American Standard Enfield 2373.401 User's Manual
Contents
1. H FOR GROUND JOINT CONNECTION OR 1 2 Aai D SLIP INLETS MAX Jj A i FINISHED REAR VIEW WITH FLOOR nN J WALL REMOVED holes from underside of the BIDET LEDGE Drop the RUBBER RING 3 over the VALVE BODIES 2 and thread DECK ADAPTER 4 onto VALVE BODIE 2 until it locks against the internal stop Tighten the MOUNTING NUT 1 to secure the VALVE BODIES 2 Remove MOUNTING NUT 9 FRICTION RING 10 and UPPER GASKET 7 from TRANSFER VALVE 8 and insert TRANSFER VALVE 8 into the center forward hole of BIDET Replace UPPER GASKET 7 and FRICTION RING 10 Position the side threaded outlet rearward and secure MOUNTING NUT 9 Thread ESCUTCHEON 5 onto TRANSFER VALVE 8 until it seats against the BIDET LEDGE 2 DRAIN INSTALLATION 3 SPRAY INSTALLATION E Assemble SPRAY BODY 1 to BIDET Using putty seal een ape ran ee eo a underside of SPRAY BODY FLANGE 2 and secure with Concave side of cup WASHER 2 is toward NUT 3 ball Screw SPRAY HOSE 4 with SEAL WASHER 5 to SPRAY Thread LOCKNUT 6 WASHER 7 and BODY 1 Connect other end of HOSE 4 with SEAL GASKET 8 onto DRAIN BODY 5 WASHER 6 to side outlet NIPPLE 7 of the TRANSFER VALVE 8 Apply a bead ot PUTIY Ea underside m Screw SPRAY CAP 9 onto SPRAY BODY 1 of FLANGE 9 Feed DRAIN BODY 5 up through BIDET and thread FLANGE 9 fu2. Installation Instructions 2373 401 2373 421 ENFIELD BIDET FITTING and VACUUM BREAKER with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots e Eliminates the need for cleaners and scrubbing e Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Adjustable Wrench Channel Locks y L Certified to comply with ASME A112 18 1M U S Patent No 5 819 789 M968297 REV 1 1 Required Tools hye Wrench Flat Blade Screwdriver 3 Phillips Screwdriver Supplied with Fitting Roughing in Dimensions 1 MOUNTING BIDET FAUCET Turn off hot and cold water CAUTION supplies before beginning Place MOUNTING NUTS 1 onto the VALVE BODIES 2 and insert VALVE BODIES 2 through outside TRANSFER VALVE BIDET OUTLINE FOR FLUSHING IS SYMBOLIC RIM OR SPRAY DOUCHE SPRAY 7 8 DIA ADJ 1 1 4 x TO 2 1 4 1 3 8 DIA A 1 1 4 0 D TAILPIECE DIVERTER AND VACUUM BREAKER F 12 ASSEMBLY
3. PPER 4 and check all drain connections for leaks Tighten if necessary HANDLE ASSEMBLY E To change direction of handle rotation proceed as follows EEA Turn valve to OFF position Unthread HANDLE BASE 1 from DECK ADAPTER 2 avira a a Pull HANDLE ASSEMBLY off VALVE STEM 3 Bg m Remove SPRING CLIP 4 Lift STOP WASHER 5 turn 90 and replace Replace SPRING CLIP 4 a Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM 3 to female teeth in HANDLE Thread HANDLE ASSEMBLY onto DECK ADAPTER 2 until snug against mounting surface TO CLEAN SPRAY SPRAY 6 may accumulate dirt causing distorted and reduced water flow Unscrew and remove SPRAY 6 and rinse clean Replace SPRAY 6 and operate handles several times from OFF to ON position Do not force handles turn only 90 EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968297 REV 1 1
4. lly onto BODY 5 Tighten LOCKNUT 6 firmly keeping the PIVOT ROD 3 pointed towards the back of the BIDET Push DRAIN ESCUTCHEON 10 onto TAILPIECE 11 4 TEE AND HOSE CONNECTION gm Insert SEAL 1 into ADAPTER 2 and tighten ADAPTER 2 to bottom of TRANSFER VALVE 3 E Install SEAL 4 into coupling nut of TEE 5 and tighten connection to ADAPTER 2 Connect HOSE COUPLING NUTS 6 to Hot and Cold valve bodies and securely tighten 5 LIFT ROD GUIDE INSTALLATION Unscrew LIFT ROD NUT 1 from LIFT ROD GUIDE 2 Make sure SEAL 3 is seated into ESCUTCHEON of LIFT ROD GUIDE 2 Drop LIFT ROD GUIDE 2 into rear hole of bidet and from below secure with ROD GUIDE NUT 1 M968297 REV 1 1 INSTALL HANDLES DIVERTER KNOB Push ADAPTER 1 on VALVE STEM 2 so that the hole of the E Install HANDLE ADAPTER 8 onto valve stem ADAPTER 1 without a spline is facing up See figure A Tighten STEM SCREW 3 to secure ADAPTER 1 E Push DIVERTER KNOB 7 onto HANDLE ADAPTER 8 Find correct position of LEVER HANDLE ASSEMBLY 4 or CROSS E Install RING 9 onto DIVERTER KNOB 7 and tighten HANDE ASSEMBLY 5 by adjusting male teeth on ADAPTER 1 to with HANDLE SCREW 10 female teeth in HANDLE 4 5 P KNOB CAP 11 Thread LEVER HANDLE ASSEMBLY 4 or CROSS HANDE ASSEMBLY ara an 5 onto DECK ADAPTER 6 until snug against mounting surface THREAD ON TO DECK ADAPTER TOP S i Wesco Fig
5. ure A F SPLINE END DOWN NOTE FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE PURCHASED SEPARATELY Connect water supplies to FAUCET 1 with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections COUPLING NUT Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length FERRULE 8 FINISH DRAIN INSTALLATION Position BIDET fixture and secure to floor Insert lift rod into lift rod guide Position EXTENSION ROD 1 onto POP UP ROD 2 and tighten THUMBSGREW 3 Remove one end of CLIP 4 from PIVOT ROD 7 by squeezing ends together while sliding Insert PIVOT ROD 7 into second or third hole in EXTENSION ROD 1 and reassemble CLIP 4 EXTENSION ROD 1 may need to be bent Adjust STOPPER height by repositioning EXTENSION ROD 1 and tightening THUMBSCREW 3 Using metal TAILPIECE 5 make connection to the TRAP 6 M968297 REV 1 1 9 TEST INSTALLED FITTING With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks mb Operate both handles to flush water lines thoroughly Turn DIVERTER 6 to rim wash and bidet spray Operate Lift Rod 3 and fill Bidet with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Bidet Adjust stopper height by repositioning Lift Rod 3 and tightening Thumbscrew 5 Release DRAIN STO
Download Pdf Manuals
Related Search