Analog Devices ADXL345 User's Manual
Contents
1. To begin data acquisition click the Start Acq button in the bottom left corner of the screen To end data acquisition click the Stop Acq button in the bottom left corner of the screen Rev 0 Page 9 of 12 TEMPERATURE TAB The Temperature tab is used to examine the performance of the ADXL345 over temperature By plotting the acceleration vs temperature while the ADXL345 is not experiencing dynamic acceleration the offset temperature coefficient can be determined by taking the slope of the best fit line to the acceleration vs temperature data The inertial sensor evaluation system assists in the accuracy of this measurement by putting the accelerometer on a separate satellite Only the satellite has to be placed in an environmental chamber which eliminates inaccuracies due to the temperature effects of voltage sources converters and other biasing circuits The Temperature tab shown in Figure 15 allows a maximum number of points to be set and at what rate data is acquired The testing can be stopped before reaching the maximum number of points The data rate for the accelerometer can also be set to ensure that the testing is performed under conditions most like those that the part would be configured for in a system After selecting the values in the Sample Points Time Interval s and Data Rate Hz boxes data acquisition begins by clicking the Start Meas button When testing is in progress the Meas In Progress indicator2. Evaluation boards are only intended for device evaluation and not for production purposes Evaluation boards are supplied as is and without warranties of any kind express implied or statutory including but not limited to any implied warranty of merchantability or fitness for a particular purpose No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards Information furnished by Analog Devices is believed to be accurate and reliable However no responsibility is assumed by Analog Devices for its use nor for any infringements of patents or other rights of third parties that may result from its use Analog Devices reserves the right to change devices or specifications at any time without notice Trademarks and registered trademarks are the property of their respective owners Evaluation boards are not authorized to be used in life support devices or systems Rev 0 Page 12 of 12 2009 Analog Devices Inc All rights reserved Trademarks and registered trademarks are the property of their respective owners UG08119 0 6 09 0 www analog com
3. selection Ee ft fees irc p Aag wa COOH OI CI O D WEL Aesconce Mime 08119 007 Figure 10 Selecting the Correct COM Port for the ISEB After selecting the COM port click on Connect to connect to the ISEB This causes the indicator under Vs Set to light up and update the Current Vs V value verifying that the board is connected see Figure 11 ES ADS JAS Evaluation GUI Ele Rap ww GF fe Be Ga Gd Ge en Ge p x i J 08119 008 Figure 11 ISEB Connected to PC Clicking the round button above Vs Set causes the supply voltage Vs of the ADXL345 to be updated based on the value in the Desired Vs V box The Current uA and Temp degC boxes are also updated whenever the Vs Set button is clicked Read the contents of the ADXL345 registers by clicking the Read All Registers button in the Register Write box This action updates all register values and indicators on the right side of the screen Figure 11 depicts a sensor that is powered on with a DevID of 0xE5 a BW RATE value of 0x0A and an INT SOURCE value of 0x02 All other registers remain in their default state of 0x00 To write a value to a register select the register from the Target Register menu and click the D7 through DO indicators to set the value If an indicator is lit the value written to that bit is a Logic 1 whereas an unlit indicator indicates a Logic 0 When the register is configured correctly click the Write Register button to send the val
4. website www analog com To flash the ISEB microcontroller follow these steps 1 Ensure that the ISEB is connected to and detected by the PC The COM port that the device is recognized on must also be obtained as mentioned in the previous sections 2 Run the ARMWSD exe program located in the Drivers FW folder which displays information about the downloader as shown in Figure 7 ARMWSD File to download Browse Monitor Status Connect test board to PC COM4 at 115200 Baud Click Start Configure Start 08119 107 Figure 7 ISEB ARMWSD Firmware Downloader 3 Click Browse and select the ADI_ ISEB _FW_1_3 hex file located in the Drivers FW folder or the most recent firmware obtained from the Analog Devices website www analog com 4 Click Configure to display the screen shown in Figure 8 The downloader file should come configured for the ADuC7026 microcontroller on the ISEB The only option that may need to be changed is to select the correct COM port from the Serial Port menu on the Comms tab see Figure 8 When the COM port is selected click OK to accept the changes and go back to the main screen Configure Parts Help Comms lash Serial Port Baudrate 115200 08119 108 Figure 8 Selecting the Correct COM Port for the Downloader When the ISEB is connected the correct firmware is selected and the downloader is fully configured follow these steps to flash the firm
