American Standard 1480SS.500 User's Manual
Contents
1. B m Remove HANDLE CAP HOT LIMIT STOP and CARTRIDGE to adjust maximum discharge temperature Clean inlets and MANIFOLD Reassemble CARTRIDGE alternately tightening screws Replace HOT LIMIT STOP CAP and HANDLE Check flow a v B PRY FORWARD TO UNLOCK PRY FORWARD TO UNLOCK AND ROTATE COUNTER AND ROTATE CLOCKWISE CLOCKWISE ONE CLICK CARTRIDGE CARTRIDGE MTG SCREWS HOT LIMIT STOP ADJUSTMENT WHEN WATER IS TOO COLD ADJUSTMENT WHEN WATER IS TOO HOT M968395 Rev 1 12. Installation Instructions 1480 500 Sao 1480SS 500 T480 500 PRESSURE BALANCED BATH AND SHOWER FITTINGS Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1 U S Patent No D400 652 M968395 Rev 1 1 ROUGHING IN DIMENSIONS M To assure proper positioning in relation to wall note roughing in elation SHOWER dimensions te 1 5 8 TO FINISHED 3 1 4 ALL 1 2 LPS SHOWER OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN VALVE BODY O3 AND 7G WITH STOPS LEARANCE eal ADAPTOR AND MTG SCREWS 18 OPTIONAL X ry BATH CARTRIDGE 1 2 NPT j lt f HOT LIMIT ay K NA STOP ESCUTCHEON 1 2 COPPER OR1 2 NPT HANDLE INLETS 1 2 NOM INLETS COPPER NES en CARTRIDGE SHR 1 2 NOM SEALS COPPER SWEAT PRESSURE BALANCING SWEAT INLETS UNIT CARTRIDGE SCREW 41 16 TUB 1 2 NOM COPPER SWEAT gt L INLETS THREADED t 3 3 8 INLETS Lee piverTeR ESCUTCHEON 1 2 NPT SPOUT w INLETS 1 2 NPT X TUB port THREADED SWEAT 1 2 NPT INLETS STOPS INLETS STOPS SHR 1 2 NOM Sai PA lt 5 7 8 HOT LINE FOR HELP p 5 7 8 COPPER SWEAT For toll free information and answers to your quest
3. additional 1 holes to allow access to the stops TUB FILLER TUBES m Remove PLASTER GUARD rotate 180 so that indicated screw holes fit manifold 5 8 0 D 1 2 m Push CAP on valve place ESCUTCHEON and attach with screws NOMINAL Connect hot and cold water supplies For support use pipe BRACES secured to wooden braces REMOVE BURRS With valve turned off turn on water supplies and check for leaks FROM TUBE NOT INCLUDED INSTALL TRIM When finished tiling the wall remove PLASTER GUARD 4 h HANDLE BUSHING Push on CAP METAL Mount ESCUTCHEON with SCREWS Install HANDLE by pushing it onto CARTRIDGE STEM and tightening LEVER oo HANDLE CARTRIDGE STEM Ue SET SCREW from below ESCUTCHEON Install SHOWER ARM with FLANGE and SHOWER HEAD SCREWS Install SPOUT Check proper operation of HANDLE ESCUTCHEON and DIVERTER SPOUT HOT LIMIT STOP By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your SEVA faucets all you need to do adjust the setting on the HOT LIMIT SAFETY STOP If faucet drips operate handle several times from off to on Do not apply excessive force Clogged CARTRIDGE inlets may cause reduced flow in full on hot or cold To clean inlets first turn off water supply then Remove HANDLE CAP and HOT LIMIT STOP Follow A or
4. ions call sa INLETS 4 lt 1 800 442 1902 1 2 NOM 4 ane Weekdays 8 00 a m to 6 00 p m EST COPPER 3 9 8 _ O IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 SWEAT Weekdays 8 00 a m to 7 00 p m EST con L A IN MEXICO 01 800 839 1 2 00 TUB 1 2 NOM TUB PORT m 1 INLETS Product names listed herein are trademarks of American Standard Inc COPPER SWEAT 1 2 NPT 1 2 NPT AS America Inc 2008 CAUTION Turn off water at MAIN supply To prevent damage temporarily FLANGE remove STOPS when water supply lines are soldered to the manifold NOTE E SHOWER When soldering remove PLASTER GUARD CARTRIDGES and CHECK STOPS IF PRESENT When finished soldering flush valve body replace cartridges check stops if present and plaster guard to continue installation Use thread sealant or Teflon tape on threaded connections BRACE 4 ROUGHING IN E See Roughing in diagram on reverse side PIPE Connect RISER PIPE to MANIFOLD top outlet marked SHR Connect TUB FILLER PIPE at bottom outlet marked TUB Supply connections are m 1 2 copper sweat for sweat inlets E 1 2 female NPT for threaded inlets For proper positioning the finished wall must be within side wall of PLASTER GUARD NPT If the valve is installed on a fiberglass or other thin wall application the PLASTER GUARD can PLUG or be used as a support SWEAT PLASTER m Cut a 3 dia hole in the shower stall GUARD E f stops are used drill two
Download Pdf Manuals
Related Search