AMX UDM-0404 User's Manual
Contents
1. 252 b Hub name na FIG 3 Network Settings Note All changes are immediate once the IP address of the hub has been changed redirect the web browser to the changed address Restoring Hub Configuration and Connections on Power Up To ensure the configuration settings for the Hub are retained each time the hub boots ensure the Restore configuration on power up and Restore connections on power up options at the bottom of the Setup page have been enabled FIG 4 Restore configuration on power up Restore connections on power up FIG 4 Restoring configuration on power up Note Failure to select the Restore Configuration and Connection options will mean the Hub configuration and connections will need to be re configured if the Hub is reset Hub Reset To reset the Hub Click the Reset Hub button FIG 4 Note A power down of the Hub is required to complete the reset procedure For full warranty information refer to the AMX Instruction Manual s associated with your Product s 2 08 2008 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 www amx com Input Configuration The options on the nputs page allow you to specify the video types and audio sources being presented to each2. an EX Overview The UDM 0404 Endeleo Multi format Distribution Hub FG UDM 0404 delivers any video source including Component RGB VGA and S Video to a virtually unlimited number of display devices The UDM 0404 FIG 1 supports 4 high resolution input ports and 4 UDM output ports and supports multiple methods of delivering sync information between the UDM hub and the display device including common mode UDM OUTPUT Ports RJ 45 EMDELED WDM oand Input connections IR TX connections for locally connected devices Serial port RJ 12 ETHERNET port RJ 45 FIG 1 UDM 0404 In total the UDM 0404 system can distribute any combination of the following 4 RGBHV sources 4 Component video sources 4 S Video sources or 12 Composite video sources Source inputs to the UDM are industry standard VGA Composite Component or S Video feed and output is presented as an RJ45 port for connection to Cat5 5e or 6 twisted pair Ethernet cable Video inputs are connected via the HD15 Input connector on the rear of the UDM Adapters are used to bring the different types of video source into the UDM Each UDM has an Ethernet network port to provide connectivity to a central management system or can be controlled by the onboard configuration pages A Serial connection is also provided for CLI administration and diagnostic purposes Features e 4 multi format inputs x 4 outputs Supports multiple methods of delivering sync including Com
3. UDM For example connect to the Video In connection on Input A of the Hub 3 Connect any audio to the analog RCA audio connectors or digital SPDIF connector Note Ensure Input A is configured as a VGA Inpu and named appropriately within the Inputs section of the Configuration software Also ensure the correct Audio Type Analog L R or S PDIF is selected for the relevant input Connecting a Composite Video Input 1 Connect the UDM HD15RCA3 Breakout Cable FG HD15RCA3 not included to the source device s Composite output ports A1 red RCA A2 green RCA A3 blue RCA 2 Attach the other end of the cable to the appropriate VIDEO IN connection on the UDM 3 Connect any audio to the analog RCA audio connectors or digital SPDIF connector Connecting a Component Video Input 1 Connect the UDM HD15RCA3 Breakout Cable FG HD15RCA3 not included to the video source device s Component video output connectors Red Green and Blue 2 Attach the other end of the cable to the appropriate VIDEO IN connection on the UDM 3 Connect any audio to the analog RCA audio connectors or digital SPDIF connector Connecting an S Video Input 1 Connect the UDM SVID01 HD 15 to SVideo cable FG UDM SVID01 not included to the video source s S Video connection 2 Attach the other end of the cable to the appropriate VIDEO IN connection on the UDM 3 Connect any audio to the analog RCA audio connectors or dig
