Ameristep RAPTOR TRIPOD 7700 User's Manual
Contents
1. fq A CAUTION Make sure tripod legs are on level ground at all times A Step 12 Once tripod has been set up at desired hunting location use 4 GROUND STAKES to hold tripod in place Each leg has a foot with one hole A for each Ground Stake to be driven through The feet on Bottom Ladder f f Section one hole on each foot for remaining two stakes to be driven through DISMANTLING TRIPOD Step 1 Dismantle TRUSS SYSTEM by unhooking S HOOK BRACE STRAPS from STABILIZER BAR loosen TRUSS STRAPS and remove CABLE Step 2 Gently tip tripod over on its side Step 3 Depress spring loaded buttons on each leg where MIDDLE LEGS meet UPPER LEGS Separate MIDDLE and LOWER LEG SECTIONS from UPPER LEGS fig 3 Depress spring loaded buttons that adjust leg height between MIDDLE and LOWER LEGS and slide leg sections together and lock them at shortest length fig 3a Step 4 Remove LOWER and MIDDLE LEG SECTIONS Step 5 Remove D CLIPS holding UPPER LEGS to PLATFORM and Step 6 Remove Shooting Rail by push button to release UPPER LEGS from CONNECTION BASE depressing button and sliding Rail out page 10 2008 rev 6 08 Ameristep Inc 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com me RAPTOR TRIPOD Model 7700 Step 8 Place CABLE in seat cushion pocket for transport Install BackPack Straps as shown above Step 7 Fold up remaining assembled portion Step 9 Stack2. Aimeeis TEP NON TYPIGAL RAPTOR TRIPOD Instruction and Safety Manual Model 7700 Thank You for purchasing Ameristep Non Typical RAPTOR TRIPOD CAUTION Maximum Tested Weight Capacity Limit for this Product is 300 POUNDS Including Accessories Gear and Attire DO NOT Exceed tested weight limit capacity This product is designed for only ONE PERSON A WARNING Every year serious injury and even death occurs from hunting related falls To ensure your safety please COMPLETELY read and follow this safety manual and ALL warning labels BEFORE assembling installing or utilizing this product DO NOT USE THIS AMERISTEP PRODUCT BEFORE FULLY UNDERSTANDING ALL SAFETY WARNINGS AND INSTRUCTIONS IF YOU HAVE QUESTIONS ARE UNSURE ABOUT ANY INFORMATION or NEED ADDITIONAL INFORMATION CONCERNING THIS PRODUCT CONTACT OUR CUSTOMER SERVICE DEPARTMENT KEEP AND MAINTAIN THIS SAFETY amp INSTRUCTION MANUAL FOR FUTURE REFERENCE 2008 rev 6 08 SAFETY MUST BE YOUR FIRST PRIORITY WITH THIS PRODUCT TREE LADDER STAND SAFETY INSTRUCTIONS WARNINGS Please read the following instruction manual and warning labels completely before utilizing this product Failure to understand and execute these instructions and warnings may result in serious injury or death KEEP THIS INSTRUCTION MANUAL IN A SAFE PLACE AND REVIEW ANNUALLY e ALWAYS read and understand these WARNINGS amp INSTRUCTIONS before using this product each se
3. 2 Middle Leg 1 Middle Ladder Section GE 0 2 Bottom Leg Step 6 Slide each of 2 MIDDLE LEGS into bottom of TOP LEGS by depressing spring loaded button until each leg section snaps into corresponding hole in TOP LEG as shown Slide MIDDLE LADDER SECTION into bottom of TOP LADDER SECTION Make sure brackets at bottom of MIDDLE LADDER SECTION face inward Make sure as each ladder section is slid together each ladder section has slid fully into its corresponding ladder section Step 7 Slide each of 2 BOTTOM LEGS into bottom of MIDDLE LEGS by depressing spring loaded button until each leg section snaps into corresponding FIFTH HOLE from bottom of MIDDLE LEGS Make sure button is in fifth hole in bottom section initially as this will make platform level on level ground Once tripod is set up use multiple adjustment holes to level tripod if ground is uneven 2008 rev 6 08 Page 7 Ameristep Inc 901 Tacoma Ct P O Box 189 e Clio MI 48420 810 686 4035 www ameristep com me RAPTOR TRIPOD Model 7700 NOTE You will need TAg 2 8 2 S Hook Brace Strap Esseg 1 Stabilizer Bar uckle Loop 2 Buckle Strap 2 M8 x 40mm HEX BOLT 3 Washers 1 Lock Nut Step 8 Mount STABILIZER BAR to brackets using 2 M8 x 40 mm bolts Step 9 TRUSS SYSTEM Attach BUCKLE STRAPS to PLATFORM fig 9 BUCKLE STRAP Oh Onei He ECH and Bottom of BOTTOM LADD
