Home
American Standard 7500 Series User's Manual
Contents
1. base of CARTRIDGE CARTRIDGE m Replace CARTRIDGE until flange is tight against valve body Turn valves OFF m Replace BONNET NUT HANDLE SCREW and INDEX SCREEN Product names listed herein are trademarks of American Standard Inc American Standard Inc 1995 60185
2. Atutricam Standard Installation Instructions MONTERREY 7500 SERIES 7501 SERIES 7502 SERIES CENTERSET LAVATORY FAUCETS WITH GOOSENECK SPOUT Certified to comply with ANSI A112 18 1M PATENT PENDING Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin GRID DRAIN HANDLE SCREW INDEX RD BLADE HANDLE AERATOR 3 BONNET Se NUT LEVER POP UP v ROD CARTRIDGE POP UP DRAIN STOPPER O RUBBER S W ASHER CE BRASS WASHER U I ae LOCKNUT LV couPLinG NUT EXTENSION TAILPIECE Printed in Mexico Turn off hot and cold water CAUTION supplies before beginning SPOUT ___ E Asesemble GASKET to SHANKS and insert FAUCET SHANKS through holes of SINK ea a HM Assemble RUBBER and BRASS WASHERS and LOCKNUTS from underside of SINK Drop UPPER LIFT ROD through hole in BODY models 7501 only align BODY as far forward as possible RUBBER and secure position by tightening LOCKNUTS RING HM Connect the HOT water supply to the left SHANK and the COLD water supply to the right SPOUT SHANK using sealant appropriate connectors and COUPLING NUTS To change spout to a swivel spout Unscrew SPOUT NUT and remove SPOUT Take SPOUT CLIP off SPOUT and remove RUBBER RING Repl
3. ace RUBBER RING with seperate PLASTIC RING packed with faucet Put SPOUT CLIP on SPOUT Reassemble SPOUT to BODY GRID DRAIN ASSEMBLY M odel 7502 only HM Applya bead of PUTTY around underside of DRAIN PLUG flange Insert DRAIN PLUG into SINK drain hole Hold DRAIN PLUG to prevent turning and assemble GASKET WASHER and LOCKNUT from underneath sink Insert threaded end of TAILPIECE into lower end of DRAIN PLUG Connect other end to trap LOCKNUT TAIL PIECE 3 INSTALL POP UP DRAIN Model 7501 only HM Push TAILPIECE down into TRAP threaded end up HM Thread LOCKNUT WASHER and GASKET onto DRAIN BODY MH Apply a bead of PUTTY to underside of FLANGE HM Feed DRAIN BODY up through SINK and thread FLANGE fully onto BODY SINK Sa W Tighten LOCKNUT firmly keeping the PIVOT ROD pointed towards the back of the SINK HM Drop STOPPER into DRAIN BODY LOCKNUT Pull TAILPIECE up and thread tightly into DRAIN BODY TRAP a 4 TEST INSTALLED FAUCET Remove AERATOR E With handle in OFF position turn on water supplies and check all connections for leaks 909 y STOP d WASHER SERVICE To change direction of handle rotation proceed as follows m Turn valve to OFF position Remove HANDLE and BONNET NUT m Remove SPRING CLIP m Lift STOP WASHER turn 90 and replace m Replace SPRING CLIP m Replace BONNET NUT HANDLE SCREW and INDEX M AERATOR may accumulate d
4. irt causing distorted and reduced water flow Remove AERATOR and rinse clean SPRING CLIP 5 HOTLINE FOR HELP For toll free information and answers to your questions call 1 800 223 0068 W eekdays 8 00 a m to 4 00 p m Eastern Time __ _ STOPPER FLANGE x a t CLIP UPPER LIFT ROD PLASTIC RING NN CO RUBBER WASHER C BRASS WASHER _ LOCKNUT COLD COUPLING NUT m Position EXTENSION ROD onto POP UP ROD and tighten THUMBSCREW Mm Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding Insert PIVOT ROD into second or third hole in EXTENSION and reassemble CLIP EXTENSION may need to be bent THUMBSCREW iaee POP UP ROD PIVOT _ EXTENSION ROD 7_ CLIP TAILPIECE HM Adjust STOPPER height by repositioning EXTENSION and tightening THUMBSCREW Operate both handles to flush water lines thoroughly Check spout mounting and hose connections for leaks Operate LIFT ROD and check DRAIN for leaks Turn handles into OFF position and replace AERATOR If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow To clean first turn off hot and cold water supplies then m Remove HANDLE and BONNET NUT m Remove CARTRIDGE by pulling up m Thoroughly rinse plastic SCREEN at
Download Pdf Manuals
Related Search
Related Contents
1. Producto: ADITIVO FUNGICIDA ALGICIDA SpeedMark Tutorial 1 John Lewis JLWM 1604 Washer User Manual VPort 351 CGI Command User`s Manual Cataloguing and Search Module Epson Stylus Pro 5000 Print Engine Product Support Bulletin RAKOPOL EA BRILLO.cdr Miele DA 249 Specification Sheet PO-333 IM Copyright © All rights reserved.
Failed to retrieve file