American Standard Chandler Americast 7182.000 User's Manual
Contents
1. If an American Standard Americast brand product is found to be defective in materials or workmanship after inspection by an authorized American Standard representative American Standard will repair or at its option exchange the product for a similar model This warranty extends for the lifetime of the product so long as it remains in use in its original place of installation except that the warranty applies to a bathing vessel s slip resisting surface only for the first year after the product s initial installation This warranty applies only to the original purchaser and installation of these products This warranty does not apply to whirlpool components or to faucets drains mounting rims grab bars or other accessories If manufactured or supplied by American Standard such whirlpool components and accessories are covered under separate limited warranties This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation This warranty shall be void if the Americast brand product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it was modified in a manner inconsistent with the p2. MODIFICATION REQUIRED TO FIT ISLAND SINK WITH FAUCET HOLES INTO A STANDARD 15 X 15 SINK CUTOUT NOTE CHANDLER ISLAND SINK WITHOUT FAUCET HOLES DOES NOT FIT INTOA STANDARD 15 X 15 SINK CUT OUT Product names listed herein are trademarks of American Standard Inc unless otherwise noted CUTTING SINK Layo typ LINE OUTLINE ISLAND SINK MODEL 7182 000 CUTOUT FOR NEW INSTALLATION 16 1 2 419mm 15 9 16 395mm 287mm 6 23 32 171mm 4 CENTER LINE l 6 23 32 OF BOWL 71mm aos 2 CUTTING SINK i 1 2 TVP LIN E OUTLINE 15 381mm 3 4 19mm T 14 356mm 14 356mm 6 23 32 z ius T 171mm A aa a CENTER LINE 4 gost Radius 44 112 Ra 6 23 32 1 geamm 171mm ae ti L 1 2 TYP SINK LINE OUTLINE American Standard Inc 2003 AFTER THE CUTOUT IS DRAWN Drill a clearance hole inside the cutout line as marked on the countertop Perimeter of sink Cut opening on cut line inside the peri meter of sink Mount the faucet and drain assembly on the sink following the manufacturer s instructions Before applying the sealant place the sink temporarily into the cutout Check for alignment and clear ance then trace around the outside edge of the sink as a guide for installation location and application of sealant Remove sink AMERICAST LIMITED LIFETIME WARRANTY
3. Applv a masking tape outline 1 8 outside traced outline as a guide for application of silicone sealant gt P no Sink Naki outline tape outline Apply a generous portion of silicone sealant inside line traced on countertop Carefully lower sink into place and press down firmly Use guidelines for proper positioning Using water to dampen your finger remove excess sealant for a smooth even line Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown Carefully remove tape Dampen finger and run it slightly over the sealant to remove any high spots Use mineral spirits to remove excess silicone from countertop and sink i l Silicone Sink Masking Sealant RS NOTE Silicone must be removed within 10 minutes of application or a permanent residue mav remain on the surfaces Connect supply lines to faucet finger tight and carefully bend to engage with the supply stops Tighten connections to faucet for secure seal Connect drain assembly hand tight to check alignment It may be necessary to cut off part of the tailpiece area A or part of the horizontal leg of the trap area B Secure joint for water tight assembly ce Trap Single Bowl CARE AND CLEANING For all porcelain enamel surfaces regular gentle care is best The recommended way to preserve the finish avoid scratches and clean porcelain enamel fixtures is to rin
4. screws Support Clips are for use in wood plywood or particle board drill a appropriate pilot hole The inserts supplied are for use in marble or hard synthetic material 790088 100 REV H Applv a bead of sealant to the edge of the sink Hold the Siok sink against the under side of Edge the countertop and rotate Sealant the clips to hold the sink in place Snug the screws to hold the sink Attach all the additional clips Countertop 41mm 1 5 8 Support Clip Countertop Mount the faucet and drain assembly following the manufacturer s instructions Connect supply lines to faucet finger tight and carefully bend to engage with the supply stops Tighten connections to faucet for secure seal Connect drain assembly hand tight to check align ment It may be necessary to cut off part of the tailpiece area A or part of the horizontal leg of the trap area B Secure joint for watertight assembly Trap l Trap Single Bowl Double Bowl INSTALLATION B FITTINGS MOUNTED DIRECTLY ON SINK Refer to American Standard roughing in information for specific dimensions for each model Below are the dimensions of each sink Make sure this area is available to mount the sink Unfold the template and refer to the instructions below ees 1 Minimum countertop thickness is 19mm 3 4 for wood and 12mm 1 2 for marble and solid surface materials SINK CUTOUTS Locate and mark center l
