American Standard Dazzle 6028.401 User's Manual
Contents
1. GUIDE 1 to bidet Hand tighten only Fig B M968803 Rev 1 1 SLOTTED MOUNTING N 1 0 TEE AND HOSE CONNECTION ATTACH CABLE CONNECTOR POP UP KNOB 1 must be fully down Fig A Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig B Your new POP UP DRAIN installation is now complete Fig C Note Tailpeice on pop up drain 1 1 4 O D is 1 1 4 O D Fig C CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions INSTALL DIVERTER KNOB Push DIVERTER KNOB 1 onto HANDLE ADAPTER 2 Push on RING 3 and tighten with SCREW 4 Press on KNOB CAP 5 Note Screwdriver gap is for disassembling and should point downwards Insert SEAL 1 into ADAPTER 2 and tighten ADAPTER 2 to bottom of TRANSFER VALVE 3 Install SEAL 4 into coupling nut of TEE 5 and tighten connection to ADAPTER 2 Connect HOSE COUPLING NUTS 6 to Hot and Cold valve bodies and securely tighten WATER SUPPLY CONNECTION COUPLING 7 NUT NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY a6 1 2 PIPE NOS Connect water supply to VALVE BODIES 7 7a with THREAD BULE NOTE 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to2. SEAL WASHER 5 to SPRAY BODY 1 Connect other end of HOSE 4 with SEAL WASHER 6 to side outlet NIPPLE 7 of the TRANSFER VALVE 8 Thread SPRAY CAP 9 onto SPRAY BODY 1 3 POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 4 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of BIDET E Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the BIDET Install FOAM GASKET 3 and FLANGE 4 onto drain body from above BIDET and tighten FLANGE 4 firmly FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET 1 is fully compressed and not visible Fig A POP UP ROD ASSEMBLY Insert LIFT ROD GUIDE 1 and CABLE CONNECTOR 2 through rear hole making sure SEAL WASHER 3 is UT properly seated Fig B a oam C 4 GASKET ILLUSTRATION From below slip slot in MOUNTING NUT 4 over CABLE 5 NOT VISIBLE Tae 2 Thread NUT 4 onto lift rod guide shank to secure ROD
3. We SPRAY E mm e 1 1 4 MAX AT Z N N TO 2 1 4 DIA jin i ik rh Phillips Screwdriver Channel Locks oF e T 1 3 8 IF A Bia ale 7 FOR GROUND JOINT 3 7 8 CONNECTION OR 1 72 ic iets ZS II Te O D SLIP INLETS 5 1 2 FLOORS WALL REMOVED Adjustable Wrench T Tubing Cutter M 1 174 0 D TAILPIECE J emer FAUCET INSTALLATION WUN pipaa a i baa a 49 6 m Place RUBBER RING 10 into ADAPTER 4 7 E Install LOCKNUT 1 and RUBBER WASHER 2 onto VALVE BODIES 3 3a From under side of mounting surface install VALVE BODY 3 3a through valve mounting holes Threads of VALVE BODY 3 3a should extent at least 5 16 of a inch above mounting surface top Fig A Thread ADAPTER 4 onto VALVE BODIES 3 3a until snug against internal stop If necessary adjust LOCKNUT 1 4S E Tighten LOCKNUTS 1 with WRENCH 5 supplied to secure VALVE BODIES 3 3a m Remove MOUNTING NUT 6 WASHER 7 and 5 16 UPPER GASKET 8 from TRANSFER VALVE 9 MIN Insert TRANSFER VALVE 9 into the center forward hole of BIDET 4 E Replace UPPER GASKET 8 and WASHER 7 Position the side threaded outlet rearward and secure MOUNTING NUT 6 Thread ESCUTCHEON 41 onto TRANSFER 3 3a VALVE 9 until it seats against the BIDET LEDGE SPRAY INSTALLATION Assemble SPRAY BODY 1 to BIDET Using putty seal underside of SPRAY BODY FLANGE 2 and secure with NUT 3 Thread SPRAY HOSE 4 with
4. American Standard Installation DAZZLE Instructions Bidet Faucet and Vacuum Breaker 6028 401 with EverClean Finish amp SpeedConnect Drain Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain two features found only on American Standard faucets EverClean Finish 3 e One wipe effortlessly removes spots Pee aioe a ae Eliminates the need for cleaners and scrubbing SpeedConnect Drain e Permanent surface protectant remains beautiful e Fewer parts installs in less time for the life of the faucet e Never needs adjustment e EverClean available on Polished Chrome Satin Nickel Guaranteed to seal properly the first time every time Stainless Steel Polished Brass or any combination of these finishes Your new American Standard faucet is designed to work only with the SoeedConnect drain Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Roughing in Dimensions 8 TO 12 TRANSFER VALVE FINISHED FOR FLUSHING WALL N Required tools DIVERTER AND C_D VACUUM BREAKER 8 ASSEMBLY c _ re RIM OR SPRAY Eee TE Screwdriver Plumbers Putty or IS SYMBOLIC DS 7 8 DIA 5 Caulking SCRE YD 1 3 16 DIA DOUCHE ADJ 1 1 4 2 1 8 Balas a im 4 1 4 lt
