American Standard Jasmine 3821.6XX User's Manual
Contents
1. For installation less spray cap off SPRAY HOSE CONNECTION with PIPE CAP 6 CONNECT HOSE SPRAY Feed SPRAY HOSE 1 through SPRAY HOLDER 2 and attach COUPLING NUT 3 of HOSE 1 to HOSE ADAPTOR 4 on valve body Tighten COUPLING NUT 3 firmly M968188 REV 1 1 TEST INSTALLED FAUCET Move HANDLE down into off position and remove AERATOR Turn on water supplies and check connections for leaks Operate HANDLE up and down left and right to flush water lines thoroughly AERATOR For faucet with spray direct SPRAY HEAD into sink and activate SPRAY Check hose connections for leaks Move HANDLE down to off position and replace AERATOR CHECK CONNECTIONS FOR LEAKS mm SERVICE Reduced flow If the flow gradually reduces over a number of months the AERATOR may have collected debris To clean remove AERATOR and rinse with water and remove any debris Turn on faucet to wash any debris out of the faucet Thread AERATOR back into spout Operate faucet Spout leakage If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O RINGS and SPACER O RINGS Loosen SET SCREW 4 Pull HANDLE 2 off valve stem Remove CAP 3 and and RETAINER 4 Loosen CARTRIDGE SCREWS 5 and remove CARTRIDGE 6 Pull off SPACER 7 and O RINGS 8 Remove SPOUT 11 by pulling up gently while moving SPOUT 11 side to side Check both SPOUT O RINGS 10 Replace if necessary On models with SPRAY2. Amtricam Standard Installation Instructions JASMINE 381 80 AMARILIS SINGLE CONTROL KITCHEN FAUCET AND CAST SPOUT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly Certified to comply with ANSI A112 18 1M please read these instructions carefully before you begin M968188 REV 1 1 TOOLS REQUIRED Ea Phillips Screwdriver mane 3 Channel Locks Adjustable Wrench Plumbers Putty or Caulking Regular Screwdriver INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON main supply A Installation with ESCUTCHEOWN 1 Apply a bead of putty to bottom edge of ESCUTCHEON 1 Insert supply HOSES 3 and SHANK 4 through hole of ESCUTCHEON 1 and mounting surface Make certain the O RING 2 is properly seated in recess of SPOUT BASE Follow mounting instructions below to secure faucet to mounting surface B Installation less ESCUTCHEOWN 1 Remove ESCUTCHEON 1 feed FAUCET HOSES 3 and SHANK 4 through DECORATIVE FLANGE 10 Push FLANGE 10 so the raised step fits into recess of SPOUT BASE m Push O RING 11 onto SPOUT SHANK 4 Make certain the O RING 11 is properly seated in recess of DECORATIVE FLANGE 10 m Insert SUPPLY HOSES 3 and SHANK 4 through mounting hole and seat DECORATIVE FLANGE 10 onto sink or mounting surface Assemble RUBBER WASHER 5 BRASS WA
3. DLE 3 tighten HANDLE SCREW 1 and install INDEX BUTTON 2 RED RING HOT LIMIT SAFETY STOP M968188 REV 1 1
4. S DIVERTER 9 can be cleaned by pulling DIVERTER 9 out of the MANIFOLD 12 Clean DIVERTER 9 and MANIFOLD 12 Push DIVERTER 9 back into MANIFOLD 12 A AERATOR Reverse procedure to reinstall SPOUT CARTRIDGE and HANDLE Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Loosen HANDLE SCREW 1 and remove HANDLE 2 E Remove ESCUTCHEON CAP 3 unscrew the three CARTRIDGE SCREWS 5 m Clean inlets of CARTRIDGE 6 and MANIFOLD 12 E Reassemble CARTRIDGE 6 alternately tightening SCREWS 5 Replace CAP 8 and HANDLE 2 Check flow HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental A scalding To set the maximum hot water temperature of your faucets all you PRY RED RING FORWARD need to do is adjust the setting on the HOT LIMIT SAFETY STOP CLOCKWISE ONE CLICK Remove HANDLE BUTTON 1 and loosen SET SCREW 2 Pull SETTNG NUMBERS HANDLE 3 off valve stem Pull off CAP 4 Use a flat blade alana screwdriver or your fingers to pull up and rotate red PRY RED Sid FORWARD HOT LIMIT SAFETY STOP 5 Follow Step A or B to adjust AND ROTATE CLUEKWISE min max discharge temperature O being the hottest to B B 7 the coldest temperature setting Factory set at O ADJUSTMENT WHEN WATER IS TOO COLD Replace ESCUTCHEON CAP 4 HAN
5. SHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink or mounting surface Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the screws slightly each time until all are snug to ensure even pressure SINK i MOUNTING SURFACE MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot Marked with a Red Line and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 21 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking INSTALL SPRAY HOLDER On model with separate spray place the SPRAY HOLDER 1 into the appropriate mounting hole Assemble the SPRAY HOLDER WING NUT 2 onto the shank of SPRAY HOLDER 1 from below and tighten Do not use putty On model with spray through the ESCUTCHEON 3 place SPRAY HOLDER 4 into the hole of ESCUTCHEON 3 Assemble SPRAY HOLDER NUT 5 onto the shank of SPRAY HOLDER 4 from below and tighten Do not use putty
Download Pdf Manuals
Related Search