Alliance Laundry Systems LWK74A-3050 User's Manual
Contents
1. 102 2 cm 40 25 in TLW2075N 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Before You Start Electrical Tools Refer to serial plate for specific electrical requirements For more detailed information refer to For most installations the basic tools you will need section on Electrical Requirements ane Water Washer needs two standard 19 05 mm 3 4 inch water 3 supply faucets with a pressure between 138 and 2 827 kPa 20 to 120 pounds per square inch For more m detailed information refer to section on Water Supply Requirements D0741 Wrench Screwdriver Pliers Level BE N Figure 1 6 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Installing the Washer NOTE If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up Step 1 Remove the Shipping Brace and Shipping Plug TLW521N 1 Shipping Brace 2 Shipping Plug Figure 2 NOTE Install dryer before washer This allows room for attaching exhaust duct Move washer so that it is within 1 2 meters 4 feet of desired area of installation Remove the shipping brace from under the lid The plastic2. e Add Water to the Washer Switch W315IE0A C CHECK
3. air cushions may have to be installed if the pipes knock or pound when flow of water stops The risers are more efficient when installed as close as possible to the water supply faucets refer to Figure 19 woos 1 Risers Air cushions 2 Water Supply Faucets Figure 19 16 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Information for Handy Reference Date Purchased Model Number Serial Number Store Name Store Address Phone Number Service Agency Service Agency Address Phone Number NOTE Record the above information and keep your sales slip Model and serial numbers are located on the nameplate Customer Care Centre and Information 1300 652 100 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Notes 18 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 e Remove the Shipping Brace and Shipping Plug e Wipe Out Inside of Washtub e Connect Drain Hose to Drain Receptable CHECK Installer Checklist Fast Track for Installing the Washer Refer to the manual for more detailed information Position and Level the Washer qa LEVEL 7 D255l TLW521N e Plug In the Washer W504SE1B
4. shipping plug will be released from the base of the washer when removing the cardboard base from the washer Installation NOTE Do not tilt washer to front or sides when moving The shipping brace and plug should be saved and must be reinstalled whenever washer is moved or transported to a new location This will prevent damage to washer components NOTE Refer to your Use and Care Guide for instructions on reinstalling shipping brace and shipping plug Step 2 Wipe Out Inside of Washtub Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub W371 Figure 3 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 7 Installation Step 3 Connect Fill Hoses NOTE Refer to section on Water Supply Requirements before connecting fill hoses The appliance is to be connected to the water mains using new hose sets and old hose sets should not be reused Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the filter screens in the fill hoses or the screens in the water mixing valve NOTE When installing in a newly constructed or renovated building it is very important to flush the lines since build up may have occurred during construction Remove the two screened filter washers and the two plain rubber washers f
5. the outlet have a proper outlet installed by a qualified electrician NOTE Have a qualified electrician check the polarity of the wall receptacle If a voltage reading is measured other than that illustrated the qualified electrician should correct the problem If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent STANDARD 240 VOLT 50 HERTZ 3 WIRE EFFECTIVELY EARTHED CIRCUIT 240 VOLTS 50 HERTZ 240 VOLTS 50 HERTZ W504S 1 Power Cord 2 Earth Ground Prong Figure 17 14 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Water Supply Requirements Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for sucha period and before using the washer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable Do not smoke or use an open flame during this time W029 NOTE Water supply faucets must fit standard 3 4 14 BSP metric female couplings DO NOT USE SLIP ON OR CLAMP ON CONNECTIONS NOTE Water supply faucets should be readily accessible to permit turning them off when washer is not being used W1871 Water Supply Faucets Cold
