger by removing cap screws mounting belt finger to engine Figure 8 Remove attachment drive belt from engine sheave it may be necessary to turn engine sheave using recoil starter handle oar WO P WARNING Always support Sno Brush frame and brush assembly when A loosening the cap screws holding them together IMPORTANT To avoid bending bottom cover when tipping unit apart support handlebars firmly and remove bottom cover by removing six cap screws before separating unit 6 Support frame and brush assembly 7 Remove cap screws holding brush assembly to frame two on each side 8 Separate assembly from unit Lower handlebar on floor 9 Remove attachment drive belt from lower pulley hold brake away from belt 10 Remove attachment pulley and discard DO NOT reuse pulley 11 Replace attachment pulley with kit 52001 800 Torque to 120 Ibs in 1 Brush Assembly 2
7. onds when Attachment Clutch Lever is released AVOID INJURY Read and understand the entire Safety section before proceeding WARNING Adjustment procedure requires the engine to be run with the belt cover off Remove Attachment Cable Slack Figures 4 and 5 1 Shut off engine remove key disconnect spark plug wire and allow unit to cool completely Loosen hardware securing belt cover to unit DO NOT completely remove the hardware from unit Remove belt cover Loosen jam nut on cable adjustment barrel and then turn the adjustment barrel down to shorten cable and remove all cable slack Figure 4 oar WwW P 1 Attachment Clutch Cable 2 Cable Adjustment Barrel 3 Jam Nut Figure 4 6 With the attachment clutch disengaged check that the attachment idler arm lightly touches the frame Figure 5 7 Tighten jam nut on cable adjustment barrel Page 5 of 8 Date February 26 2014 No C 2014R Replaces C 2014 With the attachment clutch disengaged check the attachment idler arm position here The attachment idler arm should lightly touch the frame Figure 5 8 Draw a check mark on the model serial number label with an indelible black marking pen to signify that the repair has been completed Figure 6 Draw check mark on model serial number l
8. osition IMPORTANT To avoid bending bottom cover when tipping unit apart support handlebars firmly or tip unit up on housing and remove bottom cover by removing six cap screws before separating unit 9 Support Sno Thro frame and housing 10 Remove hex bolts securing housing to frame two on each side Tip housing and frame apart on pivot pin 11 Separate housing from unit 12 Remove attachment drive belt from attachment pulley 13 Remove attachment pulley and discard DO NOT reuse pulley 14 Replace attachment pulley with kit 52001800 Torque to 120 Ibs in 1 Pinion Gear 2 Belt Cover 3 Spring Clip Pin 4 Chute Crank 5 Gear Cover 6 Chute Pedestal Figure 1 Replace Attachment Drive Belt 1 Place new belt onto attachment pulley Figure 2 NOTE Engage attachment clutch lever while connecting housing to frame to hold brake out of the way 2 Tip housing and frame back together and secure with hex bolts 3 Place belt onto engine sheave 4 Replace belt finger IMPORTANT With the attachment clutch lever engaged the belt finger located opposite the belt idler must be less than 1 8 3 2 mm from the belt but not touching the belt or belt grabbing may occur causing impeller to rotate while the attachment clutch is disengaged Figure 3 5 Adjust clutch see Attachment Clutch Brake Adjustment on page 5
9. t using a flat rate code of 20999 Please make sure that the machine is within the model serial numbers listed below Warranty claims will be reimbursed for 0 50 at the dealer s standard shop labor rate Please direct any questions to Ariens Technical Service at 888 927 4367 Page 1 of 8 Date February 26 2014 No C 2014R Replaces C 2014 Model Description Serial Number Range 920013 Ariens ST22LE Compact 124912 124935 124937 125008 125037 125060 Sno Thro 125094 125271 920014 Ariens ST24LE Compact 142966 142999 143264 143272 143274 143281 Sno Thro 143284 143287 143289 143291 143304 143306 143309 143313 143432 143434 143435 143439 143445 143448 143450 143462 143466 143467 143469 143496 143500 143502 143506 143511 143513 143518 143520 143535 143700 143728 920021 Ariens ST22LE Compact 3089 3100 3510 3940 3942 4360 4363 4365 4372 Sno Thro 4374 4377 4382 4384 4386 4389 4398 4400 4404 4405 4409 4411 4415 4418 4593 4595 4617 4619 4621 4623 5815 5817 5819 5847 5849 5883 5885 5886 5893 5895 5899 6000 6151 6153 6172 920022 Ariens ST24LET 531 576 701 712 Compact Track Sno Thro 920402 Sno Tek 24E 143967 145036 145062 145095 145097 145500 145591 145593 145594 145596 1
Download Pdf Manuals
Related Search