American Standard TownSquare Pressure Balancing Bath and Shower 2555.652 User's Manual
Contents
1. ROUGHING IN CAUTION Turn off water at main supply When soldering remove PLASTER GUARD CARTRIDGES and CHECK STOPS IF PRESENT When finished soldering flush valve body replace cartridges check stops if present and plaster guard to continue installation Use thread sealant or Teflon tape on threaded connections If the valve is installed on a fiberglass See Roughing in diagram before starting or other thin wall application the Connections are PEASTERSUARD 4 can be used as a support 1 2 female NPT for threaded inlets m Cut a 4 dia hole in the shower stall a Drill two additional 1 holes to all Connect RISER PIPE 1 to MANIFOLD 2 a oes i a EE rg ete top outlet marked SHR m Remove PLASTER GUARD 4 rotate 90 Connect TUB FILLER PIPE 3 at bottom so that indicated screw holes fit MANIFOLD 2 outlet marked TUB Push CAP on valve place ESCUTCHEON on and For proper positioning the finished wall attach with screws must be within side wall of PLASTER Connect hot and cold water supplies GUARD 4 Cap off shower pipe 5 and tub filler pipe 6 For support use pipe BRACES 7 secured to wooden braces With valve turned off turn on water supplies Check for leaks INSTALL DIVERTER When finished tiling the wall remove PLASTER GUARD 1 Remove two screws that secure the DIVERTER LID 2 and remove Lid Inspect the inside surface of diverter port Diverter port must be free of any dirt Clean if nec2. UNIT 5 Remove CAPS 7 and clean valve thoroughly Examine balancing unit and check condition of O ring on end of piston Piston should move back and forth Order Repair Part M952100 0070A if balancing unit is defective Replace CAPS 7 and install PRESSURE BALANCE UNIT 5 Make sure inlets line up with two holes in bottom of casting Top flange should butt up against top of casting BACK TO BACK INSTALLATION Remove PRESSURE BALANCE UNIT 5 Rotate PRESSURE BALANCE UNIT 5 180 so that the inlets face up and the large outlet port faces down Push PRESSURE BALANCE UNIT 5 in casting make sure inlets line up with holes in bottom of casting Top flange should butt up against top of casting Reassemble FIXATION RING 4 and CARTRIDGE 1 ROTATE B0 a LARGE OUTLET N ON Eak INLETS PSS 0 Kc Cg BACK TO BACK INSTALLATION EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968791 Rev 1 1
3. ANDLE is adjust the setting on the HOT LIMIT SAFETY STOP 1 Screw DINED TER SNDE T7 onbo DUCE ster Turn CARTRIDGE STEM 2 to the OFF position coldest setting before making adjustment to HOT LIMIT STOP 1 Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP 1 Pull forward and rotate counterclockwise one number to limit hot water temperature Use ARROW 3 on CARTRIDGE 4 and NUMBERS 5 on HOT LIMIT STOP 1 for indication Smaller Numbers 0 1397 9111315 f OM COLDER Larger Numbers 01357 91113 15 Pull INDEX CAP unscrew HANDLE SCREW and pull HANDLE off valve stem Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON Remove COVER by pulling straight out Shut off water supply by either closing off main water supply or closing off the hot and cold CHECK STOPS on valve if present VALVE LEAKS WHEN SHUT OFF Remove CARTRIDGE 1 by removing CARTRIDGE SCREWS 2 Remove three SCREWS 3 from FIXATION RING 4 and pull out PRESSURE BALANCING 5 unit Clean SEALS 9 on base of CARTRIDGE 1 Check base of PRESSURE BALANCING UNIT 5 and clean O RINGS 6 Remove CAPS 7 and check O RINGS on inside of CAPS 7 Clean inside sealing surfaces of VALVE BODY 8 Re assemble PRESSURE BALANCING UNIT 5 and CARTRIDGE 1 Tighten all screws Turn on water supply and see above for installing TRIM and HANDLE UNABLE TO MAINTAIN CONSTANT TEMPERATURE Remove PRESSURE BALANCE
4. Installation Instructions TOWNSQUARE 9555 652 PRESSURE BALANCING BATH AND SHOWER with Built in Diverter for RIM MOUNT TUB FILLER with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes Certified to comply with ANSI A112 18 1 M968791 Rev 1 1 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin ROUGHING IN DIMENSIONS E To assure proper positioning in relation to wall note Required Tools roughing in dimensions 1 5 8 TO 3 1 4 3 FINISHED WALL gt Phillips Screwdriver 1 2 PS F e OPTIONAL TO Flat Blade Screwdriver FINISHED FLOOR USUALLY BETWEEN 7 65 AND 78 OUTLETS 1 2 NPT FOR IEAD CLEARANCE SEE ILLUSTRATION 42 to 54 OPTIONAL j Channel Locks THREADED INLETS STOPS 1 SPOUT MTG g gt ye J arae ON 1 174 Adjustable Wrench A BOTTOM OF tt lt 1 2 NPT TUB 4 2 NPE 47
5. essary Install DIVERTER 3 with SCREWS 4 removed with DIVERTER LID 2 Operate DIVERTER 3 DIVERTER 3 should slide in and out smoothly Ww QR s Push on DIVERTER COVER 5 INSTALL TRIM Push CAP 1 over VALVE CARTRIDGE 2 Mount ESCUTCHEON 3 and gasket to valve body with SCREWS 4 Remove PIPE CAPS 5 from shower pipe and tub filler pipe Install SHOWER ARM 6 and SHOWER HEAD 7 CAUTION Protect finish on SHOWER ARM SHOWER HEAD and TUB SPOUT when installing INSTALL SPOUT Insert SPOUT SHANK 8 through hole of MOUNTING LEDGE Make sure that the RUBBER RING 9 is properly seated in RECESS at base of SPOUT 10 Assemble RUBBER WASHER 11 and BRASS WASHER 12 onto SHANK 8 From underside of ledge secure SPOUT 10 into position with LOCKNUT 13 Make pipe connections between valve body and SPOUT SHANK 8 RECESS BATHING POOL OR MOUNTING LEDGE DIVERTER S7 P 1 2 NPT M968791 Rev 1 1 INSTALL HANDLE AND DIVERTER KNOB 5 ADJUST HOT LIMIT STOP Install HANDLE BUSHING 1 onto CAP 2 m By restricting HANDLE rotation and limiting the amount of hot Find correct position of HANDLE 3 and push water allowed to mix with the cold the HOT LIMIT SAFETY HANDLE 3 onto VALVE STEM 4 STOP 1 reduces risk of accidental scalding To set the maximum Install HANDLE SCREW 5 and push in INDEX CAP 6 hot water temperature of your faucet all you need to do Check proper operation of H
Download Pdf Manuals
Related Search