American Power Conversion NS 600 User's Manual
Contents
1. Back UPS NS 600 User s Guide WwWW apc com Connect Battery For safety the Back UPS NS is shipped with one battery wire disconnected The UPS will not operate until the wire is connected to the touch safe battery terminal NOTE Small sparks may occur during battery connection This is normal Turn the Back UPS NS over and press in the Connect the battery wire firmly to Insert the battery back into the compartment two release tabs Slide the plastic battery the battery terminal Slide the plastic battery cover in place until the cover off the unit two tabs lock into place Plastic Battery Release Tabs Cover Bs gt f E Battery Terminal Battery Wire Place the Back UPS NS to avoid Connect Equipment o S CA s P i Excessive humidity or contact with fluids lt A Battery Back up plus f Te LADUE Plug the Back UPS NS power cord directly into a wall outlet not a surge These outlets are powered whenever the Back UPS NS is protector or power sirip switched ON During a power outage or other utility problems Connect Computer Cable brownouts over voltages these outlets will be powered for a limited time by the Back UPS NS Plug your computer monitor CD ROM drive and one other data sensitive device such as an external disk or tape drive or Home Phoneline Connect the cable to the Data Port of the Back UPS NS Connect the other end of the Networking Associatio2. Power When indicator confirms the Back UPS NS is on an dicator co i siie ae URS NS le en eil On Line UPS is supplying conditioned Power LED ON None n a ready to provide protection utility power to the load The Back UPS NS should charge for at least 16 On Battery UPS is supplying battery Power LED ON Beeping 4 times UPS transfers back to hours to ensure sufficient runtime The unit is power to the load connected to the off during beep every 30 seconds On Line operation or i aes S Battery outlets when UPS is turned being charged whenever it is connected to utility off power whether the unit is turned ON or OFF Low Battery Warning UPS is supplying Power LED Flashing Rapid beeping half UPS transfers back to If the red Building Wiring Fault indicator located battery power to the load connected to second intervals On Line operation or T the Battery outlets and the battery is near when UPS is turned on the end near the power cord is lit your exhaustion off building wiring presents a shock hazard that E aa Replace Battery Battery needs to be Power LED Flashing Constant tone UPS turned off with should be corrected by a qualified electrician checked and or replaced or battery is not the power switch ae connected Install the PowerChute Personal Edition software Overload Shutdown During On Battery Power LED OFF Constant tone UPS turned off with operation a battery power supplied outlet the power s
3. condition When the unit beeps twice every second the battery has about 2 minutes of power remaining Immediately power down your computer and turn the unit OFF When normal power returns the unit will recharge the battery Call a qualified electrician for service Allow the unit to charge by leaving it plugged into the wall at least 16 hours As a battery ages the amount of runtime available will decrease You can replace the battery by ordering one at www apc com Batteries also age prematurely if the Back UPS NS is placed near excessive heat Make sure the data line from the wall outlet is connected to the jack labeled Wall Outlet Phone Fax DSL Plug the AC power cord of the modem into one of the four Battery Back up plus Surge Protection outlets Order Replacement Battery Replace with an APC qualified battery Replacement batteries can be ordered from www apc com valid credit card required Have your Back UPS NS model number available when ordering Your model number can be found on the bottom of the unit Warranty The standard warranty is 2 years from the date of purchase APC s standard procedure is to replace the original unit with a factory reconditioned unit Customers who must have the original unit back due to assigned asset tags and set depreciation schedules must declare such a need at first contact with APC Technical Support APC will ship the replacement unit once the defective unit is received by th
4. 5 Vrms 8 On Battery step approximated sine wave Frequency On Battery 50 60 Hz 1 Hz Transfer Time Protection and Filter AC Surge Protection 6 ms typical 10 ms maximum Full time 375 joules Phone fax DSL Surge Single line 2 wire Protection EMI RFI Filter Full time AC Input Resettable circuit breaker Battery Type Sealed maintenance free lead acid Average Life 3 5 years depending on the number of discharge cycles and environmental temperature Physical Net Weight 16 2 Ib 7 3 kg Size 4 0 H x 11 W x 7 1 D 10 2 x 27 9 x 18 03 cm Operating Temperature 32 F to 104 F 0 C to 40 C Storage Temperature 5 F to 113 F 15 C to 45 C Operating Relative Humidity Operating Elevation 0 to 95 non condensing 0 to 10 000 ft 0 to 3 000m Safety Regulatory Safety Approvals cTUVus NOM 001 EMC Compliance Notice This device complies with part 68 and part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation On the bottom of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telepho
5. e repair department or cross ship upon the provision of a valid credit card number The customer pays for shipping to APC and APC pays ground freight transportation costs back to the customer Service Please DO NOT RETURN Back UPS NS to the place of purchase under any circumstances 1 Consult the Troubleshooting section to eliminate common problems 2 Verify the battery is connected see Connect Battery and that the Circuit Breaker is not tripped see Troubleshooting section If you still have problems or questions please contact APC via the internet or at one of the phone numbers listed below 3 Before contacting APC please be sure to record the date purchased UPS model and serial number on bottom of unit 4 Be prepared to troubleshoot the problem over the telephone with a Technical Support Representative If this is not successful the representative will issue a Return Material Authorization Number RMA and a shipping address 5 Pack the unit in its original packaging If the original packaging is not available ask APC Technical Support about obtaining a new set Pack the unit properly to avoid damage in transit Never use foam beads for packaging Damage sustained in transit is not covered under warranty insuring the package for full value is recommended 6 Write the RMA on the outside of the package 7 Return the unit by insured carrier to the address given to you by APC Technical Support APC Contact In