5. N STOPPER 4 makes a good seal and retains water in Bidet If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions a SPRAY ERED KISS VV i Ky AVV A E Push POP UP KNOB 3 down and check all drain connections and P trap for leaks m Tighten if necessary EverClean Finish Care Instructions American Standard s EverClean E To oe T of handle rotation a e proceed as follows eg oe wipe clean with a soft Turn valve to OFF position Unthread HANDLE Fy ee BASE 1 from DECK ADAPTER 2 A soft cloth with clean water Pull HANDLE ASSEMBLY off VALVE STEM 3 may also be used if desired Remove SPRING CLIP 4 Lift STOP WASHER 5 No additional cleaning products turn 90 and replace Replace SPRING CLIP 4 are required Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM 8 to female teeth in HANDLE Thread HANDLE ASSEMBLY onto DECK ADAPTER 2 i until snug against mounting surface polish abrasives harsh If spout drips operate handles several times from cleaners or a cloth with a OFF to ON position Do not force handles turn coarse surface only 90 DO NOT USE Soaps acid M968803 Rev 1 1 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too sl
6. Stopper can now be removed by lifting it out of the Drain Fig F CAM REMOVE CAM CAP M968803 Rev 1 1 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G E To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J m Reinstall the Cam Cap making sure the guide teeth are facing i mi pl outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K E Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H m To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward th
7. e front of the sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H E Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD m Re install the Gam Cap making sure the guide teeth are facing FRONT OF BIDET outward If the Cam Cap does not snap into place then rotate the Cam to make sure tt Is fully inserted Fig K E Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968803 Rev 1 1
8. owly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE E Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A m Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B E Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER STOPPER REMOVAL PROCEDURE m Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A E Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B mM Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D mM Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The
9. tighten connections NI gt Do not over tighten Be careful not to kink copper supply when 2 a bending Use tubing cutter to cut to proper length SIPE Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet CONNECT TO WASTE OUTLET 3 8 COMPRESSION CONNECTION M968803 Rev 1 1 INSTALL HANDLES E Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up See figure A Tighten STEM SCREW 8 to secure ADAPTER 1 Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 5 until snug against mounting surface Figure A ee pelt yy lt p SPLINE END same 1 2 TEST INSTALLED FITTING m With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks gt m Operate both HANDLES 1 to flush water lines thoroughly mM Rotate TRANSFER VALVE 5 from rim wash to spray several times to check operation lt a z KA NA PETA A P _ Spl GEES KE VVS V AY AVVV VV 1 3 CHECK DRAIN CONNECTIONS KI E Pull up POP UP KNOB 3 and fill Bidet with water Check that DRAI
Download Pdf Manuals
Related Search