American Standard Enfield T37373X User's Manual
Contents
1. CAP M950119 YYY420A CROSS HANDLE A918434 0070A ESCUTCHEON SCREWS M918038 0070A ADAPTER M918990 0070A SELF TAPPING SCREW Replace the YYY with appropriate finish code CHROME POLISHED NICKEL BLACKENED BRONZE SATIN NICKEL HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 12 00 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008 M968662 REV 1 12. Installation Instructions ENFIELD 137373X CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT Thank you for selecting American Standard the benchmark of fine quality for over 100 years Certified to comply with ANSI A112 18 1M To ensure that your installation proceeds smoothly please ass 1016 read these instructions carefully before you begin M968662 REV 1 1 ROUGHING IN DIMENSIONS 242mm 9 5 8 R510 3 4 NPT R510 1 2 NPT R530 3 4 NPT 48mm to 68mm 2 to 2 5 8 Recommended Tools 3 Flat Blade Screwdriver Phillips Screwdriver CARE INSTRUCTIONS Remove as much surface dirt and film using clear water and soft cotton cloth as described above E To keep your new faucet looking new please follow these simple care instructions m Use any of the following to remove tough surface l film and build up DO E Simply rinse the faucet clean with clear water m Mild liquid ae E Dry the faucet with a soft cotton cloth m Clear ammonia free liquid glass cleaners DO NOT gm Nor acidic non abrasive gentle liquid or fully dissolved powder cleansers mixed according to E Do not use any abrasive cleaners cloths or manufacturers directions paper towels PR Non abrasive liquid polishers E Do not use any cleaning agents containing acids polish abrasives or harsh cleaners or m Once clean rinse faucet again with cl
3. e right pull off KNOB MOUNT 3 and reinstall KNOB MOUNT 3 with arrow B pointing upwards SET HOT LIMIT STOP m The maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired m Remove the TEMPERATURE LIMIT STOP 4 H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 112 F For 100 F adjustment turn the water supply on Turn KNOB MOUNT 3 until the spout temperature is 100 F Check that arrow marking A on the KNOB MOUNT 3 still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE 5 Remove KNOB MOUNT 8 without turning by sliding out as indicated by the arrow Reinstall the KNOB MOUNT 38 so that the arrow marking A points upwards Reinstall RED LOCKING DEVICE 5 OPERATING THE VALVE Turn on water supply on and test installed fitting If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed See step 3 for TRANSPOSED SUPPLY PIPING Operate valve from off to cold to hot Check temperature If max mixed water temperature is to hot or to cold see step 4 and re calibrate the valve M968662 REV 1 1 ENFIELD CENTRAL THERMOSTAT LESS VOLUME CONTROL TRIM KIT MODEL NUMBERS T37373X M962629 YYY0OA ESCUTCHEON KIT M909834 YYYOA DIAL PLATE M950118 YYY420A LEVER HANDLE A907090 YYYOA
4. ear water to soaps thoroughly remove cleaner or polish and blot dry with a soft cotton cloth Regular and routine cleaning will reduce the need for heavy cleaning and polishing If heavy cleaning is i required the following procedures are recommended Failure to follow these care instructions may damage the Faucet s finish TRIM INSTALLATION Push CAP 1 over the O RING SEAL 2 Push ESCUTCHEON 3 over CAP 1 Attach ESCUTCHEON 3 to VALVE 4 with the two SCREWS 5 provided Push DIAL PLATE 6 over CAP 1 and into the four alignment holes in ESCUTCHEON 3 HANDLE INSTALLATION Install STEM ADAPTER 1 onto KNOB MOUNT 2 with ADAPTER SCREW 3 Align HANDLE 4 4a and push onto KNOB MOUNT 2 Tighten SET SCREW with HEX WRENCH 5 supplied TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible proceed as follows Shut off water supply CHECK STOP E PPY BLUE TO RED E Remove handle and rim E Remove check stops and re install them transposed Important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left CHECK STOP Turn the water supply back on and perform the temperature adjustment in step 4 RED TO BLUE TEMPERATURE CALIBRATION Check that arrow marking B points vertically upwards If not push the BLACK CLAMP 1 on the SECURING RING 2 to th
Download Pdf Manuals
Related Search