Apple Dual-Slot Riser Card User's Manual
Contents
1. is not in use unplug all external cables except the power cord 6 Touch the servers metal case to discharge any static electricity Important Always ground yourself by touching the server s case before you touch any parts or install any components inside the server To avoid static electricity building back up in your body do not walk around the room until you have completed your work and closed the computer 7 Unplug the power cord Warning The power supply in the server is a high voltage component and should not be opened for any reason even when the server is off 8 Release the two thumbscrews at the front of the server Figure 1 Note The thumbscrews are captive and do not separate from the bottom housing Figure 1 Xserve Dual Slot Riser Card 2 9 Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers Figure 2 10 While depressing both levers pull the bottom housing all the way forward and remove it from the rack Figure 2 11 Place the bottom housing on a sturdy flat surface and ESD mat 12 Put on the ESD wrist strap Xserve Dual Slot Riser Card 3 Removing the Dual Slot Riser Card 1 Release the thumb screw that secures the riser s cards to the server Figure 3 2 If there are latches on either side of the riser lift them slightly to release the riser from the logic board 3 Pull the riser a short distance to the side to disconn2. Xserve Dual Slot Riser Card Replacement Instructions Follow the instructions in this sheet carefully Failure to follow these instructions could damage your equipment and void its warranty Note Online instructions covering customer installable parts are available at http www info apple com installparts Tools Required No tools are required for this procedure You may however find a Phillips screwdriver useful in releasing the thumbscrews at the front of the server Opening the Server The server slides open from the front of the rack The top cover remains in place in the rack while the bottom housing containing all internal components should be placed on a sturdy flat surface 1 Alert users that the server will be unavailable for a period of time 2 Shut down the server Warning To avoid damaging internal components or causing injury always shut down the server before opening it After you shut down the server internal components can be very hot Let the server cool down before continuing 3 Write down the server s serial number which is located on the back panel If it is necessary to set up the server s software after you replace a dual slot riser card you will be asked for the serial number at login 073 0688 Rev B 4 Ifthe server is in the locked position the yellow security LED on the front panel is on use the Allen key that came with the server to unlock it 5 Ifthe cable management arm
3. ect it and then tilt the riser and attached cards up so that the card ports clear the enclosure Remove the riser and cards from the server Figure 3 4 Disconnect the PCI card s from the riser Figure 4 Figure 4 Xserve Dual Slot Riser Card 4 Installing the Replacement Dual Slot Riser Card 1 Install the PCI card s in the replacement riser card 2 Reconnect the riser card to the logic board 3 Tighten the thumbscrew that secures the PCI card fence to the back of the server Closing the Server 1 Carefully slide the bottom housing back into the rack 2 Tighten the front thumbscrews to secure it Warning Never turn on the server unless all of its internal and external parts are in place and it is closed Operating the server when it is open or missing parts can damage it or cause injury Apple Computer Inc 2003 Apple Computer Inc All rights reserved This document is protected under U S Copyright Law and International Treaties and no part of this document may be reproduced in any form without written permission from Apple Apple is not responsible for typographical printing or inadvertent errors Apple Computer Inc 1 Infinite Loop Cupertino CA 95014 2084 USA 1 408 996 1010 http Awww apple com Apple the Apple logo Mac Macintosh and the Mac logo are trademarks of Apple Computer Inc registered in the U S and other countries Xserve is a trademark of Apple Computer Inc Xs
4. erve Dual Slot Riser Card 5
Download Pdf Manuals
Related Search