American Standard Lakeland 4114.001 User's Manual
Contents
1. 3 Assemble SPRAY HOLDER NUT 5 onto the shank of SPRAY HOLDER 4 from below and hand tighten Do not use putty For installation less spray cap off SPRAY HOSE ae em 9 CONNECTION 9 with PIPE CAP 6 CONNECT HOSE SPRAY Feed SPRAY HOSE 7 through SPRAY HOLDER 1 and attach COUPLING NUT 8 4 of HOSE 7 to SPRAY HOSE CONNECTION 9 on valve body Tighten COUPLING NUT 8 firmly TEST INSTALLED FAUCET Move HANDLE down into off position and remove AERATOR 1 Turn on water supplies and check connections for leaks m Operate HANDLE 2 up and down left and right to flush water lines thoroughly For faucet with spray direct SPRAY HEAD 3 into sink and activate SPRAY 3 Check hose connections for leaks m Move HANDLE 2 down to off position and replace AERATOR 1 CHECK CONNECTIONS FOR LEAKS M968469 REV 1 1 SERVICE Reduced flow If the flow gradually reduces over a number of months the AERATOR 12 may have collected debris To clean remove AERATOR 12 and rinse with water and remove any debris Turn on faucet to wash any debris out of the faucet Thread AERATOR 12 back into spout Operate faucet m Spout leakage If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O RINGS First turn off water supply m Remove HANDLE BUTTON 2 and loosen SET SCREW 1 with 2 5mm HEX WRENCH 11 supplied Pull HANDLE 3 off valve stem E Pull off CAP 4 Loosen CART2. Americam Standard Installation LAKELAND Instructions SINGLE CONTROL KITCHEN 4114 001 FAUCET WITH CAST SPOUT 4114 003 with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots ai e Eliminates the need for cleaners and scrubbing RRO PARE wehcy rary sone e Permanent surface protectant remains beautiful for the life of the faucet M968469 REV 1 1 e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin TOOLS REQUIRED Regular Screwdriver Phillips Screwdriver Adjustable Wrench Plumbers Putty or Caulking 1 INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON CAUTION Turn off hot and cold water supplies before beginning A Installation with ESCUTCHEON 1 Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE 1 Insert supply HOSES 2 and SHANK 3 through hole of ESCUTCHEON with PUTTY PLATE 1 and mounting surface Follow mounting instructions below to secure faucet to mounting surface B Installation less ESCUTCHEON 1 Discard ESCUTCHEON with PUTTY PLATE 1 Insert supply HOSES 2 and SHANK 3 through mounting hole
3. RIDGE SCREWS 5 and remove CARTRIDGE 6 m Remove SPOUT 7 by pulling up gently while moving SPOUT 7 side to side E Check both SPOUT O RINGS 8 for damage Replace if necessary On models with SPRAYS DIVERTER 9 can be cleaned by pulling DIVERTER 9 out of the MANIFOLD 10 Rinse clean the DIVERTER 9 and MANIFOLD 10 Push DIVERTER 9 back into MANIFOLD 10 E Reverse procedure to reinstall SPOUT CARTRIDGE and HANDLE Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Remove PLUG BUTTON 2 loosen HANDLE SCREW 1 and remove HANDLE 3 Remove ESCUTCHEON CAP 4 Unscrew the three CARTRIDGE SCREWS 5 Clean MANIFOLD 10 CARTRIDGE 6 ports and SEALS 13 Clean inlets of CARTRIDGE 6 and MANIFOLD 10 Reassemble CARTRIDGE 6 alternately tightening SCREWS 5 Replace CAP 4 and HANDLE 3 Check flow EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968469 REV 1 1
4. and seat SPOUT BASE onto sink or mounting surface Do not use putty Assemble RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 onto SHANK 3 from underside of sink or mounting surface Hand tighten LOCKNUT 6 and check that rotation of HANDLE 7 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 8 on LOCKNUT 6 Work your way around LOCKNUT 6 tightening the screws slightly each time until all are snug to ensure even pressure SPOUT BASE SINK TE MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot Marked with a Red Line and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 21 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking INSTALL SPRAY HOLDER On model with separate spray place the SPRAY HOLDER 1 into the appropriate mounting hole Assemble the SPRAY HOLDER WING NUT 2 onto the shank of SPRAY HOLDER 1 from below and hand tighten Do not use putty On model with spray through the ESCUTCHEON 3 place SPRAY HOLDER 4 into the hole of ESCUTCHEON
Download Pdf Manuals
Related Search