4. F This warranty gives you the specific legal rights You may also have other rights that vary from state to state This agreement shall be governed by the laws of the State of Michigan United States of America SAuceis TEP See our Full Line of Products Accessories and Replacement Parts at Www ameristep com 2008 rev 6 08 Ameristep Inc 901 Tacoma Ct P O Box 189 e Clio MI 48420 810 686 4035 www ameristep com
5. SHOOTING REST PADS Ameristep Inc 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com me RAPTOR TRIPOD A Model 7700 NOTE You will need GQ p A rm GESSI 1 Left Platform A eee A 1 Top Ladder Section 1 Right Platform 2 M8 x 75mm HEX BOLT 3 Washers 1 Lock Nut 2 M8 x 70mm HEX BOLT 2 Washers 1 Lock Nut 2 M8 x 70mm HEX BOLT 3 Washers 1 Lock Nut Step 4 Assemble PLATFORM by putting RIGHT and LEFT PLATFORM Step 5 Mount 2 TOP LEGS and TOP LADDER SECTION to CONNECTION BASE SECTIONS sections together and bolting them with 2 M8 x 70 mm bolts by passing TOP LEGS through PLATFORM sliding them into CONNECTION BASE Mount FOOTREST to front of PLATFORM using 2 M8 x 70 mm bolts with Depress spring loaded button on each TOP LEG until button snaps into hole in welded stoppers underneath PLATFORM CONNECTION BASE port Line up holes in each Top Leg with corresponding hole in PLATFORM and lock Legs to PLATFORM using D CLIPS one for each leg Step 5a Bolt TOP LADDER SECTION to CONNECTION BASE using 2 M8 x 45 mm bolts fig 5a Then bolt TOP LADDER SECTION to PLATFORM using 2 M8 x 75 mm bolts fig 5b 2008 rev 6 08 Page 6 Ameristep Inc 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com TRIPOD LEGS me RAPTOR TRIPOD Model 7700 NOTE You will need ee g t ay C A ES J
6. BOLT Buckle L 3 Washers 1 Lock Nut Za ee 2 Buckle Strap 2 S Hook Brace Strap 2 M8 x 70mm HEX BOLT 2 Washers 1 Lock Nut 1 Seat Back Cushion 1 Seat Cushion 4 M8 x 70mm HEX BOLT 3 Washers 1 Lock Nut 1 Shooting Rail Cover 4 Ground Stakes E 2 M8 x 75mm HEX BOLT WRENCH 2 3 Washers 1 Lock Nut 2 b Clips 2008 rev 6 08 Page 4 Ameristep Inc 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com PLATFORM ASSEMBLY me RAPTOR TRIPOD Model 7700 NOTE You will need 1 Seat Frame Base F 1 Seat Frame gt 1 5 Swivel Washer f 1 M8 x 30mm HEX BOLT 1 Seat Back Cushion 2 Washers 1 Lock Nut 1 Seat Cushion Te VS j po va 1 Shooting Rail Cover 1 Shooting Rest Pad 1 Shooting Rail Connection 1 Back Rest 1 Shooting Rail Step 1 Seat Frame to Connection Base with 5 5 Washer in between them using 1 M8 x 30 mm bolt Step 2 Mount BACK REST to SEAT FRAME using 2 M8 x 70 mm bolts Assemble SHOOTING REST by inserting SHOOTING REST into SHOOTING REST CONNECTION then inserting assembled SHOOTING REST SYSTEM into SEAT FRAME Sliding each part of SHOOTING REST SYSTEM requires depressing spring loaded buttons which are also used to adjust SHOOTING REST to desired position 2008 rev 6 08 Page 5 Step 3 Slide on SEAT CUSHION SEAT BACK CUSHION and
7. ER EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THE PRODUCT Ill EXCLUSIONS LIMITATIONS AND CONDITIONS OF LIMITED WARRANTY A This warranty cannot be assigned or transferred B This warranty only applies if the Ameristep product is used in accordance with Ameristep s written instructions C Ameristep products are intended only for use in hunting Ameristep products are not intended or authorized for use in any situations that may create health or injury risks D This warranty is void if the product is damaged through abuse accident improper use negligence or normal wear amp tear E This warranty is void if the product is altered changed or modified in any manner F This warranty is void if any attempt is made to repair the product without written authorization from Ameristep G Except as provided in this limited warranty all Ameristep products are provided as is All other warranties and representations oral or written express or implied including but not limited to any implied warranties of merchantability or fitness for a particular purpose are excluded and do not apply IV PROCEDURES IN EVENT OF DEFECT A If you find a product to be defective contact Ameristep at 1 810 686 4035 B When you receive authorization from Ameristep return the product as directed by Ameristep V LIMITATION OF DAMAGES A Ameristep shall not under any circum
