American Standard MONTERREY 5502 User's Manual
Contents
1. 6 Feed DRAIN BODY 5 up through SINK and thread FLANGE 6 fully onto BODY 5 Tighten LOCKNUT 2 firmly keeping the PIVOT ROD 7 pointed towards the back of the SINK Drop STOPPER 8 into DRAIN BODY 5 Pull TAILPIECE 1 up and thread tightly into DRAIN BODY 5 Position EXTENSION ROD 9 onto POP UP ROD 10 and tighten THUMBSCREW 11 TEST INSTALLED FAUCET Remove AERATOR With handle in OFF position turn on water supplies and check all connections for leaks 90 STOP BGs WASHER SPRING To change direction of handle rotation proceed as follows CLIP m Turn valve to OFF position mE Remove HANDLE and BONNET NUT m Remove SPRING CLIP m Lift STOP WASHER turn 90 and replace m Replace SPRING CLIP m Replace BONNET NUT HANDLE SCREW and INDEX AERATOR may accumulate dirt causing distorted and reduced water flow Remove AERATOR and rinse clean SERVICE Remove one end of CLIP 12 from PIVOT ROD 7 by squeezing ends together while sliding Insert PIVOT ROD 7 into second or third hole in EXTENSION 9 and reassemble CLIP 12 EXTENSION may need to be bent Adjust STOPPER 8 height by repositioning EXTENSION and tightening THUMBSCREW 12 Operate both handles to flush water lines thoroughly Check spout mounting and hose connections for leaks Operate LIFT ROD and check DRAIN for leaks Turn handles into OFF position and replace AERATOR If spout drips operate handles2. your questions call 4 1 800 442 1902 070532 0070A ae Weekdays 8 00 a m to 6 00 p m EST TAILPIECE oy IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1200 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008 Printed in Mexico Turn off water at main supply Apply a bead of PUTTY along the edge of the underside of the body Insert FAUCET SHANKS 5 through holes in sink Assemble RUBBER 1 and BRASS WASHERS 2 and LOCKNUTS 3 from underside of SINK Drop UPPER LIFT ROD 4 through hole in BODY models 5501 only align BODY as far forward as possible and secure position by tightening LOCKNUTS 3 Connect the HOT water supply to the left SHANK and the COLD water supply to the right SHANK using sealant appropriate connectors and COUPLING NUTS GRID DRAIN ASSEMBLY Model 5502 only Apply a bead of PUTTY around underside of DRAIN PLUG FLANGE 1 Insert DRAIN PLUG 2 into SINK drain hole Hold DRAIN PLUG 2 to prevent turning and assemble GASKET 3 WASHER 4 and LOCKNUT 5 from underneath sink Insert threaded end of TAILPIECE 6 into lower end of DRAIN PLUG 2 Connect other end to trap INSTALL POP UP DRAIN Model 7501 only Push TAILPIECE 1 down into TRAP threaded end up Thread LOCKNUT 2 WASHER 3 and GASKET 4 onto DRAIN BODY 5 Apply a bead of PUTTY to underside of FLANGE
3. Installation Instructions 5500 MONTERREY 5501 4 CENTERSET a308 LAVATORY FAUCETS Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1M US PATENT D375785 60184 Rev 1 4 051322 0020A GRID DRAIN VANDAL PROOF SCREW 051217 0020A _ 000690 0020A WRIST BLADE HANDLE KIT HANDLE SCREW 051211 0070A INDEX KIT 051210 0020A LEVER HANDLE 015025 YYYOA TNS DRAIN COMPLETE 000690 0020A HANDLE SCREW ED 051211 0070A UH M918014 0070A INDEX KIT PAIR ADAPTER M GOO a CS 070532 0040A Y 904939 0020A TAILPIECE M918014 0070A BONNET NUT O ADAPTER 028617 0020A P z POP UP ROD 066497 0020A M922286 0020A ax JY 951764 0070A COMPLETE DRAIN BODY VP AERATOR A y S CARTRIDGE 0 35gpm 1 3L min M922881 0020A Z AERATOR 066116 YYYOA 4 5gpm 5 7L min DRAIN STOPPER 066508 0020A VP AERATOR 0 5gpm 1 9L min POP UP DRAIN z S 072574 0070A 066117 YYYOA 030255 0070A FLANGE KIT EA ERSUN BOD MOUNTING KIT 2O00 4K l XN 970847 0070A CLIP 024220 0070A N COUPLING NUT 066118 0070A PIVOT ROD O RING 900864 0070A DRAIN BODY TAILPIECE INSERT HOT LINE FOR HELP Zon For toll free information and answers to
4. several times from OFF to ON position Do not force handles turn only 90 Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow To clean first turn off hot and cold water supplies then m Remove HANDLE and BONNET NUT m Remove CARTRIDGE by pulling up m thee rinse plastic SCR at base of CARTRIDGE Replace CARTRIDGE until flange is tight against valve body Turn valves OFF Replace BONNET NUT HANDLE SCREW and INDEX CARTRIDGE SCREEN 60184 Rev 1 4
Download Pdf Manuals
Related Search