5. Figure 14 Power Consumption Tab When inactivity is detected caused by acceleration below the amount set in the THRESH_INACT mg box for the amount of time set in the TIME _INACT s box the accelerometer is placed into a lower data rate as set in the Inactive Data Rate Hz menu Because the power of the ADXL345 is modulated with data rate an immediate power savings is acheived When activity is detected an acceleration above that set in THRESH_ACT mg box the part is placed back into a higher data rate as specified in the Active Data Rate Hz menu Additionally the Micro In Calculation indicator lights up signifying that a controller or microprocessor is actively pulling data from the part or processing it In addition to power savings from the ADXL345 more power can be saved by powering down the microprocessor during periods of inactivity and using the ADXL345 activity interrupt to wake the microprocessor up during periods of activity The ACT INACT_CTL indicators can be used to enable different axes in the activity or inactivity events After updating the participating axes thresholds timers or data rates click the Configure Registers button The registers are not updated until the button is clicked Additionally the button updates the registers only when data acquisition is active If the button is clicked when no acquisition is occurring the button remains inactive until it is clicked again or until acquisition is started
6. enables it Note that no registers or parameters are updated after setting any individual box or indicator To configure the interrupts based on new values entered in this box you must click the Configure Interrupts button in the bottom right corner Clicking this button updates the Current Status indicators and configures the interrupts as set The INT _ SOURCE and ACT_TAP STATUS indicators are updated when an interrupt occurs The data ready DR watermark WM and overrun OR bits are always set because this tab does not service data related interrupts In the configuration shown in Figure 13 the accelerometer has detected inactivity If the accelerometer were moved with enough force to exceed the 504 mg activity threshold the INACT indicator would dim and the ACT indicator would light up If the accelerometer were put down and undisturbed for the 1 sec inactivity timer the ACT indicator would dim and the INACT indicator would again light up Rev 0 Page 8 of 12 POWER CONSUMPTION TAB The Power Consumption tab shows the advantages of using the inactivity and activity functions to modulate system power and obtain overall power savings see Figure 14 E ADMD 145 Cwalaation GU fie Gat Gere priwe ben Eeee ACDNACT_ETE iT Ad ASTAZI Poh Poh TA BI REM EM DIM Ac KEH YEN ZN SO000000 a DETA p para oumu Bor 1a Fita Daia ate HEj ee 2 389 8 OUTFT FATA D50 it 08119 011
7. lights up To end the test before the maximum number of points click the Stop Meas button E ADX1L345 Evaluation GUI miernugt Configuration Power Consumption Tongerse cos GA vos Mize BB 2009 08119 012 Figure 15 Temperature Tab The data in the top graph in Figure 15 is used for determining the offset temperature coefficient The bottom graph displays the temperature over time To save data a measurement cannot be in progress When the measurement ends or is stopped click the Save Data button to save the data to a txt file Rev 0 Page 10 of 12 HEADER PINOUT 3 3V P1 CS2 VS2 VS1 ST1 ST2 SCL1 SDA1 CLK MOSI MISO CS3 CS4 2 OO e el inl ot ft E e e e Eam EEn e eee een ee PE CE cy Se Feed ee es ea ee Ree m eL mra A R E E E E E E A E E a f D E S a E E D aa mw C T E E E E D Ea E ele Sees eee I ea a E E E A M D ee P Ece ee A L mw a EY EE UDa AGND GND Y Figure 16 ISEB 20 Pin Header Pinout ESD CAUTION ESD electrostatic discharge sensitive device Charged devices and circuit boards can discharge without detection Although this product features patented or proprietary protection circuitry damage may occur on devices subjected to high energy ESD Therefore proper ESD precautions should be taken to avoid performance degradation or loss of functionality Rev 0 Page 11 of 12 08119 013 NOTES
8. you can begin real time measurement by clicking the Start Meas button This causes many of the options and tabs to be grayed out or to disappear to prevent software conflicts until the Stop Meas button is clicked The accelerometer output data then begins to flow across the screen at the selected output data rate Up to the last 8192 samples x y and z axis of accelerometer output data can be saved to a txt file Each file created contains a header with the date bias values and accelerometer data in LSBs aligned in tab delimited columns To save the data you must enable the Save Data button Click this button and type in or select a file name with a txt extension Each time a measurement is performed the new data is appended to the old data This means that saving data also saves old data if new data is less than 8192 samples unless the old data is first cleared The data saved to a file is the LSB data therefore the Output LSB window must be cleared so that old data is not saved To clear the Output LSB window right click the x axis labeled Sample in the space between Sample and the window and select the Clear Chart option Rev 0 Page 7 of 12 INTERRUPT CONFIGURATION TAB The Interrupt Configuration tab is used to demonstrate the built in functions of the ADXL345 By selecting the functions to enable and configuring the appropriate parameters the benefits and uses of the interrupts can be examined This tab is u
