American Standard Retrospect Console Table 7812.295 User's Manual
Contents
1. For chrome replace XXX with 002 when ordering For satin replace XXX with 295 when ordering CONSOLE CARE INSTRUCTIONS Rinse the product clean with clear water Dry with a soft cotton flannel cloth DO NOT Clean with soaps acid polish abrasives harsh cleaners or a cloth with coarse surface AMERICAN STANDARD ONE YEAR LIMITED WARRANTY If inspection of this American Standard plumbing product within one year after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for2. ASSEMBLY amp INSTALLATION INSTRUCTIONS RETROSPECT CONSOLE TABLE 7812 002 7812 295 Thank you for selecting our products products which have been the benchmarks of fine quality for over 100 years To help insure that the installation process will proceed smoothly please read these instructions carefully before you begin Also review the recommended tools and materials list carefully unpack and examine your new plumbing fixture 0282 008 RETROSPECT CONSOLE PEDESTAL TOP 8711 000 002 CONSOLE TABLE LEGS Chrome 8711 000 295 CONSOLE TABLE LEGS Satin Recommended Tools amp Materials O Adjustable Wrench gt ON 13 3 4 3 Holes yy 349mm i ee 1 3 8 35mm Dia em Channel Locks 203mm oe Plumbers Putty or Caulking 1 3 4 DIA STD DRAIN OUTLET Phillips Scre ll JJ 27 FINISHED 686mm WALL 8 1 8 TO i mea BOTTOM OF Measure eats 184mm l H DRAIN OUTLET l j 206mm t 3 8 10mm DIA 7 g CRD SINK ANCHOR SCREW HOLES SUPPLIES ON 13 3 4 349mm i AS REQ D CENTERS 1 1 4 O D WASTE Pipe Wrench j enfant O D j TAILPIECE Hacksaw FINISHED FLOOR T a sa Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 7 1 73075
3. of the wall Following manufacturer s instructions install faucet and drain assembly not included in sink Be certain to apply a bead of sealing putty on the underside of the drain to ensure a watertight seal between the sink and the drain Remove excess putty immediately after tightening drain Lavatory Move the assembly back toward the wall guiding the sink over the two headless hanger screws Place washers over studs and firmly hand tighten nuts onto Front Leg Hanger Screw each Grommet Washer amp Nut of Console Table Connect the trap to drain assembly hand tight to check alignment It may be necessary to cut off part of the tailpiece area B or part of the horizontal leg of the trap area C Connect hot and cold supplies lines between the fitting valve and the supply shut off valves Tighten trap joints for watertight assembly Apply a bead of caulk around the back edge of the sink where it contacts the wall Insert the rectangular glass shelf onto the shelf support Remove protective film from glass shelf 3 730757 100 REV B 8711 CONSOLE TABLE LEGS COMPONENTS LIST Note XXX represents color or trim finish options Specify when ordering PART NO PACKED QTY DESCRIPTION 738728 XXX0A 1 Towel Bar 738729 XXX0A Shelf Support 738730 0070A Glass Shelf 738744 XXX0A Front Leg Assembly 738743 XXX0A Rear Leg Assembly 738879 0070A Front Leg Grommet Kit 738739 0070A Hex Nut Kit 238
4. 7 100 REV B 2 Place a middle leg tube Item 4 over each threaded rod Identify the shelf support pins at the inner corners of the Shelf Support Item 5 Guide each threaded rod through the corners of the shelf support so that these support pins are nearer to you Run the two front leg sub assemblies Item 1 through the two front holes of the towel bar Item 2 Do the same with the two rear leg assemblies Item 3 Adjust the hex nut at the end of each rear leg such that 5 8 of thread is exposed Turn the unit upside down 3 e 5 Thread one decorative foot Item 7 onto the end of each rod until the leading end of the rod is recessed with the foot to a i depth of 1 4 Set the unit upright and thread one leveling 9 trumpet Item 8 on the top of the rear legs Note To prevent breakage put the rectangular glass shelf in place only after the sink and console legs are Place a bottom leg tube Item 5 over each threaded rod completely assembled and the sink has been bolted to such that the closed end of each is nearer to you Thread one the wall hex nut from the kit Item 6 onto each rod Lay the unit down and tighten each of the four legs firmly Maintain the Upon completion of console assembly follow installation 5 8 of exposed thread at the top end of the rear legs Once procedure below again set the unit upside d
5. any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada In Mexico American Standard Inc American Standard Customer Service Manager P O Box 6820 2480 Stanfield Rd Ideal Standard S A de C V Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Col Santa Clara Toll Free 800 387 0369 Ecatepec 55540 Edo Mexico For residents of the United States warranty www AmericanStandard ca www AmericanStandard com mx information may also be obtained by calling the following toll free number 800 442 1902 www AmericanStandard US com 4 730757 100 REV B
6. own SINK AND CONSOLE TABLE LEG INSTALLATION Note If replacing an existing sink be certain to shut C L of 2x8 off water supply before removing old sink If installing Support a in a new bathroom follow rough in diagram to locate and Bracket rough supply waste lines Provide suitable reinforcement behind finished wall for sink hanger screws For an installed sink height of 36 center the reinforcement 29 above the floor Finished Floor 2 730757 100 REV B 1 Move console table legs into approximate position near the wall 2 Place sink on console aligning the rubber grommets on the top of the front legs with the recesses in the underside of the front of the sink 3 Place a level on the shelf support and use the four independently adjustable console feet to level the assembly both side to side and front to back 4 Place the level on the sink and use the two independently RN Feet are adjustable trumpets on the tops of the rear legs to level the ae 4 ae sink SS 9 5 Move the assembly into contact with the wall 6 With a pencil mark through the center of the two mounting holes found on the back of the sink Rear Leg 7 Move the assembly well clear of the wall Adjustment Bumper 8 Drill two pilot holes at the center marks using a 1 4 bit Bore in 1 deep 9 Thread the two 5 16 headless hanger screws into the pilot holes leaving 1 7 8 thread exposed in front
Download Pdf Manuals
Related Search