APC CTFRP User's Manual
Contents
1. BroadBand CTFRP WWW apo Ferroresonant Power Supply User Manual pe ee Arc DANGER HIGH VOLTAGE 990 5516A 10 2004 Chapter 1 General Information The CTFRP Series Power Supply provides a power source for broadband cable operations Important Safety Instructions Save These Instructions This Safety Guide contains important instructions that should be followed during installation and maintenance of the APC equipment and batteries It is intended for APC customers who setup install relocate or maintain APC equipment Changes and modifications to this unit not expressly approved by APC could void the warranty Failure to observe these warnings may result in serious injury death or damage to the equipment Electrical Do not work alone under hazardous conditions Warnings Do not handle any metallic connector before the power has been disconnected Servicing this equipment may require working with protective covers removed and AC power connected Use extreme caution during these procedures High short circuit current through conductive materials could cause severe burns When grounding cannot be verified disconnect the equipment from the utility power outlet before installing or connecting to other equipment Reconnect the power cord only after all connections are made Check that the power cord s plug s and sockets are in good condition Replacement of fuses or other parts must be with ident2. the Power Supply an APC approved enclosure must be installed and AC line voltage must be routed to the enclosure Local state federal and or National Electric Code NEC regulations regarding location permits and electrical wiring must be adhered to Do not operate the Power Supply where the temperature and humidity are outside the specified limits See Specifications in this manual Front View im ob Side View Arc DANGER VOLTAGE Installing the Power Supply Enclosure Installation Bottom View Qm Line Input gt Output Indicator __y Ground Lug m 1 Remove the screw holding the key on the rear of the chassis Remove the 10 32 Phillips mounting screw that secures the bracket to the housing Remove the mounting bracket from the housing by pulling down Set the Power Supply and the key aside pa de i Au Refer to Specifications in this manual for Power Supply dimensions 9 990 5516A 10 2004 6 Locate the position on the pole where the Power Supply is to be located 7 Drill two 3 4 holes vertically spaced 6 15 2 cm apart 8 Attach the top of the mounting bracket to the pole using a 5 8 pole bolt and washer Repeat this procedure for the bottom of the bracket 9 Ensure that the power supply enclosure is closed and locked 10 Holding the Power Supply above the bracket slide the unit down the bracket The lip of the bracket must slide under the lip at the top of the Power Supply c
3. Conformity Declared EN 60950 Application of Council Directives TAZVEEC Type of Equipment Power Surely Medel Numbers cover Manufacturer s Name nmd Address Poser Comeetion 132 Fairgrounds Road Weel Kingston Rhode Islam 28592 USA AX American Power Conversion A F C b v Business Park Galway Ireland American Power Conversion Main Avenue Rosario Cavite Philippines Amean Power Conversion 2nd Sireci Pem Cavite Economic Zone Rosario Cavite Philippines N Power Conversion Lot 32 Phase 1 Carrmelray industrial Park Canlubang Calamba Lugana Philippines AN APC Suzhau UPS Co Lad No 189 Suhong Road China Singapore Importers Name and Address Surhow Park Suxhou 219021 Hangu PRC American Power Comversien A P C b v Place Billera U S Ballybritt Business Park Galway Ireland Piste Galway Ireland qum d ETT Richard J Everett Sr Regulatory Compliance Engineer 5 Jan Ray 5 Ballard Managzng Director Europe Entire contents copyright 2002 by American Power Conversion Corporation All rights reserved Reproduction in whole or in part without permission is prohibited APC is a registered trademark of American Power Conversion Corporation All other trademarks are the property of their respective owners 8 990 5516A 10 2004
4. PUT FROM BREAKER 990 5516A 10 2004 CTFRP 90XXX Series possess 250V 20A Ait BK 16AWG BK 16AWG BLK WHT V 12AWG 90V OUTPUT 16AWG 16AWG ORN 1 60V OUTPUT VIO 120V BK W 18AWG 15uF G 18AWG 660V GREEN R 16AWG L 2 Turn the power supply switch to the ON position Note The output indicator located at the bottom of the unit is illuminated Initial Start up 1 Turn the utility breaker to the ON position 3 Using a True RMS voltmeter check for voltage at the stinger lug The unit is now operational To shut down the Power Supply 1 Move the power supply switch to the OFF position 2 Move the utility circuit breaker to the OFF position 6 990 5516A 10 2004 Chapter 4 Service Contact and Warranty Information Service APC makes every effort to ensure parts and equipment arrive in working condition Occasionally it may be necessary to return parts or equipment that are not in working condition If the unit requires service do not return it to the dealer Follow these steps 1 Contact APC Customer Support through the APC Web site www apc com support m Note the product model number the serial number and the date purchased If you call APC Customer Support a technician will ask you to describe the problem and try to solve it over the phone If this is not possible the technician will issue a Returned Material Authorization Number RMA m Ifthe product is under warrant
