American Standard Single Control Kitchen Faucet with Cast Spout 3821.644 Series User's Manual
Contents
1. HOT LINE FOR HELP 060341 0070A For toll free information and answers to your questions call 1 800 442 1902 PIPE CAP Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 024220 0070A Weekdays 8 00 a m to 7 00 p m EST SUPPLY NUT Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968188E2. 11 by pulling up gently while moving SPOUT 11 side to side Check both SPOUT O RINGS 10 Replace if necessary On models with SPRAYS DIVERTER 9 can be cleaned by pulling DIVERTER 9 out of the MANIFOLD 12 Clean DIVERTER 9 and MANIFOLD 12 Push DIVERTER 9 back into MANIFOLD 12 PER ALOR E Reverse procedure to reinstall SPOUT CARTRIDGE and HANDLE Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Loosen HANDLE SCREW 1 and remove HANDLE 2 E Remove ESCUTCHEON CAP 3 unscrew the three CARTRIDGE SCREWS 5 m Clean inlets of CARTRIDGE 6 and MANIFOLD 12 E Reassemble CARTRIDGE 6 alternately tightening SCREWS 5 Replace CAP 3 and HANDLE 2 Check flow CARE INSTRUCTIONS m Remove as much surface dirt and film using clear water and soft cotton cloth as described m Use any of the following to remove tough surface To keep your new faucet looking new please follow film and build up these simple care instructions sec DO E Simply rinse the faucet clean with clear water m Mild liquid detergents m Clear ammonia free liquid glass cleaners DO nar the faucet with a soft cotton cloth m Non acidic non abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions E Non abrasive liquid polishers E Do not use any abrasive cleaners cloths or paper towels _ H Do not use any cleaning agents cont
3. Amirican Standard Installation Instructions JASMINE 3821 631 SERIES ET 3821 641 SERIE a 3821 634 SERIES SINGLE CONTROL KITCHEN 3821 644 SERIES FAUCET WITH CAST SPOUT Thank you for selecting American Standard the benchmark of fine quality for over 100 years Certified to comply with ANSI A112 18 1M To ensure that your installation proceeds smoothly please read these instructions carefully before you begin TOOLS REQUIRED T OQ aR Se a pun A A D 3 AS bn oO Y O LS Adjustable Wrench M968188E Regular Screwdriver Plumbers Putty or Caulking Tubing Cutter Channel Locks INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON 7 f5 0 Turn off hot and cold water supplies before beginning A Installation with ESCUTCHEON 1 Apply a bead of putty to bottom edge of ESCUTCHEON 1 Insert supply TUBES 3 and SHANK 4 through hole of ESCUTCHEON 1 and mounting surface Make certain the O RING 2 is properly seated in recess of SPOUT BASE Follow mounting instructions below to secure faucet to mounting surface B Installation less ESCUTCHEON 1 Remove ESCUTCHEON 1 feed FAUCET TUBES 3 and SHANK 4 through DECORATIVE FLANGE 10 Push FLANGE so the raised step fits into recess of SPOUT BASE m Push O RINGS 2 onto SPOUT SHANK Make certain the O RING 2 is properly seated in recess of DECORATIVE FLANGE 10 Insert SUPPLY TUBES 3 and SHANK 4 through mounti
4. CHEON 3 Assemble SPRAY HOLDER NUT 5 onto the shank of SPRAY HOLDER 4 from below and tighten Do not use putty For installation less spray cap off SPRAY HOSE CONNECTION with PIPE CAP 6 SPRAY HOSE CONNECTION 4 CONNECT HOSE SPRAY E Feed SPRAY HOSE 1 through SPRAY HOLDER 2 and attach COUPLING NUT 3 of HOSE 1 to HOSE ADAPTOR 4 on valve body Tighten COUPLING NUT 3 firmly M968188E TEST INSTALLED FAUCET Move HANDLE down into off position and remove AERATOR Turn on water supplies and check connections for leaks mp Operate HANDLE up and down left and right to flush water lines thoroughly For faucet with spray direct SPRAY HEAD into sink and Aad activate SPRAY Check hose connections for leaks m Move HANDLE down to off position and replace AERATOR CHECK CONNECTIONS FOR LEAKS SERVICE Reduced flow If the flow gradually reduces over a number of months the AERATOR may have collected debris To clean remove AERATOR and rinse with water and remove any debris Turn on faucet to wash any debris out of the faucet Thread AERATOR back into spout Operate faucet Spout leakage If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O RINGS and SPACER O RINGS m Loosen SET SCREW 1 Pull HANDLE 2 off valve stem E Remove CAP 3 and and RETAINER 4 Loosen CARTRIDGE SCREWS 5 and remove CARTRIDGE 6 Pull off SPACER 7 and O RINGS 8 Remove SPOUT
5. aining acids Once clean rinse faucet again with clear water to polish abrasives or harsh cleaners or soaps Regular and routine cleaning will reduce the need for thoroughly remove Cleaner or polish and and blot dry heavy cleaning and polishing If heavy cleaning is with a cotton cloth required the following procedures are recommended Failure to follow these care instructions may damage the faucet s finish M968188E Cee WARIS SINGLE CONTROL KITCHEN FAUCET WITH CAST SPOUT 52a527 0070A MODEL NUMBERS CARTRIDGE SCREWS separ SERIES i 023529 0070A 060343 0070A CARTRIDGE 3821 634 SERIES SPACER WITH O RINGS 3821 644 SERIES 060486 YYYOA SPOUT KIT 030746 0070A HANDLE SCREW KIT 066070 YYYOA 060483 YYYOA AERATOR SINGLE HOLE 060275 YYYOA MOUNTING KIT HANDLE KIT p A907468 YYYOA ESCUTCHEON CAP 060366 0070A 921877 0070A CAP RETAINER SPOUT SEAL KIT DO 060484 YYYOA ESCUTCHEON WITH SPRAY HOLE _M961773 YYYOA SPRAYHOLDER 3 HOLE T 000 042850 0070A amp DIVERTER SE GE c l 922400 YYYOA HAND SPRAY CD 912647 0070A S MOSE O RING SEAL 5 060485 YYYOA ESCUTCHEON Replace the YYY with ZA M953040 YYYOA appropriate finish code SPRAY HOLDER CHROME WHITE BONE BLACK NICKEL POLISHED BRASS M962146 0070A WHIT HEAT MOUNTING KIT SATIN SATIN BRASS CHROME BRASS
6. ng hole and seat DECORATIVE FLANGE 10 onto sink or mounting surface Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink or mounting surface Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the screws slightly each time until all are snug to ensure even pressure SINK OR MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS NOTE FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY Carefully bend COPPER SUPPLIES to meet water supply lines using the palms of the hands to avoid kinking COPPER SUPPLIES TUBES Connect HOT water supply line to left tube and COLD water supply line to right tube using appropriate connectors g Use 1 2 IPS FLEXIBLE SUPPLIES 3 or 3 8 O D BULL NOSE RISERS 4 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length FERRULE INSTALL SPRAY HOLDER On model with separate spray place the SPRAY HOLDER 1 into the appropriate mounting hole Assemble the SPRAY HOLDER WING NUT 2 onto the shank of SPRAY HOLDER 1 from below and tighten Do not use putty On model with spray through the ESCUTCHEON 3 place y SPRAY HOLDER 4 into the hole of ESCUT
Download Pdf Manuals
Related Search