6. Automatic Washers UONUI U SUI Keep These Instructions for Future Reference If this machine changes ownership this manual must accompany machine Part No 38910R8 February 2007 Table of Contents Replacement PariS asns reeeo eresi iaoi s AE EEEE ACET eeek 3 Installation RS nat eA ton uno AEL RE DEA ASt 5 Dimensions and Specifications 5 Before YOU Starts ete entra tte nt dote death ae 6 Tool nn ee A Re ee Me ee 6 Electrical ist sieste lalestalocseisttiadhslsdayebttliuethasioes 6 MAL ds nn ee en ide nl te 6 Installing the Washer ssiarssns ee een tete Trade 7 Step 1 Remove the Shipping Brace and Shipping Plug 7 Step 2 Wipe Out Inside of Washtub 7 St p 3 Connect Pill HOSESo iieo una 8 Step 4 Connect Drain Hose to Drain Receptacle eee 9 Step 5 Position and Level the Washer cc eeeeeeeesseeseeeeeceeeeenees 12 Step 6 Plug In the Washer 13 Step 7 Add Water to the Washer 13 Step 8 Check Lid Switch 13 Step 9 Check Installation e 13 Electrical Requirements i 14 Farthing Instructions tccvs sscesselaleeissessedspsiestatacsstingt tavetlceapessesduebbaetuats 14 Water Supply Requirements cece eeeeeecsecseeeeeeeeeeseeaeceaecnseeeneeee
7. Water Connection Hot Water Connection Fill Hoses BE ND Figure 18 Installation Water Temperature Cold Recommended cold water temperature is 10 to 24 Celsius 50 to 75 Fahrenheit Hot Recommended hot water temperature is 60 to 66 Celsius 140 to 150 Fahrenheit Warm Mixture of hot and cold water Warm water temperature is dependent upon the water temperature and the pressure of both the hot and cold water supply lines IMPORTANT Turn off water supply faucets after check out and demonstration Owner should turn off water supply whenever there will be an extended period of non use NOTE A longer fill hose is available as optional equipment at extra cost if the hose supplied with the washer is not long enough for the installation Order hose as follows Part Number WA003 2 5 m Inlet Hose 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 15 Installation Water Pressure Pressure must be a minimum of 138 to a maximum of 827 kPa 20 to 120 pounds per square inch static pressure measured at the faucet NOTE For water pressure over 827 kPa 120 pounds per square inch we recommend the installation of a pressure limiting valve Part Number PSL50DK This item may be purchased by calling 1300 652 100 NOTE Water pressure under 138 kPa 20 pounds per square inch will cause an extended fill time in the washer Risers Risers or
8. dpipe sink wall or laundry tub Follow these instructions to properly install the drain hose IMPORTANT Drain receptacle must be capable of handling a minimum of 32 cm 1 1 4 inch outside diameter drain hose W3241 1 Retainer Clamp Standpipe Adapter Figure 5 Installation Standpipe Installation Place the adapter into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose approximately 30 cm 12 inches down from the top of pipe and tighten strap to hold hose to standpipe This will prevent the drain hose from dislodging from drain receptacle during use IMPORTANT To prevent siphoning do not place any ribbed portion of the drain hose into the standpipe 91 44 cm 36 in RECOMMENDED HEIGHT 4 TLW1961N Drain Hose Sleeve Ribbed Portion of Drain Hose Standpipe Adapter Tie Down Strap Standpipe 5 08 cm 2 in or 4 cm 1 1 2 in Diameter a ND Figure 6 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 9 Installation High Standpipe Installation Place the adapter into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose approximately 30 cm 12 inches down from the top of pipe and tighten strap to hold hose
9. n hose MUST be secured to one of the inlet hoses using the beaded tie down strap from accessories bag NOTE End of drain hose must not be below height of cabinet top W3291 1 Tie Down Strap Tape if necessary 2 Standpipe Adapter Figure 10 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11 Installation Laundry Tub Installation For this type of installation the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use Use the beaded tie down strap supplied in accessories bag to secure hose We recommend leaving the standpipe adapter on the drain hose for this type installation TLW1964N 1 Tie Down Strap Tape if necessary Figure 11 Step 5 Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing Place rubber feet on all four leveling legs Place washer in position on a clean dry and reasonably firm floor Installing the washer on any type of carpeting is not recommended Loosen 7 8 inch locknuts and adjust the two front leveling legs Once adjusted tilt the unit forward on front legs and lower back down into position to set the rear self leveling legs Washer must not rock After washer is at desired height tighten locknuts securely against bottom of washer base If these lockn
