American Standard SYMPHONY 4501 User's Manual
Contents
1. in the shower stall Connect RISER PIPE 1 to MANIFOLD 2 a Drill two additional 1 holes to allow access top outlet marked SHR to the stops m Remove PLASTER GUARD 4 rotate 90 Connect TAB Len Pre Bret poem so that indicated screw holes fit MANIFOLD 2 outlet marked TUB Push CAP on valve place ESCUTCHEON on and For proper positioning the finished wall attach with screws must be within side wall of PLASTER Connect hat and cold water supplies Cap off shower pipe 5 and tub filler pipe 6 GUARD 4 For support use pipe BRACES 7 secured to wooden braces With valve turned off turn on water supplies Check for leaks INSTALL TRIM When finished tiling the wall remove PLASTER GUARD 3 Push on CAP 1 Mount ESCUTCHEON 2 and with SCREWS 7 Install HANDLE 8 by pushing it onto CARTRIDGE STEM 9 and tightening SET SCREW 10 from below with 2 5mm Hex Wrench supplied Insert INDEX BUTTON 11 Remove cap from tub supply and plug from shower pipe Install SHOWER ARM with FLANGE 4 and SHOWER HEAD 5 Install DIVERTER SPOUT 6 ADJUST HOT LIMIT STOP HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP A ADJUSTMENT WHEN WATER I2. Installation Instructions SYMPHONY 4501 PRESSURE BALANCING BATH AND SHOWER TRIM KITS 4501S Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1 M968805 REV 1 4 ROUGHING IN DIMENSIONS m To assure proper positioning in relation to wall note roughing in dimensions rl 1 5 8 TO 3 1 4 FINISHED WALL 1 2 NPT OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65 AND 80 3 5 8 REF t INLETS 3 3 8 5 1 2 REF SHR 1 2 NPT SEE ILLUSTRATION 74 FOR HEAD INLETS 1 2 NPT CLEARANCE i iai TUB PORT 1 2 NPT THREADED INLETS 18 OPTIONAL on 1 2 NPT 5 1 8 REF 4 TOP OF TUB RIM BOTTOM OF TUB V ROUGHING IN e7 0g 0 fee Turn off water at main supply When soldering remove PLASTER GUARD CARTRIDGES and CHECK STOPS IF PRESENT When finished soldering 5 flush valve body replace cartridges check stops if present and plaster guard to continue installation Use thread Ey sealant or Teflon tape on threaded connections See Roughing in diagram before starting m Ifthe valve is installed on a fiberglass 4 Connections are or other thin wall application the 1 2 female NPT for threaded inlets PLASTER GUARD 4 can be used as a support a Cut a 4 dia hole
3. S TOO HOT lfm A By RED RING FORWARD AND ROTATE TEMPERATURE SETTING NUMBERS 5 COUNTER CLOCKWISE ONE CLICK B ADJUSTMENT WHEN WATER IS TOO COLD PRY RED RING FORWARD AND ROTATE CLOCKWISE B m f faucet drips operate handle several times from off to on Do not apply excessive force m Clogged CARTRIDGE 4 inlets may cause reduced flow in full on hot or cold To clean inlets first turn off water supply then m Remove HANDLE 1 CAP 2 and CARTRIDGE 4 Clean inlets and MANIFOLD 5 E Reassemble CARTRIDGE 4 alternately tightening SCREWS 3 E Replace CAP 2 and HANDLE 1 Check flow 5 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968805 REV 1 4
Download Pdf Manuals
Related Search