American Standard Bathroom Aids Cadet 3 Concealed Trapway User's Manual
Contents
1. TROUBLESHOOTING GUIDE Problem Possible Cause See Step 11 For Diagram Corrective Action Does not Water supply valve closed flush Supply line blocked Flush valve chain too loose or disconnected Sand or debris lodged in water control Open valve and allow water to fill tank Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Readjust chain length as required Shut off water supply Remove cap and clean as per Fluidmaster maintenance instructions at www americanstandard us com enews fluidmasterguide pdf Poor or Bowl water level too low sluggish flush Supply valve partly closed Supply pressure too low Partially clogged trapway and or drain pipe and or vent Check that refill tube is connected to water control and inserted into overflow tube without being kinked or damaged Open supply valve fully Be sure that proper supply tube size is used Remove obstruction Consult a plumber if necessary Normal supply pressure must be at least 20 psi Toilet leaks a Poor supply line connection Poor bowl to tank floor connection Toilet does Review Step 10 of installation procedure Review Step 3 through 8 of installation procedure Clean debris from seal surface Replace flapper seal as needed Flapper seal leaking or deformed not shut off b Sand or debris lodged in water control Flush2. by toilet tank number which can be found marked inside tank NOTE XXX represents color or trim finish options Specify when ordering PART NUMBER DESCRIPTION 738903 XXX0A Tank Lever LH 4000 101 4000 004 1 28 gpf 1 6 gpf 4 8Lpf 6 0 Lpf 7381064 XXX0A Tank Lever LH 7301540 200 XXX0A Bolt Cap Kit consists of 2 caps 2 sleeves amp 2 retaining rings 7381125 400 0070A Fluidmaster 400A Inlet Valve 7381146 401 0070A Flushvalve Assembly 3 inch includes flapper 7381193 201 0070A Flapper Assembly 3 inch 7381146 406 0070A Flushvalve Assembly HET 3 inch includes flapper 7381193 203 0070A Flapper Assembly HET 3 inch 7381147 200 0070A EZ Install Tank Coupling Kit 735154 400 XXX Tank Cover 12 inch rough 735158 400 XXX Tank Cover 12 inch rough 5283 110 XXX Elongated Rim Seat Slow Close 5281 110 XXX Round Front Rim Seat Slow Close 5218 110 XXX Elongated Rim Seat Slow Close 5121 110 XXX Round Front Rim Seat Slow Close 738570 100 0070A Refill Tube 7381146 408 0070A Flushvalve Assembly 3 inch includes flapper 7381146 409 0070A Flushvalve Assembly HET 3 inch includes flapper 7381193 205 0070A Flapper Assembly 3 inch 7381193 206 0070A Flapper Assembly HET 3 inch 7381211 200 0070A Silicone Flapper Seal 7381167 200 0070A Bowl to Floor Knobs
3. from wall to closet flange centerline must be as listed below ee RIGHT HEIGHT ELONGATED 2 PIECE TOILET WALL va g amm aa IMPORTANT Water supply 221mm 399mm on the wall is required at 2 1 4 or 8 from centerline C L OF SEAT POST I ont Bvrens of the toilet see rough in l 14 r rl L aca First suggested position is SUPPLY E hidden behind the toilet The AS postion T or geometry of the toilet gives position 2 16 172 r y space for this installation 419mm The second suggested position is next to the toilet meee eee s rages Between these two P a S08min positions the space for the Rea alas RIGHT HEIGHT ROUND FRONT 2 PIECETOILET supply between wall and oe toilet is limited to 4 1 2 In this case check your supply and hose dimensions C L OF SEAT POST HOLES 5 1 2 i 140mm CENTERS 16 1 2 419mm AS REQUIRED 30 3 4 position 1 N 781mm or N NE position 2 16 1 2 i 419mm a 2 1 4 8 5 1 2 204mm 140mm I 1 i 71 2 12 7 8 P BACK VIEW 191mm gt 328mm FINISHED eas for reference FLOOR m 12 i 305mm Product names listed herein are trademarks of AS America Inc AS America Inc 2011 7301555 100 Rev B U SE FUTURE R F O SAVE Apply weight evenly Do not move after placement Water tight seal may break Thread
4. valve chain too tight holding flapper open Shut off water supply Remove cap and clean as per Fluidmaster maintenance instructions at www americanstandard us com enews fluidmasterguide pdf Readjust chain length as needed Toilet bowl rocks after installation For Repair Parts List See Under Tank Lid Wax ring not fully compressed Floor not level In the United States American Standard Brands P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 www americanstandard com In Canada AS Canada ULC 5900 Avebury Rd Mississauga Ontario Canada L5R 3M3 Toll Free 800 387 0369 www americanstandard ca Retighten bowl to floor knobs Use toilet shims and or place a bead of caulk around the base of the toilet In Mexico American Standard B amp K Mexico S de R L de C Via Morelos 330 Col Santa Clara Ecatepec 55540 Edo Mexico Toll Free 01 800 839 1200 www americanstandard com mx 4 7301555 100 Rev B
5. INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE American Standard Cadet 3 Concealed Trapway Studio Concealed Trapway Style That Works Better Right Height Elongated Model 2985 2989 2794 A S Right Height Round Front Model 2984 2988 2795 once Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this IAPMO RAT product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level IiE REMOVE OLD TOILET a Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl b Disconnect and remove supply line NOTE If replacing valve first shut off main water supply c Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases d Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed P ROUGHING IN DIMENSIONS NOTE Distance
6. then hand tighten water supply A HandTighten Only Do Not Overtighten Tighten handles alternately until tank contacts bowl HAND TIGHTEN ONLY TIP Place 2 pieces of masking tape on floor as shown to help with alignment in step 6 For seat installation see instructions included with seat A WARNING Overtightening of water supply line nuts could result in breakage and potential flooding If the connection leaks after hand tightening replace the supply line Do not use any type of sealant on the water supply connection A Use of plumber s putty pipe dope or any other type of sealant will void the warranty 7301555 100 Rev B Turn on water supply Adjust water level to level indicated on tank by turning water level adjustment knob to move float cup up or down Water Level Adjustment Knob Trip Lever Rod Fill Valve Or Water Control Refill Tube Approximate Water Level Tank to Bowl Gasket Water Supply Line CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth WARNING Do not use in tank cleaners These products can seriously corrode fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any damage caused by the use of in tank cleaners 7301555 100 Rev B REPAIR PARTS LIST Repair parts are determined
Download Pdf Manuals
Related Search