American Standard Jasmine Amarilis 3808.101 User's Manual
Contents
1. over STUD 9 and secure with NUT 10 Before final tightening adjust faucet so that it is centered over mounting hole SINGLE HOLE INSTALLATION 2 POP UP DRAIN E Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 m Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B REMOVE FLANGE Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of SINK E Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A i 7 WHITE FOAM POP UP KNOB 1 must be fully down Fig B GASKET DRAIN NOT VISIBLE FLANGE NS i Rar 51314 Rev 1 3 7 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Ta2. Amirican Standard Installation Instructions JASMINE Oe AMARIS 3808 101 Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Certified to comply with ANSI A112 18 1 Speed Connect Drain 51314 Rev 1 3 e Fewer parts installs in less time e Never needs adjustment Guaranteed to seal properly the first time every time To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools Faj A Screwdriver Channel Locks Adjustable Wrench INSTALL FAUCET main supply For single hole installation Fig A Make sure that O RING 1 is installed into base of FAUCET 2 E OUTCHEON PLANE For installation with DECORATIVE RING 3 single hole installation feed faucet SUPPLIES 4 and CABLE CONNECTOR 5 through sink or mounting surface hole For installation with ESCUTCHEON PLATE 6 for 3 hole 4 centers installation use the following steps Fig B Unscrew and remove DECORATIVE RING 3 from FAUCET BODY 2 Apply putty to underside of ESCUTCHEON PLATE 6 and place over mounting holes E Feed faucet tubes through O RING 1 supplied with ESCUTCHEON PLATE 6 and through the hole in the ESCUTCHEON 6 and through SINK or DECK From below push GASKET 7 and RETAINER PLATE 8
3. FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE 51314 Rev 1 3
4. eaks m Tighten if necessary SERVICE IF FAUCET DRIPS If faucet drips operate handle several times from off to on Do not apply excessive force Clogged CARTRIDGE 5 inlets may cause reduced flow in full on hot or cold To clean inlets first turn off water supply then E Remove HANDLE 1 CAP 2 CARTRIDGE SCREWS 3 RETAINER 4 and CARTRIDGE 5 E Clean inlets on CARTRIDGE 5 E Reassemble CARTRIDGE 5 RETAINER 4 alternately tightening SCREWS 3 CAP 2 and HANDLE 1 Check flow 1 2 CARE INSTRUCTIONS WASTE OUTLET HOT LIMIT SAFETY STOP By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP Remove necessary trim parts Use a flat blade screwdriver or pull forward with your fingers to rotate red HOT LIMIT SAFETY STOP Follow Step A or B to adjust max min discharge temperature O being the hottest to 7 the coldest temperature setting a ADJUSTMENT WHEN WATER IS TOO HOT lt A POINTI PRY RED RING FORWARD INTER ON HOT LIMIT STOP B ADJUSTMENT WHEN WATER IS TOO COLD B PRY RED RING FORWARD AND ROTATE CLOCKWISE RED RING HOT LIMIT SAFETY STOP DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON
5. ilpeice on pop up drain is 1 1 4 O D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left SUPPLY 1 to Hot Marked with a Red Band and right supply to COLD 2 wall supply Faucet supplies are 20 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are to long loop as illustrated to avoid kinking Connect 1 1 4 O D tailpiece on POP UP DRAIN to F waste outlet Ox 20 BLUE BAND 3 8 COMPRESSION 51314 Rev 1 3 TEST INSTALLED FITTING With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks m Remove AERATOR 3 Operate HANDLE 1 to flush water lines thoroughly Replace AERATOR 3 CHECK DRAIN CONNECTIONS Operate POP UP KNOB 4 and fill lavatory with water Check that DRAIN STOPPER 5 makes a good seal and retains water in SINK If DRAIN STOPPER 5 does not seal properly please refer to Troubleshooting section in these instructions Release POP UP KNOB 4 down and check all drain connections and P trap for l
Download Pdf Manuals
Related Search