9. ADI Inertial Sensor Evaluation System oF came with an installation CD your hardware lt 6 or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Figure 2 Found New Hardware Prompt 08119 002 3 Select Don t search I will choose the driver to install see Figure 3 and select ADI Inertial Sensor Evaluation System from the model list see Figure 4 The ISEB should be detected automatically in the Device Manager as the ADI Inertial Sensor Evaluation System under the Ports COM amp LPT selection It is recommended to open the Device Manager to verify hardware detection and to record the communication port associated with the ISEB for use in the GUI Found New Hardware Wizard Please choose your search and installation options Pha tae 7V Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware 081 19 003 Figure 3 Selection of the Driver to Install Found New Hardware Wizard Select the device driver you want to install for this hardware Fata V Sele
10. ANALOG DEVICES Evaluation Board User Guide UG 015 One Technology Way P O Box 9106 Norwood MA 02062 9106 U S A Tel 781 329 4700 Fax 781 461 3113 www analog com IMEMS ADXL345 Inertial Sensor Evaluation System FEATURES Ultralow power ADXL345 accelerometer Inertial sensor evaluation board Inertial sensor specific satellite for evaluation Standard USB cable for power and communications PC based graphical user interface GUI Separates DUT from controller for accurate environmental testing GENERAL DESCRIPTION The iMEMS ADXL345 inertial sensor evaluation system is an easy to use evaluation tool targeting bench or desktop characterization of Analog Devices Inc inertial sensor products The system consists of the inertial sensor evaluation board ISEB or main board and a satellite board for any Analog Devices inertial sensor product The ISEB connects directly to a PC via its USB where the USB connection provides both power and communications to the board The ISEB then connects to the satellite board through a ribbon cable This cable allows the satellite to be easily manipulated for testing or for being separately placed into an environmental chamber for temperature or humidity testing Separating the boards mitigates corruption of data due to the temperature and humidity effects of other components Please see the last page for an important warning and disclaimers 08119 001 Figure 1 Inert
11. W2 which is shown in Figure 9 to reset the ISEB and have it detect the currently connected satellite This must be done when the satellite connected to the ISEB is replaced by a satellite of a different part only replacing the satellite with a satellite for the same part that is an EVAL ADXL345Z S with another EVAL ADXL345Z S does not require SW2 to be pressed The inertial sensor evaluation system GUI is opened by executing the ADXL345 Evaluation GUL exe file located in the ADXL345 Evaluation GUI folder To exit the GUI use the Stop VI button to disconnect from the ISEB Then exit the application by selecting File and Exit or by pressing Ctrl Q The first screen brought up is the Configuration tab see Figure 10 This screen is used for manual configuration of the sensor for setting up the communication port between the PC and ISEB and for setting the sensor voltage values Configuration register values can be saved and reloaded It is important to note that the register settings entered on this screen are independent from other GUI screens Each screen requires a different register setup and any values that can be altered are made available for that particular screen With the Configuration tab open select the correct COM port for the ISEB from the VISA Resource Name menu see Figure 10 The correct COM port can be found by checking the Device Manager for the ADI Inertial Sensor Evaluation System under the Ports COM amp LPT
12. ct the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver you want to install click Have Disk Show compatible hardware ADI Inertial Sensor Evaluation System A This driver is not digitally signed Tell me why driver signing is important Figure 4 Selection of the ADI Inertial Sensor Evaluation System Drivers Installing the LabVIEW and NI VISA Run Time Engines After installing the USB drivers install the LabVIEW and NI VISA run time engines To ensure that the drivers are installed 08119 004 properly it is recommended that you reboot when prompted 1 Execute the LVRTE851std exe file located in the Drivers folder 2 Follow the on screen instructions to complete installation of the LabVIEW run time engine 3 Reboot the PC 4 Locate and execute the visa441runtime exe file located in the Drivers folder to install the NI VISA run time engine 5 Follow the on screen instructions to complete the installation 6 Reboot the PC Rev 0 Page 3 of 12 HARDWARE CONFIGURATION To configure the hardware follow these steps 1 Plug the USB A to Mini B cable into the PC if the cable is not already connected 2 Connect the ISEB to the USB cable If prompted to install the device see the Software Configuration section for details on how to install and select the correct driver 3 Connect the ISEB to the ADXL345 satellite using the 18 inch 20 pin r
