Alliance Laundry Systems W001C User's Manual
Contents
1. 120 Volts AC alternating current 15 Amps Refer to Figure 17 for determining correct polarity of the wall receptacle 120 12 STANDARD 120 VOLT 60 HERTZ 3 WIRE EFFECTIVELY GROUNDED CIRCUIT Dogol L1 Ground Neutral Side Round Grounding Prong Neutral a BR ND Figure 17 DO NOT OPERATE OTHER APPLIANCES ON THE SAME CIRCUIT DO NOT OVERLOAD CIRCUITS 14 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 NOTE Some models come without an electrical plug installed If washer is not hard wired refer to Figure 19 a suitable plug that meets local electrical standards including earthing requirements must be installed Refer to the washer nameplate for proper voltage and Hertz the washer is designed to operate on Refer to Figure 18 To reduce the risk of electric shock or fire DO NOT use an extension cord or an adapter to connect the washer to the electrical power source 120 Volt 50 Hertz This washer is designed to be operated on a separate polarized three wire earth grounded 120 Volt 50 Hertz single phase electrical circuit protected by a 15 ampere fuse equivalent fusetron or circuit breaker DO NOT OPERATE OTHER APPLIANCES ON THE SAME CIRCUIT WHEN THE WASHER IS OPERATING 240 Volt 50 Hertz This washer is designed to be operated on a separate polarized three wire earth grounded 240 Volt 50 Hertz single phase electrical circuit protected by2. a 10 ampere fuse equivalent fusetron or circuit breaker DO NOT OPERATE OTHER APPLIANCES ON THE SAME CIRCUIT WHEN THE WASHER IS OPERATING 230 Volt 50 Hertz This washer is designed to be operated on a separate polarized three wire earth grounded 230 Volt 50 Hertz single phase electrical circuit protected by a 10 ampere fuse equivalent fusetron or circuit breaker DO NOT OPERATE OTHER APPLIANCES ON THE SAME CIRCUIT WHEN THE WASHER IS OPERATING Installation W3341 1 Nameplate Figure 18 240 Volt 60 Hertz This washer is designed to be operated on a separate polarized three wire grounded 240 Volt 60 Hertz single phase electrical circuit protected by a 10 ampere fuse equivalent fusetron or circuit breaker DO NOT OPERATE OTHER APPLIANCES ON THE SAME CIRCUIT WHEN THE WASHER IS OPERATING Earthing Grounding Instructions The washer must be earthed grounded In the event of malfunction or breakdown earthing will reduce the risk of electric shock by providing a path of least resistance for electric current The washer is equipped with a cord having an equipment earthing conductor Some models are also equipped with a three prong earthing plug The washer must be plugged or hard wired into an appropriate power source that is properly installed and earthed in accordance with all local codes and ordinances Improper connection of the equipment earthing conductor can result in a risk of electric s
3. a ae sncinteeesanstooteeses 15 240 Volt SO Hefi it ra set ns Re e en ententes 15 230 Volt SO Herta i irrasionale 15 240 VOIL 00 Herta EE ne rentree ile nette see 15 Earthing Grounding Instructions 15 Water Supply Requirement cccccccescesseeesecseeseeseeeeeeeeeceeneesseeaes 17 Water Temperatur eniran eroi e a En TE TEE 17 Water Pressure niecne ti a aa ie e neat ta iea 17 RISCTS e r a Mr ho ee E ve en EE tee 18 Installer Checklist Back Cover Copyright 2007 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 1 Notes Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Replacement Parts If replacement parts are required contact the source Alliance Laundry Systems from which you purchased your washer or contact Shepard Street P O Box 990 Ripon WI 54971 0990 Phone 920 748 3950 for the name and address of the nearest authorized parts distributor 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Notes Copyright Alliance Laundry Systems LLC DO
4. and Shipping Plug NOTE Install dryer before washer This allows room for attaching exhaust duct Remove the shipping brace from under the lid The plastic shipping plug will be released from the base of the washer when removing the cardboard base from the washer TLW521N 1 Shipping Brace 2 Shipping Plug Figure 2 NOTE Do not tilt washer to front or sides when moving The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location This will prevent damage to washer components NOTE Refer to your Operating Instructions for reinstalling shipping brace and shipping plug 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Step 2 Wipe Out Inside of Washtub Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub W3711 Figure 3 Installation Step 3 Connect Fill Hoses NOTE Refer to section on Water Supply Requirements before connecting fill hoses The appliance is to be connected to the water mains using new hose sets and old hose sets should not be reused Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve NOTE When installing in newly constructed or r