6. formation Online Technical Support http support apc com http Awww apc com support esupport apcc com Web Site www apc com USA Canada 1 800 800 4272 Mexico 52 292 0253 52 292 0255 Brazil 0800 12 72 1 Worldwide 1 401 789 5735
7. n HPNA device into these outlets cable to the USB port on your computer The software will automatically find the USB Port of your computer Connect Modem Phone DSL Fax HPNA to Surge Protection The Back UPS protects a single line 2 wire phone including Digital Subscriber Line DSL Home Phoneline Networking Association HPNA type equipment modem or fax machines from surges when connected through the UPS as shown below P The supplied cable and software provide automatic file saving and shutdown of the operating system in the case of a sustained power outage FROM WALL JACK WALL E OUTLET DSL MODEM H FAX DATALINE OUTPUT TO DSL f s MODEM PHONE Surge Protection TO COMPUTER USB PORT ael pen These outlets provide full time protection from surges even if the Back UPS NS is switched OFF Plug your printer fax machine scanner or other peripherals that do not need battery power into these outlets Breaker D gt Power On and Status Indicators 9 amp 7 Building Wiring P UPS Power Indicator O The Back UPS NS indicates operating status Fault Indicator nsta 0 tware using a combination of visual and audible Power indicators Switch Press the ON OFF switch to power the unit ON i Status Visual Indicators Audible Indicators Alarm Terminates A single short beep and the green
8. ne company Connect the battery see Connect Battery and ensure power is available at the wall outlet Reduce the amount of equipment plugged into Surge Protection outlets Ensure the fuse or circuit breaker for the outlet is not tripped and that the wall switch controlling the outlet if any is in the ON position Ensure the equipment you want to stay powered during a power failure is plugged into the Battery Backup plus Surge Protection outlets and NOT the Surge Protection outlets Make sure the equipment plugged into the outlets of the unit are not overloading its capacity Try removing some of the equipment and see if the problem continues The Back UPS NS is operating normally The Back UPS NS can only operate on battery power for a limited amount of time The unit will eventually turn off when the available battery power has been used Allow the unit to recharge for 16 hours before expecting maximum runtime The output waveform is designed for computers and computer related equipment It is not designed for use with motor type equipment Contact APC Technical Support for further troubleshooting The Back UPS NS is operating normally and using battery power Once On Battery you should save your current work power down your equipment and turn the unit OFF Once normal power is restored you may turn the unit back ON and power your equipment The Back UPS NS is about to shut off due to a low battery charge
9. twice per second at the same time Building Wiring Fault indicator is lit Inadequate runtime No phone fax DSL signal from the Back UPS Internet connection is lost during power outage Specifications Battery is disconnected or utility power is not available at the wall outlet Surge Protection outlets have been overloaded Utility power not available at the wall outlet Equipment is connected to the Surge Protection outlets The Back UPS NS is overloaded PowerChute Personal Edition software has performed a shutdown due to a power failure The Back UPS NS has exhausted its available battery power Connected equipment does not accept the step approximated sine waveform the Back UPS NS The Back UPS NS may require service The Back UPS NS is using battery Battery capacity is low about 2 minutes of use remaining Your building wiring presents a shock hazard Using the Back UPS with this condition will void the warranty The battery is not fully charged Battery is near the end of useful life Data line from the ISP or wall outlet is connected to the wrong jack on the Back UPS Modem has lost AC Power Model BN600 Input Voltage 120 Vrms Nominal Frequency 50 60 Hz auto sensing Brownout Transfer 88 Vrms typical Over voltage Transfer 139 Vrms typical Output UPS Capacity 4 outlets 600 VA 360 W Total Amperage 8 outlets 12 Amps including UPS output Voltage 11
10. witch Place the PowerChute Personal Edition CD Cener wee Gees ROM into your computer and follow the Sleep Mode During On Battery Power LED OFF Beeping once every Utility power is installation instructions on the screen operation the battery power has been 4 seconds restored or if utility completely exhausted and the UPS is power is not restored waiting for utility power to return to within 32 seconds or normal the UPS is turned off Building Wiring Fault Your building Building Wiring Fault None UPS is unplugged or wiring presents a shock hazard that LED red ON plugged into a should be corrected by a licensed properly wired outlet electrician See the Troubleshooting section for additional assistance 990 2437A Copyright 2007 American Power Conversion Corp APC Back UPS and PowerChute are registered trademarks of American Power Conversion Corp All other trademarks are property of their respective owners Troubleshooting Use the table below to solve minor Back UPS NS installation or operation problems Consult APC Online Technical Support or call APC Technical Support for assistance with problems that cannot be resolved using the table below Back UPS NS will not turn on No power available at the Surge Protection outlets Connected equipment loses power The Power indicator is lit and the Back UPS NS is beeping four times every 30 seconds The Power indicator flashes and the Back UPS beeps
Download Pdf Manuals
Related Search