Arboria Heritage Arbor User's Manual
Contents
1. ground Insert wing panel to ensure a good fit adjust as needed before p concrete has fully set Xs 445 35 100 3 of 4 9 29 2006 Division of LWO Corp P O Box 17125 3841 North Columbia Boulevard Portland Oregon 503 286 5372 fax 503 286 4092 STEP 6 CONNECTING WING TO ARBOR PANELS AND POSTS SLEEVE Align the lattice of wing panel to the lattice of the arbor s side panel Install the wing panel panel using 2 1 2 washer head screws You will need two on the top and two on the bottom through the frame of the wing panel These self tapping screws will help prevent splitting wood STEP 7 SHIMMING AND TRIMMING POST SLEEVE e Useshims adhesive and finish nails or screws to secure theshims and sleeve firmly to the 4x4 post Besureto shim both the top and bottom of the post e Trim shims flush with the sleeve surface e Trim base molding to fit the post sleeve e Using wood adhesive and galvanized finishing nails connect all four sides of the base molding to the post sleeve e Finish the installation by capping the post sleeve with the post caps use wood adhesive or finish nails to secure the post cap to the post sleeve Congratulations You ve done it 445 35 100 4 of 4 9 29 2006 Division2. header Install two of the included braces using 2 1 2 A and x Screw s Turn arbor 180 degrees by lifting the arbor up 7 right and back to the ground so that the second x header is under the posts Repeat steps one and two attaching the header and braces STEP 3 INSTALLING THE CAPS Securely prop the header end of the arbor 7 off the ground U se a 3 12 screw to install thefirst cap into the marked center point on top of the header U se the 9 7 8 spacer block and 3 1 2 screws to install the remaining caps 445 35 100 2of4 9 29 2006 Division of LWO Corp P O Box 17125 3841 North Columbia Boulevard Portland Oregon 503 286 5372 fax 503 286 4092 STEP 4 INSTALLING ARBOR IN PROPER LOCATION The most common method of installation is to secure the arbor to concrete footings using the four anchors provided It may also be Diagram 1 possible to secure the arbor to an existing structure such as a Pj fence post if you would likeit installed on concrete or decking If choosing this option see your local hardw are dealer for the appli cable hardw are Anchor butts into bottom of rail Anchor and Concrete Installation A Movethe arbor to its final location this will require some Side panel assistance W hen you are satisfied with the location mark the position of the posts move the arbor aside and lay it c
3. of LWO Corp P O Box 17125 3841 North Columbia Boulevard Portland Oregon 503 286 5372 fax 503 286 4092
4. arefully on its side Dig a hole at least 6 wide and 12 deep for each post p B Attach the anchors to the posts using the 3 4 screws pro Pa _ Post vided See Diagram 1 Post a C Carefully move the arbor back to its final position support it plumb and level over the holes with bricks stones or blocks Anchors eos eae Soil of wood under the side panel rails The post bottoms should URE ee ET o be close to the level of the ground surface See Diagram 2 eae ea een i D Fill each hole with bagged concrete mixed according to the l ae manufacture s instructions Concrete should come to within Diagram 2 14 of the bottom of the post but the post should not bein concrete STEP 5 SETTING THE POSTS POST SLEEVES FOR GRAND ENTRY The following steps only apply if you have purchased the complete H eritage Grand Entry package Temporary supports Concrete Now that the arbor is in place measure 33 out from the side a panel post to locate the center position of the 4x4 post Align the center of arbor post with the center of the 4x4 post N Arbor Side P Post Dig a hole 24 deep and 10 wide install a5 4x4 pressure treated post using concrete The posts should be plumbed in two direc Wing tions Post sleeve Slide the post sleeve over the post with the notched sides facing the ground Use shims to elevate the post sleeves 1 4 off the
5. he ee ASSEMBLY INSTRUCTIONS ORK Heritage Arbor Grand Entry PLEASE READ THROUGH BEFORE STARTING ASSEMBLY COMPONENTS LIST Complete Assembly Headers 2 Components 5 8 Arbor side panels 2 reer Sd ony O Caps 7 W ings 2 Post sleeves 2 T NNT Post Base Kit 2 O An A Post caps 2 0006006 i Hardwareincluded YOU WILL NEED HARDWARE PROVIDED Tools and Supplies Additional Tools and Arbor only Additional H ardw are e Phillips screwdriver e 5 Pressure treated 4x4 e 312 screws 22 24 2 washer head screws 8 e Tapemeasure posts 2 e 97 8 spacer block 2 square head driver bit e Carpenter Square e 2 Galvanizedtrimhead e Anchor stakekit e Premix concrete 120Ib nails _ O 3 4 screws 8 optional e Concretemixing tools O Anchors 4 e Wood shims e Wood adhesive e Premix concrete 120Ib PRELIMINARIES IF YOU PLAN TO PAINT If you wish to stain or paint your arbor entry we recommend that you do so before assembly this will make the product easier to install Be careful not to cover up guide marks on the rafters W ORK AREA Select an area close to whe
6. re the arbor entry will be installed The assembly area should be relatively flat and open with at least 8 x6 of space W e recommend the use of the shipping box as your work surface to protect the arbor entry against damage during assembly 445 35 100 1 of 4 9 29 2006 Division of LWO Corp P O Box 17125 3841 North Columbia Boulevard Portland Oregon 503 286 5372 fax 503 286 4092 STEP 1 ATTACHING THE SIDE PANELS TO THE HEADERS Headers are designed to allow three sizes of opening allowing you to choose the size of opening that best fits your project needs 5i f o ide Panel Post Outside holes for a 60 1 2 opening center holes are for 54 1 2 inside holes are for 48 12 The diagram at right shows a 54 1 2 setting Drive the 3 1 2 screw through the top holein the side panel post the screw should stick through about 1 2 Place the screw point with the appropriate hole in the header and drive the screw in the rest of theway Donot drivethe second lower screw these will be installed in Step 2 This hole is to the inside Header Repeat the above process with the second side panel on the other end of the same header STEP 2 SQUARING THE ARBOR The arbor may be squared by using a carpenter square W hen the arbor is square drive the second betw een the header and side panel or with the aid of a screws into the posts securing them to the measuring tapeand careful adjustments
Download Pdf Manuals
Related Search