5. sufficient cooling to prevent pump seal damage NOTE The agitator should not be removed except for service The washtub is designed to be self cleaning W3911 Figure 14 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 13 Installation Electrical Requirements NOTE The wiring diagram is located in the control hood To reduce the risk of fire electric shock or personal injury all wiring and earthing MUST conform with the latest edition of the National Electrical Code ANSI NFPA 70 and such local regulations as might apply It is the customer s responsibility to have the wiring fuses and circuit breakers checked by a qualified electrician to make sure your home has adequate electrical power to operate the washer DO NOT OVERLOAD CIRCUITS DO NOT USE ADAPTER DO NOT USE AN EXTENSION CORD Doogl Figure 16 NOTE Refer to the washer nameplate for proper voltage and Hertz the washer is designed to operate on Refer to Figure 18 120 Volt 60 Hertz With 3 Prong Grounding Plug This washer is designed to be operated on a separate branch polarized three wire effectively grounded 120 Volt 60 Hertz AC alternating current circuit protected by a 15 ampere fuse equivalent fusetron or circuit breaker The three prong grounding plug on the power cord should be plugged directly into a polarized three slot effectively grounded receptacle rated 110
6. 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 9 Installation High Standpipe Installation Place the hose into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose approximately 30 cm 12 inches down from the top of pipe and tighten strap to hold hose to standpipe This will prevent the drain hose from dislodging from drain receptacle during use 2 TLW1962N 1 Drain Hose 2 Standpipe Standpipes higher than 122 cm 4 feet are not recommended 3 Tie Down Strap 4 Standpipe Adapter Figure 7 Low Standpipe Installation No 562P3 Siphon Break Kit is required for this type of installation This kit is available as optional equipment at extra cost through an authorized dealer or parts distributor Installation instructions are supplied with the kit W5121 1 562P3 Siphon Break Kit 2 Standpipe 3 Drain Hose Figure 8 10 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Sink Installation For this type of installation use the beaded tie down strap supplied in accessories bag or use a large wire tie available from your local hardware store and secure the drain hose to the cabinet top hinge Refer to Figure 9 This will prevent the drain hose from dislodgin
7. Automatic Washers Home Laundry uOneT eIsUy Keep These Instructions for Future Reference If this machine changes ownership this manual must accompany machine lance Re Laundry Systems www comlaundry com April 2007 Ta b e of Replacement Parts 3 Installation ter raie een ate Heat a 5 C on te nt S Roughing in Dimensions sss ssl ce cd dot 5 Before You Start foie esineen e bebe agees ea a eG cnet 6 TOOLS ren nn ee EE E A a apenas nat bus 6 VCC tii Callies EE nr ENS tat an ne Shah ets ae nn 6 Water Re te uen ed e ne dane dames Lane des Ve 6 Installing the Washer ccccccccsccessceeseeseeesseeseeseeeeneeseecsaecneeseeeeeeeeaeesaes 7 Step 1 Remove the Shipping Brace and Shipping Plug 7 Step 2 Wipe Out Inside of Washtub 0 00 0 ccceccescesseeteeetseeteenaeens 7 Step 3 Connect Fill Hoses 8 Step 4 Connect Drain Hose to Drain Receptacle 0 0esss1se1see 9 Step 5 Position and Level the Washer cccccscesseeteceteeeteeesees 12 Step 6 Connect the Washer to Electrical Power eseesesereeees 13 Step 7 Add Water to the Washer cccecccsesseceteeeeeeeeeetseeseeeneens 13 Step 8 Check Lid Switch 13 Step 9 Check Installation 13 Electrical Requirements 14 120 Volt 60 Hertz With 3 Prong Grounding Plug 14 120 VOLS H T Z nr rR en din nr