5. abinet 11 Replace the 10 32 Philips screw removed in step 2 above Wiring 1 Unlock the FRP enclosure Let the lid slide down and then pull out at the top The lid will remain attached to the Power Supply 2 Check the line power switch to ensure that it is OFF 3 Install a pin type connector not furnished in the chassis connector located on the bottom of the Power Supply 4 Attach the yellow wire with the clamp to the stinger of the pin connector Tighten the setscrew on the lug clamp 5 Place 6 copper ground wire into the ground lug located on the bottom of the cabinet PPP PPP Egg gg gg 6 Route and attach the ground wire according to local electrical codes 7 Install an approved 20 amp high magnetic circuit breaker on the input power side of the power supply 8 Install conduit into the opening on the bottom and attach line power in accordance with local electrical codes The barrier strip is wired with the hot leg at the top The bottom connector is chassis ground 4 990 5516A 10 2004 Chapter 3 Operation CTFRP 6X XX Series 370 T 1 C 1 380 14AWG BLK TW3 C1 15UF I4AWG BLK l4AwWG 412 App TW5 210 RN XEL 15 AWG 15 BREAKER SW OUTPUT OPTION 1 SW 1 2 SWI ERN 16 AWG JUMPERED IF NOT WHT USED 399 GRN YEL m Wes EL 12 AWG 4 16 AWG WS GRN YEL wd i DE 16AWG W2 we GRN YEL GRN BLK WHT GND 2 LT 1 LT 1 60 VAC RMS LL LINE IN OUTPUT TO CABLE IN
6. ical types and ratings Substitution of nonidentical parts may cause safety and fire hazards Overhead Never stand underneath anything while it is being hoisted Warnings Always wear a hard hat Lifting Transformer modules are heavy Use proper lifting techniques to avoid injury Warnings Unpacking Inspect the unit upon receipt Notify the carrier if there is damage The packaging is recyclable save it for reuse or dispose of it properly Check the package contents The package contains the Power Supply and product documentation 1 990 5516A 10 2004 Specifications Environmental Specifications Operating Temperature 40 F to 140 F 40 C to 60 C Humidity 5 to 95 noncondensing within enclosure Physical Specifications Characteristic Specification Height CTFRP6XXX 11 5 29 cm CTFRP9015 13 33 cm Width CTFRP6XXX 6 15 cm CTFRP9015 7 18 cm Depth CTFRP6XXX 6 15 cm CTFRP9015 9 5 24 cm Weight CTFRP6XXX 37 lbs 16 kg CTFRP9015 65 lbs 29 Models Supported CTFRP6009 FRP 120 VAC 60 Hz 60 V 9 A CTFRP6015 FRP 120 VAC 60 Hz 60 V 15 CTFRP6509 FRP 230 VAC 50 Hz 60 V 9 A CTFRP6515 FRP 230 VAC 50 Hz 60 V 15 CTFRP6615 0 FRP 240 VAC 60 Hz 60 V 15 CTFRP9015 0 FRP 120 VAC 60 Hz 90 V 15 2 990 5516A 10 2004 Chapter 2 Installation and Maintenance Only trained service personnel should install and maintain the Power Supply Prior to installing
7. rt Products must be returned with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase EXCEPT AS PROVIDED HEREIN AMERICAN POWER CONVERSION MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL APC BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically APC is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise Regulatory Approval 2002 C US EC Declaration of Conformity We the umdonagned declare under our sole responsibility that the equipment specified below conforms to the LISTED following standards and directives E191450 Standards to Which
8. y repairs are free If not there is a repair charge Procedures for servicing or returning products may vary internationally Refer to the APC Web site Select the appropriate country from the country selection field Select Support from the tab at the top of the web page 2 Pack the product in its original packaging If the original packing is not available refer to the APC Web site for information on obtaining appropriate packing materials m the unit properly to avoid damage in transit Never use Styrofoam beads for packaging Damage sustained in transit is not covered under warranty 3 Mark the RMA on the outside of the package 4 Return the unit by insured prepaid carrier to the address given to you by Customer Support How to Contact APC In the USA Outside the USA Refer to the APC Web site Refer to the APC Web site www apc com Select the appropriate WWwW apc com support country from the country selection field Select the Support tab at the top of the web page 7 990 5516A 10 2004 Limited Warranty American Power Conversion APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its own sole option any such defective products To obtain service under warranty you must obtain a Returned Material Authorization RMA number from customer suppo
Download Pdf Manuals
Related Search