5. Installation Instructions CHANDLER AMERICAST ISLAND SINK WITH FAUCET HOLES 7182 001 7182 803 WITHOUT FAUCET HOLES 7182 000 Certified to comply with ANSI A112 19 4 M U S Patent No 4 664 982 Other patents pending CAN G S A B 45 Observe local plumbing and building codes Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin 791267 400 Rev C ISLAND SINK MODEL 7182 001 803 CUTOUT FOR NEW INSTALLATION 16 1 2 419mm BEFORE YOU BEGIN Unpack new sink and inspect carefully for damage Replace the sink in its original packing carton to protect it until you are ready to begin installation 14 356mm Recommended Tools amp Materials gt 8 11 32 Mineral Spirits 212mm Basin Wrench Saber Saw Tubing Cutter Silicone Sealant Putty Knife Pipe Wrench Channel Locks Phillips Screwdriver Regular Screwdriver Adjustable Wrench Drill Tape Measure Hacksaw Scissors CUTOUT DIMENSIONS FOR SINK Locate and mark center lines of sink on countertop Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet Cut out correct template and trace the cut line onto the countertop at the proper location NOTE If replacing an existing sink be certain to shut off water supplies before removing old sink
6. URES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCESESTABLISHED BV A N S I AND C S A STANDARDS SUPPORT CLIP LOCATIONS SUPPORT U L MODEL 7145 7163 STANDARD 7179 965mm 38 MODEL 7185 314mm 419mm 12 3 8 16 172 SUPPORT furs SUPPORT CLIPS MODEL 7103 790088 100 REV H 41 172 io 1054mm gt SUPPORT CLIPS 419mm 16 172 SUPPORT PS MODEL 7182 801 803 711mm e8 SUPPORT CLIPS SUPPORT MODEL 7173 635mm 25 SUPPORT CLIPS The following instructions are for NOTE ay countertop mounted fittings only Silhouette single bowl shown Countertop Template Drill a clearance hole inside the cutout line Cutout template Cut opening on cut line of the template Note Formica counter top installation only is illustrated Contact your countertop distributor for the best method of cut ting other materials such as marble hard syn thetics etc Countertop Countertop Cut fitting holes in the countertop and remove the template Template Cutout CAUTION Proper fit Fitting Prior to beveling the countertop Escutcheon edge be sure that the fitting escutcheon does not extend ew Countertop onto the curved portion of the countertop Attach at least four of the support clips to the underside of the countertop as shown below The location of the clips should be as shown in the sink diagram The wood
7. ines of sink on countertop Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet Do not use permanent markers to indicate the center lines e Cut the inner portion from the supplied template and discard Attach the outer portion of the template to the countertop using masking tape Be sure that the center lines on the template are aligned with those on the counter IMPORTANT DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY A N S I AND C S A STANDARDS SUPPORT CLIP LOCATIONS 965mm s 38 1054mm gt 41 172 n SUPPORT 559mm 22 l l A support CLIPS MODEL 7145 7163 STANDARD 7179 MODEL 7183 457mm i 18 635mm 16 1 2 25 a SUPPORT i i q SUPPORT CLIPS SUPPORT CLIPS MODEL 7185 419mm 16 172 i ape SUPPORT SUPPORT P 7 CLIPS ra CLIPS MODEL 7182 000 MODEL 7255 SUPPORT MODEL 7173 790088 100 REV H 4 The following instructions are for mounting fittings directly to the sink Silhouette single bowl shown Countertop Template Drill a clearance hole ki inside the cutout line Cutout template Cut opening on cut line of the template Note Formica counter top installation only is illustrated Contact your countertop distributor for the best method of cut ting other materials such as marble hard syn thetics etc Cou
8. nk itself below the countertop Use the correct instructions for vour application Recommended Tools amp Materials Silicone Sealant Drill Puttv Knife Basin Wrench Pipe Wrench Saber Saw Channel Locks Tubing Cutter Phillips Screwdriver Tape Measure Regular Screwdriver Hacksaw Adjustable Wrench Mineral Spirits INSTALLATION A FITTINGS MOUNTED ON COUNTERTOP Refer to American Standard roughing in information for specific dimensions for each model CAUTION 1 Minimum countertop thickness is 19mm 3 4 for wood and 12mm 1 2 for marble and solid surface material 2 Prior to pe countertop be sure that the fitting shank has sufficient length to attach the mounting nut after the shank goes through both the countertop and sink deck The deck is 3 8 10mm thick Below are the dimensions of each sink Make sure this area is available to mount the sink Unfold the template and refer to the instructions below SINK CUTOUTS Locate and mark center lines of sink on countertop Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet Do not use permanent markers to indicate the center lines Cut the inner portion from the supplied template and discard Attach the outer portion of the template to the countertop using masking tape Be sure that the center lines on the template are aligned with those on the counter 1 AMERICAN STANDARD INC 2003 IMPORTANT DIMENSIONS OF FIXT