8. NOT COPY or TRANSMIT 38900 Roughing in Dimensions Installation 65 cm 25 6 in With leveling legs turned into base 38900 73 7 cm 29 in gt eo st E 5 N a e x 91 4 cm 36 in 56 2 cm 22 13 in 71 1 cm 28 in 134 6 cm 53 in 102 2 cm 40 25 in Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT TLW2075N Installation Before You Start Tools For most installations the basic tools you will need are Electrical Refer to serial plate for specific electrical requirements For more detailed information refer to section on Electrical Requirements Water Washer needs two standard 19 1 mm 3 4 inch water supply faucets with a pressure between 138 and 827 kPa 20 to 120 pounds per square inch For more detailed information refer to section on Water Supply Requirements D0741 1 Wrench 2 Screwdriver 3 Pliers 4 Level Figure 1 6 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Installing the Washer NOTE If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up Step 1 Remove the Shipping Brace
9. TRANSMIT 38900 Step 4 Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp Find the instructions on the following pages that are appropriate for your type of drain receptacle standpipe high standpipe low standpipe sink wall or laundry tub Follow these instructions to properly install the drain hose IMPORTANT Drain receptacle must be capable of handling a minimum of 3 2 cm 1 1 4 inch outside diameter drain hose i ow A 7 WA Cra SS TK fe a W324 1 Retainer Clamp Standpipe Adapter Figure 5 Installation Standpipe Installation Place the hose into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose approximately 30 cm 12 inches down from the top of pipe and tighten strap to hold hose to standpipe This will prevent the drain hose from dislodging from drain receptacle during use IMPORTANT To prevent siphoning do not place any ribbed portion of the drain hose into the standpipe 19 44 cm 36 in RECOMMENDED HEIGHT TLW1961N Ribbed Portion of Drain Hose Standpipe Adapter Tie Down Strap Standpipe 5 08 cm 2 in or 4 cm 1 1 2 in Diameter 5 Drain Hose Sleeve BR ND Figure 6
10. an open flame during this time W029 NOTE Water supply faucets must fit standard 19 1 mm 3 4 inch female garden hose couplings DO NOT USE SLIP ON OR CLAMP ON CONNECTIONS NOTE Water supply faucets should be readily accessible to permit turning them off when washer is not being used W1871 Water Supply Faucets Cold Water Connection Hot Water Connection Fill Hoses BR ND Figure 20 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Water Temperature Cold Recommended cold water temperature is 10 to 24 Celsius 50 to 75 Fahrenheit Hot Recommended hot water temperature is 60 to 66 Celsius 140 to 150 Fahrenheit Warm Mixture of hot and cold water Warm water temperature is dependent upon the water temperature and the pressure of both the hot and cold water supply lines IMPORTANT Turn off water supply faucets after check out and demonstration Owner should turn off water supply whenever there will be an extended period of non use NOTE Longer fill hoses are available as optional equipment at extra cost if the hoses supplied with the washer are not long enough for the installation Order hoses as follows No 20617 Fill Hose 2 44 m 8 feet No 20618 Fill Hose 3 05 m 10 feet Water Pressure Pressure must be a minimum of 138 to a maximum of 827 kPa 20 to 120 pounds per square inch static p
11. enovated building it is very important to flush the lines since build up may have occurred during construction Remove the two plain rubber washers and two filter screens from accessories bag and install them according to Figure 4 NOTE Check filter screens for debris or damage annually Clean or replace them if necessary IMPORTANT Thread hose couplings onto valve connections finger tight then approximately 1 4 turn with pliers DO NOT cross thread or overtighten couplings Turn water on and check for leaks If leaks are found retighten the hose couplings Continue tightening and rechecking until no leaks are found TLW1988N Filter Screen Screen must be facing outward Fill Hose Rubber Washer Plain Cold Water Connection Hot Water Connection Install this end of hose to valve connections at rear of washer 7 Install this end of hose to water supply faucet Black colored coupling for metric 8 Faucet ou kh WN Figure 4 IMPORTANT Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a yearly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every 5 years 8 Copyright Alliance Laundry Systems LLC DO NOT COPY or
