American Standard One 2064.011 User's Manual
Contents
1. 4 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the stopper should be in the UP position Fig B Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A Fig A ey ae jE RS wai STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in2. the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F REMOVE CAM CAP M9688651 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode E Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G LOGO E To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary J dil to make sure it is fully inserted Fig J Y LOOP TOWARD X REAR OF SINK E Re install the Cam Cap making sure the guide teeth are facing outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked M
3. Americam Standard Installation Instructions 2064 011 ONE MONOBLOCK BIDET with EverClean Finish amp SpeedConnect Drain Congratulations on purchasing your American Standard faucet with EverClean finish and SpeedConnect drain two features found only on American Standard faucets Certified to comply with ANSI A112 18 1 EverClean Finish SpeedConnect Drain M968851 e One wipe effortlessly removes spots e Fewer parts installs in less time e Eliminates the need for cleaners and scrubbing e Never needs adjustment e Permanent surface protectant remains beautiful Guaranteed to seal properly the first time every time for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes Your new American Standard faucet is designed to work only with the SoeedConnect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required tools Screwdriver Channel Locks Adjustable Wrench Turn off hot and cold water A INSTALL FAUCET CAUTION supplies before beginning gt m Seat SEAL 1 into under side of ESCUTCHEON RING 2 m Seat ESCUTCHEON RING 2 with collar facing up into groove in faucet base M Feed FAUCET SUPPLIES 3 MOUNTING STUD 4 and DRAIN CABLE ASSEMBLY 8 through ESCUTCHEON RING 2 and the Figure A mounting hole of lavatory or mounting surfa
4. ce Figure A E From below push GASKET 7 and RETAINING WASHER 5 onto MOUNTING STUD 4 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink so SUPPLIES 3 rests against mounting hole Before final tightening make sure collar on MOUNTING NUT 6 is seated into RETAINING WASHER 5 Figure B GROOVE E Adjust Faucet so that it is centered Tighten MOUNTING NUT 6 TAGE to complete faucet mounting Ny a Va MOUNTING AC SURFACE COLLAR ON 4 MOUNTING NUT Figure B 2 POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A mM Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of BIDET D Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up i Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the BIDET Install FOAM GASKET 3 and FLANGE 4 onto drain body from above BIDET and tighten FLANGE 4 firmly FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET 3 is fully
5. compressed and not visible Fig A POP UP KNOB 1 must be fully down Fig B NOT VISIBLE M968851 7 ATTACH CABLE CONNECTOR mM Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is E FBC now complete Fig B gt Note Tailpeice on pop up drain is 1 1 4 O D lee Fig B 1 1 4 O D 8 CHECK OPERATION OF POP UP E Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS mM Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left SUPPLY 1 to Hot Marked with a Red Band and right supply to COLD 2 wall supply m Faucet supplies are 20 long from faucet base Note If additional supply length ts required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are to long loop as illustrated to avoid kinking m Connect 1 1 4 O D tailpiece on POP UP DRAIN to APPROX 20 waste outlet BAND 3 8 COMPRESSION M968851 4q O TEST INSTALLED FITTING m With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks E E Remove AERATOR 3 E Operate HANDLE 1 to flush water lines thorough
6. ly m Replace AERATOR 8 CHECK DRAIN CONNECTIONS E Operate POP UP KNOB 4 and fill Bidet with water Check that DRAIN STOPPER 5 makes a good seal and retains water in Bidet If DRAIN STOPPER 5 does not seal properly please refer to Troubleshooting section in these instructions E Release POP UP KNOB 4 down and check all drain connections and P trap for leaks Tighten if necessary WASTE OUTLET p TRAP i i T Turn off hot and Id Y l 4 m lo remove or replace cartidge al ls Turn valve to OFF position 3 Pull out PLUG BUTTON 1 and remove HANDLE SCREW 2 9 4 Pull off HANDLE 3 and CAP 4 a Unthread CARTRIDGE NUT 5 and remove REMOVE INSTALL a Pull out CARTEIDGE 6 ec m Inspect CARTRIDGE 6 and O RINGS 7 for debris and clean 5 if necessary Clean MANIFOLD 8 and rinse clean Reinstall CARTRIDGE 6 and O RINGS 7 onto MANIFLOD 8 Reinstall CARTRIDGE NUT 5 CAP 4 and HANDLE ASSEMBLY 3 E f spout drips operate handle several times from OFF to ON and HOT to COLD position Do not force handles turn only 90 A 2 EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface j968851
7. ode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H m To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J LOOP TOWARD FRONT OF SINK m HRe install the Gam Cap making sure the guide teeth are facing outward If the Cam Cap does not snap into place then rotate the Cam to make sure tt Is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968851
Download Pdf Manuals
Related Search