10. ndry Systems LLC DO NOT COPY or TRANSMIT 13 Installation Electrical Requirements 240 Volt 50 Hertz with 3 Prong Earthing Plug NOTE The wiring diagram is located in the control hood To reduce the risk of fire electric shock or personal injury all wiring and earthing MUST conform with the latest edition of the National Electrical Code ANSI NFPA 70 and such local regulations as might apply It is the customer s responsibility to have the wiring fuses and circuit breakers checked by a qualified electrician to make sure your home has adequate electrical power to operate the washer DO NOT OVERLOAD CIRCUITS DO NOT USE ADAPTER DO NOT USE AN EXTENSION CORD Doogl Figure 16 Earthing Instructions The washer must be earthed In the event of malfunction or breakdown earthing will reduce the risk of electric shock by providing a path of least resistance for electric current The washer is equipped with a cord having an equipment earthing conductor and a 3 prong earthing plug The plug must be plugged into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinances Improper connection of the equipment earthing conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the washer is properly earthed Do not modify the plug provided with the washer if it will not fit
11. rom accessories bag and install them according to Figure 4 IMPORTANT Thread hose couplings onto valve connections finger tight then approximately 1 4 turn with pliers DO NOT cross thread or overtighten couplings 4 W5201 1 Filter Washer Screen must be facing outward 2 Fill Hose 3 Rubber Washer Plain 4 Install this end of hose blue coupling to valve connections at rear of washer 5 Install this end of hose white coupling to water supply faucet Turn water on and check for leaks If leaks are found retighten the hose couplings Continue tightening and rechecking until no leaks are found IMPORTANT Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a yearly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years Figure 4 8 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Step 4 Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp Find the instructions on the following pages that are appropriate for your type of drain receptacle standpipe high standpipe low stan
12. s 15 Water Temperature cole eeens eset Ee iae AKE a o E i EE Ria 15 Water Pressure ssip mnipe eiii e a E E E Ea 16 A E EAE E E tn etes 16 Information for Handy Reference 17 Installer Checklist ieta iiaii iiai Back Cover Copyright 2007 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 1 Notes Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Replacement Parts If replacement parts are required contact the source from which you purchased your washer 38910 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Notes Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Installation Dimensions and Specifications 56 2 cm 22 13 in 71 1 cm 28 in nDO E z Z 2 5 o o N t a S T 73 7 cm 29 in 65 cm 25 6 in With leveling legs turned into base 134 6 cm 53 in
13. to standpipe This will prevent the drain hose from dislodging from drain receptacle during use Low Standpipe Installation No 562P3 Siphon Break Kit is required for this type of installation This kit is available as optional equipment at extra cost through an authorized dealer or parts distributor Installation instructions are supplied with the kit W5128 1 562P3 Siphon Break Kit 2 Drain Hose 3 Standpipe TLW1962N 1 Standpipe Adapter 7 2 Drain Hose Figure 8 3 Tie Down Strap 4 Standpipe Standpipes higher than 122 cm 4 ft are not recommended Figure 7 10 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Sink Installation For this type of installation use the beaded tie down strap supplied in accessories bag or use a large wire tie available from your local hardware store and secure the drain hose to the cabinet top hinge Refer to Figure 9 This will prevent the drain hose from dislodging during use We recommend leaving the standpipe adapter on the drain hose for this type installation TLW1963N 1 Drain Hose 2 Cabinet Top Hinge 3 Tie Down Strap or Wire Tie Figure 9 Installation In the Wall Installation For installations of this type the drai
14. uts are not tight washer will not remain stationary during operation Improper installation or flexing of a weak floor will cause excessive vibration Do not slide washer across floor once the leveling legs have been extended as legs and base could become damaged Recheck to make sure washer does not rock wi79l Level Washer Base Locknut Leveling Leg Rubber Cup a ND Figure 12 12 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 38910 Installation Step 6 Plug In the Washer Step 8 Check Lid Switch Refer to section on Electrical Requirements and plug Washer should stop spinning when lid is opened the washer in W376IE0C Figure 15 Step 9 Check Installation Figure 13 Refer to Installer Checklist on the back cover of this Step 7 Add Water to the Washer manual and make sure that washer is installed correctly To prevent damage to pump do not run washer before i adding at least one quart water to the tub If the washer is run before any water is added the pump seal may overheat causing the pump to leak Once installed the water retained in the drain system from the previous cycle will provide sufficient cooling to prevent pump seal damage NOTE The agitator should not be removed except for service The washtub is designed to be self cleaning W3911 Figure 14 38910 Copyright Alliance Lau
Download Pdf Manuals
Related Search