4. 0404 Endeleo Multi Format Distribution Hub Audio amp Video Formats Resolutions Distance Audio amp Video Formats Resolutions Distance Format Name UDMRXOI UDMRXO Class Composite Component 1920x1080 1080p 120 m 400 300 m 1000 640x480 VGA 200 m 650 300 m 1000 800x600 SVGA 200 m 650 300 m 1000 1024x768 200 m 650 300 m 1000 1280x1024 SXGA 150 m 500 300 m 1000 1600x1200 UXGA 120 m 400 300 m 1000 When using VGA modes with audio enabled the maximum cable distance is approximately 200 m 650 UDM RX02 Note The maximum distances indicated above are not absolute but are recommended distances that have been tested to deliver video at the specified resolutions without significant signal degradation In particular lower resolutions 640 x 480 720 x 480 and 800 x 600 can often be delivered significantly further than what is indicated in the table Refer to the UDM 0404 Endeleo Multi format Distribution Hub Operation Reference Guide for additional details on maximum cable distances A V Source Input Connectors There are 4 sets of input connectors to the rear panel of the UDM 0404 labelled A D see FIG 1 that allow the UDM 0404 to connect to A V source devices Connecting a VGA Video Input 1 Connect one end of a VGA cable to the source device s VGA output port 2 Attach the other end of the cable to the appropriate VIDEO IN connection on the
5. Distribution Hub Operation Reference Guide for information on input configuration user control passthrough mode video compensation date time configuration creating scheduled events and scheduled presets Connecting to the UDM 0404 1 With the TCP IP address configured connect the UDM 0404 to your network equipment switch hub or serial port or if required use an Ethernet Cross over cable to connect your PC directly 2 Enter the IP address into the address field within a browser window The default IP address of the UDM 0404 is 192 168 0 96 3 To connect to the UDM 0404 a password is required FIG 2 Connect to 192 168 224 141 endeleo User name E ecooo Password C Remember my password FIG 2 Endeleo Login screen eThe username should be left blank The password is admin The password is case sensitive 4 On initial connection the Status page is displayed Network Configuration Hubs can be configured for the network environment using the Setup page Note The UDM 0404 does not support DHCP Always configure a static IP Address 1 Specify the following network options for the Hub a Hub IP Address Subnet Mask and Default Gateway b UDP Port default 2008 c Hub name maximum of 30 characters 2 Click on Update to save the new settings to the Hub FIG 3 F address hs es pa 193 UDP Port 2008 Gateway 192 hes 244 2 Subnet mask EN 255
6. ick Green and the Red setting will reappear Each radio button corresponds to a 4ns nano second delay 9 Repeat this display setup for each active screen connected to the UDM Port 3 version 01 15 User control Send settings to RX Default Remote type UDM RC02 W Port name Pot 3 Dual output Bright Up Dovm 25 Sharp Up Dovm 6 Advanced Sync Common pil ed skew OOOOOOOOOOO0O00O 0 Protocol None FIG 6 Calibrating and Compensating Receive Units aF 93 UDM 0404 REV B TUL LILLE TLL Ev
7. input port and where appropriate renaming these 1 Select the Inputs link at the top of the Status page to invoke the Input Configu ration page FIG 5 Input ype Name Audio A Component A1 Analog UR B S Video B1 SPDF V Control Port Input FIG 5 Input Configuration page 2 Use the Type drop down menus to select the appropriate Input Type for each input For VGA Component S Video and Composite inputs only one connection is possible per input port elf the Input Type is Composite then the screen will refresh and enable the administrator to name each of the 3 available composite sources separately 3 Name the input Type s appropriately Configuring Audio Types For Inputs Audio types Analog L R or S PDIF can be configured for each Input To configure audio for individual Inputs 1 Select the Inputs option from the available options at the top of the Status page 2 Select the appropriate Audio type Analog L R or S PDIF lf Composite is selected as the Input type only one audio source will be available Ensure audio has been connected from the Input to the rear of the hub Ensure the connections are sound and fixed correctly Naming Ports The Status option displays the currently connected sources what source each display is showing Click the Status option For each of the 16 ports click the Port Name hyperlink and define the port name e g Reception Lobby etc Calibrating and Compensa