8. ER SECTION fig 9a BUCKLE LOOP on other side d YY x lt Strap at Bottom Ladder Section Strap at Platform Assemble BUCKLE STRAPS together as shown above 2008 rev 6 08 Page 8 Ameristep Inc 901 Tacoma Ct P O Box 189 e Clio MI 48420 810 686 4035 www ameristep com me RAPTOR TRIPOD Model 7700 Step 10 Place HOOK END of CABLE to each BUCKLE STRAP at PLATFORM and BOTTOM LADDER SECTION looping CABLE over STABILIZER BAR Make sure CABLE PLASTIC SLIDE makes contact with STABILIZER BAR BEFORE raising Stabilizer up so it is horizontal to ground ALSO make sure there is ample tension in CABLE by tightening truss straps Be sure truss system is tight Shown below Cable Plastic Slide Step 11 Attach S HOOK BRACE STRAPS 1 to each Leg There is a sticker marking placement for each S HOOK BRACE STRAP on each Leg If sticker is not present make sure straps are on a level horizontal plane with STABILIZER BAR Once BUCKLE STRAPS are wrapped around each leg and positioned properly attach hooks on ends of each S HOOK BRACE STRAP to holes on STABILIZER BAR fig 11a Make sure legs are pushed out so as to create tension on straps 2008 rev 6 08 Page 9 Ameristep Inc 901 Tacoma Ct P O Box 189 e Clio MI 48420 810 686 4035 www ameristep com me RAPTOR TRIPOD Model 7700 Do not use in hazardous weather conditions such as lightning high winds and freezing rain
9. Leg and Ladder sections as shown and strap together with SLING STRAP and place GROUND STAKES in pocket on SLING STRAP Raptor Tripod Shown Packed BUCKLE STRAP INSTRUCTION TAG END a Se ere o See SECH SE 2 Push PRESS button to allow rough hole in underside o i t d of STRAP to be fed th h agend ofS tO Be ten throug 3 Pull tag end to adjust strap length i der PRESS BUTTON out opening uncer UTTON ou STRAP will only loosen when Press through front 2008 rev 6 08 button is pushed again Page 11 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com Ameristep Inc LIMITED WARRANTY READ THIS AGREEMENT This Ameristep product has a limited warranty No other warranties whether expressed or implied including warranties of merchantability and fitness for a particular purpose apply to the product I GENERAL PROVISIONS OF LIMITED WARRANTY A The original purchaser of this Ameristep product is warranted against defects in material and workmanship for one year following the date of its retail purchase B The exclusive remedy for defects in material and workmanship under the warranty is replacement replacement parts C Ameristep will at its option replace products not conforming to this limited warranty This is the sole and exclusive remedy available under legal theory for this Ameristep product Il NO OTHER WARRANTIES NO OTHER WARRANTIES OR REPRESENTATIONS WHETH
10. ason Practice at ground level prior to using at elevated positions Maintain the WARNINGS amp INSTRUCTIONS for later review as needed for instructions on usage to anyone borrowing your stand Use all safety devices provided with this product Never exceed weight limit specified by Manufacturer If you have any questions after reviewing the WARNINGS amp INSTRUCTIONS please contact Ameristep DO NOT lend this product to anyone unless they have read this manual and fully understand the Instructions and warnings provided e ALWAYS inspect for any damaged or missing pieces after removing all contents from box and cardboard from products If you think parts are