13. eeseseeceseseeeeeeeeeeeseseeeeeesees 8 Power CONSUMI PEON TaD eresse asao 9 Temperature VAD is evaccsegveccsaqeviccdaceeectuncaausevadasseeiecersnersiesneesseose 10 FC Ae BF UNO 5 cg eis od cats ta ase secant cau R 11 PS VIG EOIN cated cet cate i ol a cal eal EEEE 11 Rev 0 Page 2 of 12 INERTIAL SENSOR EVALUATION SYSTEM SETUP SOFTWARE CONFIGURATION Software configuration of the inertial sensor evaluation system involves installation of USB drivers for the ISEB and National Instruments LabVIEW Run Time and NI VISA Run Time files These are available in the Drivers folder on the packaged CD Installing the USB Drivers for the ISEB To install the USB drivers follow these steps 1 Execute the ADI ISEB USB_Drivers exe file located in Drivers ISEB_USB 2 Follow the on screen instructions to install the drivers 3 Click Continue Anyway when prompted that the drivers are not tested It may be necessary to manually select the correct drivers after installation To select the drivers follow these steps 1 Connect the USB A to Mini B cable to the PC and then to the ISEB The satellite board does not need to be connected for this step New hardware is detected upon completion of this step 2 If prompted to install drivers again click Install from a list or specific location Advanced see Figure 2 Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for
14. ial Sensor Evaluation System The ISEB is a universal main board and is intended to be used with various satellites of Analog Devices inertial sensors including analog and digital accelerometers as well as gyroscopes The different products are evaluated by means of separate GUIs that are customized for performance and characterization measurements relevant to the inertial sensor being evaluated The EVAL ADXL345Z M system contains the ISEB and the EVAL ADXL345Z S satellite Also included is a USB A to Mini B cable to connect the ISEB to a PC and an 18 inch 20 pin ribbon cable to connect the ISEB to the satellite A CD is also included with the necessary drivers and executables to use the system and to quickly begin evaluating the ADXL345 Rev 0 Page 1 of 12 TABLE OF CONTENTS PO AUUIE CS nena nonn A General Descriere ne tacmenes TSCM ISUO I FASC 8s sees tsar cay secu Paracas sas cts Acree asco aaron aise Inertial Sensor Evaluation System Setup eeeseeeeteeeeeeeeees Software CONT OULAliON sea5sescieyscesdieycsevavessvantdevcdevieessaevesepscnsivarede Hardware COmtie ur atin sisirain R Updating Repairing the ISEB Firmware teseeeeeseeeeeeeees Inertial Sensor Evaluation System Graphical User Interface REVISION HISTORY 6 09 Revision 0 Initial Revision Configuration aD coccencueen nae sawn nannies 6 Real Time Measurement Tab 00 ec cccecesesseteeceeceseeeeseeeeseeeeaeees 7 Interrupt Configuration Tab e
15. ibbon cable This cable is keyed to prevent inserting it backwards and causing damage to the system 4 Connect the ADXL345 satellite to the opposite end of the ribbon cable 5 Verify that the jumpers located in the center of the ADXL345 satellite are configured as shown in Figure 5 JUMPER POSITIONS i a t ADXL345 08119 005 Figure 5 Correct Jumper Positions for the ADXL345 Satellite 6 Place the ADXL345 ultralow power accelerometer into the socket on the satellite board The Socket Pin 1 Indicator is located inside the socket close to the hinge as shown in Figure 6 This pin indicator should match up with the Pin 1 Indicator on the ADXL345 7 After positioning the ADXL345 in the socket firmly close the socket until it latches ADXL345 SOCKET PIN 1 INDICATOR ADXL345 ACCELEROMETER PIN 1 INDICATOR 08119 006 Figure 6 Location of Pin 1 Indicators for the ADXL345 Accelerometer and Socket The inertial sensor evaluation system should now be set up and ready to use Rev 0 Page 4 of 12 UPDATING REPAIRING THE ISEB FIRMWARE In the event that the ISEB firmware becomes corrupted or must be updated the CD contains the necessary programming utility to flash the ISEB microcontroller Also available on the CD is the version of firmware available at the time of release of the EVAL ADXL345Z M system Version 1 3 In addition as new firmware is made available it can be downloaded from the Analog Devices