9. nt to the following address In the United States American Standard Inc P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs In Canada American Standard 2480 Stanfield Road Mississauga Ontario Canada L4Y 1S2 For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 Toll Free 800 387 0369 790088 100 REV H Apply a bead of sealant to the edge of the sink Hold the sink against the under side of the countertop and rotate the clips to hold the sink in place Snug the screws to hold the sink Attach all the additional clips Countertop Cutout Edge Sealant 41mm l 1 5 8 Support Clip Countertop Surface a Mount the faucet and drain assembly following the manufacturer s instructions Connect supply lines to faucet finger tight and carefully bend to engage with the supply stops Tighten connections to faucet for secure seal Connect drain assembly hand tight to check align ment It may be necessary to cut off part of the tailpiece area A or part of the horizontal leg of the trap area B Secure joint for watertight assembly me Trap Trap Single Bowl Double Bowl CARE AND CLEANING For all porcelain enamel surfaces regular gentle care is best The recommended way to preserve the finish avoid scratches and clean porcelain enamel fixtures is to rin
10. ntertop Template Attach at least four of the support clips to the underside of the countertop as shown below The location of the clips should be as shown in the sink diagram The wood screws are for use in wood plywood or particle board drill appropriate pilot hole The inserts supplied are for use in marble or hard synthetic material Support J Clips Cutout AMERICAST LIMITED LIFETIME WARRANTY If an American Standard Americast brand product is found to be defective in materials or workmanship after inspection by an authorized American Standard representative American Standard will repair or at its option exchange the product for a similar model This warranty extends for the lifetime of the product so long as it remains in use in its original place of installation except that the warranty applies to a bathing vessel s slip resisting surface only for the first year after the product s initial installation This warranty applies only to the original purchaser and installation of these products This warranty does not apply to whirlpool components or to faucets drains mounting rims grab bars or other accessories If manufactured or supplied by American Standard such whirlpool components and accessories are covered under separate limited warranties This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this pr
11. oduct should check with a local building or plumbing contractor to assure local code compliance before installation This warranty shall be void if the Americast brand product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it was modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under these warranties it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be se
12. roduct as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under these warranties it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States American Standard Inc P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs In Canada American Standard 2480 Stanfield Road Mississauga Ontario Canada L4Y 1S2 Toll Free 800 387 0369 For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 791267 400 Rev C 5
13. se them with detergent and water Generally any of the light duty liquid dishwashing detergents such as Palmolive or Dawn work well In areas where the water is hard a heavy duty liquid laundry detergent such as liquid Tide will work better Product names listed herein are trademarks of American Standard Inc unless otherwise noted Palmolive is a registered trademark of Colgate Palmolive Co Tide and Dawn are registered trademarks of Procter and Gamble American Standard Inc 2003 Installation AMERICAST BRAND Instructions UNDERCOUNTER MOUNTING FOR CHANDLER LAKELAND PALISADE AND SILHOUETTE KITCHEN SINKS MODELS 7145 7162 7163 STANDARD 7103 7172 7173 7179 7182 7183 7185 7196 7255 Thank you for selecting American Standard the oleae TRE yy H Hi ertified to comply witi 19 4 benchmark of fine quality for over 100 years IG END E To ensure that vour installation proceeds smoothiv please Other patents pending read these instructions carefully before you begin Ge Observe local plumbing and building codes 790088 100 REV H BEFORE YOU BEGIN Unpack new sink and inspect carefully for damage Notify your American Standard distributor of any damage Replace the sink in its original packing carton to protect it until you are ready to begin installation NOTE The kit contains two tvpes of cutouts One cutout is for mounting the fitting on the countertop The second is for mounting the fitting on the si
14. se them with detergent and water Generally any of the light duty liquid dishwashing detergents such as Palmolive or Dawn work well In areas where the water is hard a heaw duty liquid laundry detergent such as liquid Tide will work better Product names listed herein are trademarks of American Standard Inc unless otherwise noted Palmolive is a registered trademark of Colgate Palmolive Co Tide and Dawn are registered trademarks of Procter and Gamble AMERICAN STANDARD INC 2003
Download Pdf Manuals
Related Search