missing or damaged contact Ameristep s Customer Service Department Do Not begin to assemble if any parts are missing or damaged e DO NOT modify or alter your Tree Ladder Stand Improper installation or adjustment may cause serious injury or death You must only use Ameristep certified replacement parts Using any other replacement parts will void product warranty DO NOT use homemade or permanently elevated stands or make modifications to a purchased TREE LADDER STAND e DO NOT use this product under the influence of alcohol medication prescription or non prescription or any illegal substance Using this product while under influence of any of these substances may result in serious injury or death e DO NOT use this product if you have a history of heart problems back problems high bl
11. h as retightening or replacement of parts preserving or refinishing wood touch up painting and lubrication is recommended e DO NOT leave your Tree Ladder Stand outside OR in a tree for more than two weeks at a time Store inside when not in use A CAUTION Maximum Tested Weight Capacity Limit for this Product is 300 POUNDS Including Accessories Gear and Attire DO NOT Exceed tested weight limit capacity This product is designed for only ONE PERSON Never remove any safety warning stickers from this product Safety must be your first priority during the use of this product ____AWARNINGA dues on lee grat vewl luste nax 2008 rev 6 08 Page 3 Ameristep Inc 901 Tacoma Ct P O Box 189 e Clio MI 48420 810 686 4035 www ameristep com HARDWARE AND PARTS me RAPTOR TRIPOD Model 7700 lt gt E 1 Shooting Rail Vee EE Bes Connection EZ Ee EE 1 Top Ladder Section SSeS rn KR 1 Left Platform 1 Right Platfor Ld ff se a 1 Middle Ladder Section 1 Footrest d 1 Bottom Ladder Section 2 Bottom Leg CREET AEL A SO 2 Middle Leg eee ee E 1 Back Rest 2 Top Leg 1 M8 x 30mm HEX BOLT 2 Washers 1 Lock Nut 1 Stabilizer Bar ae FO 3 Parts BackPack Straps 2 M8 x 40mm HEX BOLT 1 Seat Frame Base 3 Washers 1 Lock Nut d D sA AE eu 1 5 Swivel Washer 1 Shooting Rest Pad 1 Sling 2 M8 x 45mm HEX
12. ion device on your person and easily accessible Immediate access to another person may save your life In the event of an accident a rescue plan must be in place and able to be incorporated immediately ALWAYS carry emergency signal devices such as a cell phone walkie talkie whistle signal flare PLD personal locator device and flashlight on your person at all times and within reach In the event of an accident remain calm and seek help immediately DON T PANIC e NEVER adjust your stand while in use Always ensure that you and your ladder stand are safely secured to a healthy tree A checklist for selecting a safe tree is also included in the instructions Your TREE LADDER STAND must be attached tightly to the tree and secured in place ALL contact points must be in contact with tree BEFORE you step onto your TREE LADDER STAND If the stand is not secure it may shift while in use and may result in serious injury e NEVER jump on the platform OR stand on the seat OR lean out from the ladder stand for any reason e NEVER use this product for trimming trees OR as a house hold ladder e NEVER leave stand unattended Always fully inspect this product before each use DO NOT use if any bolts or nuts are loose bent or crooked e NEVER let children play or use this product without adult supervision This product is not a toy e NEVER use during inclement weather DO NOT use during thunderstorms or any other weather conditions that include but