16. pdated whenever an interrupt occurs This means that some interrupts such as inactivity if enabled alone will not appear to be updated NT DS TAF OTAP ACT MA T PF WU OR 6098080800 ATTAR STATIS WACT ZAcT atar TAF aF 00000000 ACTARACT_OTk A ZEN AC MEH YEH IEN TAP ANG b ie vi Hi 08119 010 Figure 13 Interrupt Configuration Tab The Current Status indicators are updated when the panel is first activated and when the Configure Interrupts button is clicked They show the register values at the time of the read The Interrupt System Parameters box is used to set the built in interrupt parameters Here the thresholds for tap or activity events can be set as well as the many timer values for the interrupt parameters The units of each are shown after the register parameter name and entered values are automatically rounded to the nearest valid value The indicators for ACT_INACT_CTL and TAP AXIS are used to select the axes to include in activity inactivity and tap events For more details refer to the ADXL345 data sheet Clicking an indicator causes it to toggle values A lit indicator causes a value of 1 to be written to that bit and an unlit indicator causes a value of 0 to be written to that bit In the Interrupt Configuration box you can select the interrupts to enable For purposes of the GUI all enabled interrupts are mapped to the INT2 pin Selecting the checkbox next to the appropriate interrupt
17. ting 1024 on the y axis and typing 2048 adjusts the scale to show 2048 LSBs to 1024 LSBs The configuration section is at the bottom of the Real Time Measurement tab In the Data Rate and Resolution box the output data rate and g range can be adjusted Selecting the Full Resolution checkbox places the part into full resolution mode where the scale factor is fixed Deselecting this checkbox places the part into fixed 10 bit mode For more information about the operation of the part refer to the ADXL345 data sheet The Self Test button toggles the self test bit of the ADXL345 When self test is activated the sensor beam is deflected The electronics detect this by means of a shift in all three axes When self test is enabled the indicator next to the Self Test button is lit Clicking the Self Test button when self test is enabled turns the self test feature off and causes the Self Test indicator to dim Self test is enabled as long as the indicator is lit The ADXL345 provides three offset registers that are used for calibration and offset adjustment On the Real Time Measurement tab these registers are easily accessible for programming offset values This can be done in the Offset Adjustment box by typing a value into the text box below the corresponding axis knob or by clicking and holding the knob and rotating it on the screen with the mouse cursor The value entered is directly written into the offset registers After configuration
18. ue to the ADXL345 Note that the D7 through DO indicators under Target Register are not updated based on the value stored in that register To save a configuration click the Save Config button in the Configuration File box see Figure 11 Save the file with a txt extension After a configuration is saved you can load the configuration back into the device by clicking the Load Config button and selecting the configuration file Rev 0 Page 6 of 12 REAL TIME MEASUREMENT TAB The Real Time Measurement tab configures the inertial sensor evaluation system and the ADXL345 for real time acceleration monitoring The tab contains an oscilloscope like interface that you can use to view the output of the accelerometer and adjust the relevant parameters such as bandwidth range and offset see Figure 12 Bie at ppm Drow feb Ceigean pet Top Papierem aaea Canip Prone Cariamae Temperate em aT a IT Ta ALCI Daa wj TABLE Gabe AE Barr VER CTL Gate oo Coo Fo BE Ban F Pe Et 08119 009 Figure 12 Real Time Measurement Tab Within the Real Time Measurement tab additional tabs exist for displaying the output in terms of least significant bits LSBs or acceleration in gs In the Output LSB tab the output range can be adjusted by using the graph tools in the upper right corner or by selecting the x axis labeled Sample or y axis labeled Output LSB limits and typing a new value For example selec
19. ware 1 Click Start as shown in Figure 7 to initiate the flashing process After clicking Start the two buttons on the ISEB shown in Figure 9 must be pressed in a specific order to flash the firmware amp ADuC7026 SW1 SW2 081 19 109 Figure 9 ISEB Switch Locations for Flashing the Microcontroller 2 Press and hold down SWI 3 With SW1 held down press and release SW2 4 Release SW1 The download then begins and is automatically verified by the downloader If the downloading process fails which will be indicated in the Monitor Status box see Figure 7 attempt the download again by clicking Start and then the appropriate switch combination It may take a few attempts to reprogram the board successfully After the download is completed successfully click Run as shown in Figure 7 to reset the ISEB and to begin running the new firm ware When this step is complete the board is updated correctly Updating the firmware may require that a new evaluation GUI be obtained If the firmware on the CD is used to flash the ISEB the evaluation GUI on the corresponding CD is sufficient If the firmware used is obtained from the Analog Devices website www analog com the most recent version of the evaluation GUI which is also located on the website should be used Rev 0 Page 5 of 12 INERTIAL SENSOR EVALUATION SYSTEM GRAPHICAL USER INTERFACE CONFIGURATION TAB When the system is set up and configured press S
Download Pdf Manuals
Related Search