8. ital SPDIF connector Device Connectivity IR TX1 2 and TX3 4 Ports A maximum of 4 Devices such as DVD players or VCRs can be connected to the UDM Hub and controlled through the Browser software or via a remote control An optional IR02 IR splitter cable FG IR02 may be required 1 Connect an Endeleo IR Emitter Module FG IR01 to the relevant IRTX port at the rear of the Hub 2 Run the other end of the IR Emitter to the device s IR sensor and attach the bud to the device s sensor by removing the cover of the reverse side of the bud IR commands for each device on the system have to be learned by the Hub in order to function properly Refer to the Protocols and IR section of the UDM 0404 Operation Reference Guide on how to learn a device s IR commands Connecting UDM RX01 RX02 Receivers to the UDM 0404 1 Connect a standard Cat5 6 cable to the port marked UDM on the UDM Hub 2 Connect the other end of the Cat5 6 cable to the UDM Hub port on the UDM RX01 or RX02 Receiver 3 When the power is switched on 2 LEDs will be visible at the Hub port Amber phantom power enabled and Green UDM receiver connected to Hub port Configuration Overview Each UDM Hub can be configured for the correct network environment It is also possible to configure each Hub for the correct date and time Configuration options are available via the UDM Hub s built in Browser Interface Refer to the UDM 0404 Endeleo Multi Format
9. mon Mode Sync Digital audio support Central device control 1U rack mounting Compatibility The UDM 0404 is compatible for use with UDM RX01 FG UDM RX01 and UDM RX02 FG UDM RX02 Receivers Note Common Mode Sync delivery is supported only on the UDM Rx02 Product Specifications UDM 0404 Specifications Power Requirements 3 PIN IEC 90 264v AC140 W Network Interface 10baseT Serial Interface 9600 8 N 1 Max Video Input e 4x RGBHV or e 4x S Video or e 12x CVBS Electrical RJ 45 indicating power to receiver and link status Operating Environment 35 F 95 F 5 C 35 C e Max relative humidity 85 non condensing Dimensions HWD 1 3 4 x 19 x 12 1 2 45 mm x 440 mm x 320 mm om AK Certifications e CE UL FCC part 15 Class A Included Accessories IEC power cord e 6 Ethernet Crossover Cable e 19 mounting brackets e RS232 DB9 RJ12 Connection Cable FG RSO1 e RO3 External Infrared Receiver Module FG IRO3 e UDM RC10 IR Engineering Remote Control FG UDM RC10 Note No A V interface cables supplied HD15 to S Video Cable FG UDM SVID01 HD15 to 3x RCA Breakout Cable FG HD15RCA3 RS232 DB9 RJ12 Connection Cable FG RSO1 UDM RX01 Multi Format Receiver FG UDM RX01 UDM RX02 Multi Format Receiver FG UDM RX02 IRO1 IR Emitter Module FG IRO1 IRO2 IR Splitter Cable FG IRO2 IRO3 External IR Receiver Module FG IRO3 Other AMX Equipment Quick Start Guide UDM
10. ting Receive Units Each Receive unit must be compensated for distance Brightness Sharpness and skew R G B depending on the length and type of UTP cable Cat5 Cat5e Cat6 being used 1 Connect a known good source input to all ports Click the Include All link on the Status page this will highlight all 4 port lines in blue 2 On the top dark grey Included bar select a source to connect to by selecting a Source Name from the drop down list If you have a VGA source select this source 3 Click the Execute link and all displays will now display the selected source 4 Depending on the calibration of the Receive Module the image may appear dim bright sharp fuzzy or possibly not at all 5 From the Status page click the Port Name hyperlink and then click the Advanced checkbox Brightness Sharpness and R G and B skew delays can be adjusted manually 6 In this screen Sync handling capabilities can also be adjusted By default Common Mode Sync delivery is the default Define as Auto if you don t know but if no image appears you may need to select Sync on Green 7 Adjust Brightness until you can see a bright image and Sharpness to focus the image correctly Values can be changed by either using the Up and Down but tons or by typing the value 0 255 in the editable text box 8 Then adjust Red Green and Blue Skew settings click Red link and the Blue setting will appear click Blue and the Green setting will appear and cl
Download Pdf Manuals
Related Search