13. not limited to lightning high wind freezing rain Your product must always be free from moisture mud frost snow ice or any other slippery surface that may compromise your safety and could potentially create dangerous conditions ALWAYS watch for changing weather conditions 2008 rev 6 08 Page 2 Ameristep Inc 901 Tacoma Ct P O Box 189 Clio MI 48420 810 686 4035 www ameristep com TREE LADDER STAND SAFETY INSTRUCTIONS WARNINGS Ameristep Tree Ladder Stands are designed with your safety being our primary concern We have invested time to properly design engineer manufacture and test this product s safety This Tree Ladder Stand will continuously be safe with appropriate equipment usage and maintenance followed carefully in this safety and instruction booklet Ameristep and Ameristep Retailers will not be responsible for any misuse of this product e ALWAYS inspect tripod before each use and do not store outdoors when not in use e ALWAYS check legs and ladder section connections every time you use tripod e ALWAYS check ground under tripod to ensure it is firm and level e ALWAYS maintain three points of contact when climbing ladder and ALWAYS lean forward as you climb PROPER CARE AND MAINTENANCE e ALWAYS inspect for defects from damage rot corrosion cracks caused from freezing or excessive heat e DO NOT use is damage is detected or suspected e ALWAYS insure the appropriate maintenance suc
14. ood pressure impaired vision equilibrium impairments dizzy if you are not physically fit or ill in any way If have been advised by a doctor or other healthcare provider not to climb or have any condition that would impair your ability to use climber Physical ailments can reduce your ability to safely install utilize and remove your product Please consult a physician prior to use Be sure you are well rested and alert and NEVER fall asleep in your stand as you may fall out resulting in serious injury or death e NEVER ttransport any equipment with yourself while ascending or descending the tripod Use a haul line such as our Hoist Rope to transport your weapons and equipment into or out of the tripod Guns should be unloaded chamber opened safety lock engaged and muzzle pointed toward the ground Only begin raising or lowering weapons and equipment while you are safely seated atop tripod with both hands free e ALWAYS know your physical limitations Falls can occur anytime after leaving the ground Don t take chances If you start thinking about how high you are don t go any higher Instead choose a minimum height that will allow for safe effective and comfortable hunting e ALWAYS have a minimum of three people present when installing or removing this product AND hunt with a plan and a buddy Before you leave home let others know your exact hunting location when you plan to return amp who is with you e ALWAYS have a communicat
15. stances or legal theory be liable or responsible for direct indirect special incidental or consequential damages B Ameristep shall not under any circumstances or legal theory be liable or responsible for any amount in excess of the product purchase price C Ameristep shall not under any circumstances or legal theory be liable or responsible for damage to items or equipment used with the Ameristep product D Ameristep shall not under any circumstances or legal theory be liable for personal injury personal loss lost profits lost wages goodwill downtime economic loss in excess of the product purchase price or any non economic damages VI ADDITIONAL PROVISIONS A This agreement is the entire agreement between you and Ameristep This agreement supercedes any prior or different agreements representations or proposals whether written or oral B No representative agent or employee of Ameristep is authorized to make warranties representations or obligations other than those set forth in this limited warranty C This agreement may only be changed through an express written agreement with Ameristep D Waiver by any party of any default or breach of this agreement will not constitute a waiver of any subsequent default or breach of the same or different kind E If any action or provision of this agreement is found to be invalid such invalidity does not affect or extend to other sections or provisions in the agreement
Download Pdf Manuals
Related Search