Amana NGD4705EW Dimension Guide
Contents
1. runs longer than those specified Rigid metal 120 ft 36 6 m in Vent System Chart Exhaust systems longer than those specified will _ Rigid metal 110 ft 83 5 m m Shorten life of dryer m Reduce performance resulting in longer drying times ME eecencia sae g Set Ja Rigid metal 100 ft 30 5 m Determine vent path 7 E Select route that will provide straightest and most direct Rigid metal 90 ft 27 4 m path outdoors hal Plan installation to use fewest number of elbows and a Rigid metal 80 ft 24 4 m urns m When using elbows or making turns allow as much 5 Rigid metal 70 ft 21 3 m room as possible E Bend vent gradually to avoid kinking m Use as few 90 turns as possible Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation our products we reserve the right to change materials and specifications without notice Instructions packed with product Specifications subject to change without notice2. Amana Gas Dryer PRODUCT MODEL NUMBERS NGD4600Y NGD4700Y NGD4655E NGD4705E Installation clearances The location must be large enough to allow the dryer door to open fully Most installations require a minimum 5 2 140 mm clearance behind the dryer for the exhaust vent with elbow See Venting Requirements 29 Wide Models Dryer Dimensions 43 1102 mm 13 it 849 mm ean v 705 mm x 737 mm 737 mm A B A Wide opening side swing door B Wide opening hamper door Installation Spacing 48 in 310 cm NELE LI EIEEEI XIL N 0 0 0 00001 ait _ 76mm A 24 in 155cm gt 15 lt 737 mm 25mm 25mm 705mm 140 mm A B C A Recessed area B Side view closet or confined area C Closet door with vents 25 mm Required spacing Installation spacing for recessed area or closet installation 27 Wide Models Dryer Dimensions 2334 _ 603 mm 43 v 1092 mm 1092 mm ax A 29 1 2 29 1 2 749 mm aa LAN 749 mm a aN e 686 mm Ne 686 mm A B A Large opening side swing door B Wide opening hamper door Installation Spacing 48in 310 cm 18 457 mm Li gii 76 mm A p 4 p p 4 4 p p 4 p 4 y p y p 5 p 4 p 4 p 4 p 4 4 gt 27 gt ea Ht 29015 25mm 686mm 25 mm 25mm 749 mm 140 mm A B C A Recessed area B Side view cl
3. S ONLY REQUIREMENTS The dryer must be connected to the cold water faucet using new inlet hoses Do not use old hoses Do not overtighten Damage to the coupling can result VENTING REQUIREMENTS _ The Vent System Chart provides venting requirements that will help achieve best drying performance Exhaust venting Exhaust your dryer to the outside 4 102 mm diameter vent is required Rigid or flexible metal exhaust vent must be used Do not use plastic or metal foil vet Exhaust hood Vent System Chart must be at least 12 305 mm from the ground or any object that Number of Type Box louvered may be in the path of the exhaust 90 turns or of vent hoods Exhaust hoods elbows Recommended Styles Rigid metal 54 ft 16 5 m 48 ft 14 6 m Ta 2 gia meta 44 ft 13 4 m 38 ft 11 6 m louvered Hood Box Hood a Rigid metal 35 ft 1 0 7 m 29 Tt 8 8 m Acceptable Style 4 Rigid metal 27 ft 8 2m 21 ft 6 4 m NOTE Side and bottom exhaust installations for 27 wide models have a 90 turn inside the dryer To determine maximum exhaust length add one 90 turn to the chart Angled Hood Vent System Chart Determine vent length and elbows needed for best 29 Wide Long Vent Models Only drying performance Number of Type Box louvered or l 90 turns of vent Angled hoods m Use Cae Rut System Chart to determine type of vent or elbows material and hood combinations acceptable to use NOTE Do not use vent
4. oset or confined area C Closet door with vents Required spacing The dimensions shown below are for the recommended spacing for this dryer be considered Additional spacing should be considered for ease of installation and servicing Additional clearances might be required for wall door and floor moldings and dryer venting Additional spacing of 1 25 mm on all sides of the dryer is recommended to reduce noise transfer For closet installation with a door minimum ventilation openings in the top and bottom of the door are required Louvered doors with equivalent ventilation openings are acceptable Companion appliance spacing should also W10514185A 02 2015 INSTALLATION REQUIREMENTS GAS SUPPLY REQUIREMENTS Gas supply This dryer is equipped for use with Natural gas Dryer can be converted to L P gas When rigid pipe is used it should be 1 2 IPS When acceptable to the gas supplier and local codes 3 8 approved tubing may be used for lengths under 20 ft 6 1 m For lengths over 20 ft 6 1 m larger tubing should be used Pipe joint compounds resistant to the action of L P gas must be used An La manual shutoff valve must be installed within 6 ft 1 8 m of the dryer in accordance with the National Fuel Gas Code ANSI Z223 1 ELECTRICAL REQUIREMENTS A 120 volt 60 Hz AC only 15 or 20 amp fused electrical supply is required A time delay fuse or circuit breaker and a separate circuit are recommended WATER STEAM MODEL
Download Pdf Manuals
Related Search