American Power Conversion Generator User's Manual
Contents
1. position Conversion Kit Installation 1 Open the generator enclosure 2 Locate the gas solenoid valve and pull the two connectors off of the solenoid Front View Generator Enclosure you Generator Ee Stand Off Relay to be Tie Wrapped to Stand Off 4 l VA Za O Power Supply and Long Transponder s y Harness Solenoid located in attached A j Connectors on onduit enclosure New Short Valve Harness Original n Solenoid Wires 7 E New Long Harness Original New Short Solenoid Wires Harness CE No Connection 4 Route the new long harness along the outer edges of the enclosures following the path of the original wiring as closely as possible Use tie wraps when necessary 5 Attach the new long harness to the transponder in the CTEG4M Enclosure See figure below for details Meter Rear View CTEG4M Enclosure XP7 connector for transponder Existing Wiring harness for Generator Control Transponder Ground Bar New long harness B Attach the wire A Cut the original previously cut from wire to Pin 7 Attach Pin 7 to the ground the new long harness bar using a butt wire to the plug side splice Wire NOT using a butt splice included 6 Verify system functionality e Force the engine to crank allowing failure to start An error message should appear at the head end site e Turn the generator ON Head e2. ckets are in good condition Replacement of fuses or other parts must be with identical types and ratings Substitution of nonidentical parts may cause safety and fire hazards Overhead Never stand below anything while 1t is hoisted Always wear a hard hat Warnings Lifting Transformer modules are heavy Use proper lifting equipment and techniques Warnings to avoid injury Battery Danger of explosion if battery is incorrectly connected or replaced Replace Warnings batteries only with same or equivalent type recommended by the manufacturer R Batteries must be recycled Deliver the battery to an appropriate recycling 1 N facility or ship it to the supplier in the new battery packing material Pb Chapter 2 Installation and Maintenance Only trained service personnel should install and maintain the Power Supply Unpacking The packaging is recyclable save it for reuse or dispose of it properly Check the package contents The package contains the following Quantity Description 1 Relay 12VDC 2 Butt Splice 1 Long Wire Harness 1 Short Wire Harness Power Shutdown Procedure The generator power supply must be shutdown prior to installing the Conversion Kit 1 Ensure that the CTEG4M Enclosure is NOT running on generator power 2 Disconnect the cable from the negative battery terminal in the generator enclosure 3 Switch the battery circuit breaker to the OFF position 4 Switch the utility circuit breaker to the OFF
3. days of purchase EXCEPT AS PROVIDED HEREIN AMERICAN POWER CONVERSION MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL APC BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically APC is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise Entire contents copyright O 2002 by American Power Conversion Corporation All rights reserved Reproduction in whole or in part without permission is prohibited APC is a registered trademark of American Power Conversion Corporation All other trademarks are the property of their respective owners
4. n obtaining appropriate packing materials m Pack the unit properly to avoid damage in transit Never use Styrofoam beads for packaging Damage sustained in transit is not covered under warranty 3 Mark the RMA on the outside of the package 4 Return the unit by insured prepaid carrier to the address given to you by Customer Service How to Contact APC In the USA Outside the USA Refer to the APC web site Refer to the APC web site www apc com Select the appropriate www apc com support country from the country selection field Select the Support tab at the top of the web page Limited Warranty American Power Conversion APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its own sole option any such defective products To obtain service under warranty you must obtain a Returned Material Authorization RMA number from customer support Products must be returned with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way This warranty applies only to the original purchaser who must have properly registered the product within 10
5. nd site operators should see the engine status as ON e Turn the generator OFF Head end site operators should see the engine status as OFF Connect Power to the Enclosures 1 Reconnect the battery in the generator enclosure 2 Switch the battery circuit breaker ON 3 Switch the utility circuit breaker ON Chapter 3 Service Contact and Warranty Information Service APC makes every effort to ensure parts and equipment arrive in working condition Occasionally it may be necessary to return parts or equipment that are not in working condition If the unit requires service do not return it to the dealer Instead follow these steps 1 Contact APC Customer Service through the APC web site www apc com support Note the product model number the serial number and the date purchased If you call APC Customer Service a technician will ask you to describe the problem and try to solve it over the phone If this is not possible the technician will issue a Returned Material Authorization Number RMA m Ifthe product is under warranty repairs are free If not there is a repair charge Procedures for servicing or returning products may vary internationally Refer to the APC web site Select the appropriate country from the country selection field Select Support from the tab at the top of the web page 2 Pack the product in its original packaging If the original packing is not available refer to the APC web site for information o
6. www apc co Additional Generator Status Monitoring User s Manual 990 1217 07 02 Chapter 1 General Information The Conversion Kit is used to provide additional status monitoring capabilities for the Generac Bowman generator Safety This Safety Guide contains important instructions that should be followed during installation and maintenance of the APC equipment and batteries It is intended for APC customers who setup install relocate or maintain APC equipment Changes and modifications to this unit not expressly approved by APC could void the warranty Installation initial start up and maintenance should be carried out by a qualified electrician Read the Safety Information included in the User s Manual for the generator Failure to observe these warnings may result in serious injury or death or damage to the equipment Electrical Do not work alone under hazardous conditions Warnings Do not handle any metallic connector before the power has been disconnected Servicing this equipment may require working with protective covers removed and AC power connected Use extreme caution during these procedures High current through conductive materials could cause severe burns When grounding cannot be verified disconnect the equipment from the utility power outlet before installing or connecting to other equipment Reconnect the power cord only after all connections are made Check that the power cord s plug s and so
Download Pdf Manuals
Related Search