12. g during use Installation In the Wall Installation For installations of this type the drain hose MUST be secured to one of the inlet hoses using the beaded tie down strap from accessories bag NOTE End of drain hose must not be below height of cabinet top TLW1963N 1 Drain Hose 2 Tie Down Strap or Wire Tie 3 Cabinet Top Hinge Figure 9 W3291 1 Tie Down Strap Tape if necessary 2 Standpipe Adapter Figure 10 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11 Installation Laundry Tub Installation For this type of installation the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use Use the beaded tie down strap supplied in accessories bag to secure hose TLW1964N 1 Tie Down Strap Tape if necessary Figure 11 Step 5 Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing Place rubber feet on all four leveling legs Place washer in position on a clean dry and reasonably firm floor Installing the washer on any type of carpeting is not recommended Loosen 7 8 inch locknuts and adjust the two front leveling legs Once adjusted tilt the unit forward on front legs and lower back down into
13. hock Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly earthed W032 Do not modify the plug provided with the washer if it will not fit the outlet have a proper outlet installed by a qualified electrician 38900 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 15 Installation HARD WIRED PLUG W403 W402 NOTE Electrical receptacle must be located so that it is easily accessible with machine in place If machine is hard wired an intermediate shut off box with a 3 mm gap is required to meet EN 60335 1 clauses 24 3 and 22 2 or 3 5 mm gap is required to meet Standard IEC 60335 1 clauses 24 3 and 22 2 Gap is defined as the minimum contact separation of each pole in the switch between the ON and OFF positions Figure 19 16 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Water Supply Requirements Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for sucha period and before using the washer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable Do not smoke or use
14. position to set the rear self leveling legs Washer must not rock After washer is at desired height tighten locknuts securely against bottom of washer base If these locknuts are not tight washer will not remain stationary during operation Improper installation or flexing of a weak floor will cause excessive vibration Do not slide washer across floor once the leveling legs have been extended as legs and base could become damaged Verify that washer doesn t rock wi79l Level Locknut Leveling Leg Rubber Cup Washer Base a ND Figure 12 12 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Installation Step 6 Connect the Washer to Electrical Step 8 Check Lid Switch Power Washer should stop agitating and spinning when lid is Refer to section on Electrical Requirements and opened connect the washer to an electrical power source W376l D2541 Figure 15 Figure 13 Step 9 Check Installation Step 7 Add Water to the Washer Refer to Installer Checklist on the back cover of this To prevent damage to pump do not run washer before manual and make sure that washer is installed adding at least one quart water to the tub If the washer correctly is run before any water is added the pump seal may overheat causing the pump to leak Once installed the water retained in the drain system from the previous cycle will provide
15. ressure measured at the faucet NOTE Water pressure under 138 kPa 20 pounds per square inch will cause an extended fill time in the washer 17 Installation Risers Risers or air cushions may have to be installed if the pipes knock or pound when flow of water stops The risers are more efficient when installed as close as possible to the water supply faucets Refer to Figure 21 woos 1 Risers Air cushions 2 Water Supply Faucets Figure 21 18 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38900 Installer Checklist Fast Track for Installing the Washer Refer to the manual for more detailed information e Remove the Shipping Brace and Shipping Plug CHECK e Wipe Out Inside of Washtub Connect Fill Hoses TLW1988N e Connect Drain Hose to Drain Receptacle TC Re W315IE0A CT creer e Position and Level the Washer D259 Connect the Washer to Electrical Power Add Water to the Washer eS CHECK O e Check Lid Switch CHECK
Download Pdf Manuals
Related Search