ALCATEL Mobile Phones F200 TRIO User's Manual
Contents
1. 8 REGISTRATION Your handset and base station is pre registered Up to five handsets can be registered to a single base station If for some reason the handset is not registered to the base station al flashes even when the handset is near the base station register your handset according to the following procedure 1 Press and hold on the base station for about five seconds the base station is entered into registration mode 2 Press amp and amp to select REGISTRATION 3 Press and you are requested to enter the 4 digit system PIN default PIN is 0000 4 Enter the 4 digit system PIN 5 Press 85 to confirm If the handset registration is successful you will hear a confirmation tone and the ul will stop flashing The handset will automatically be allocated the next available handset number This handset number is shown in the handset display in standby mode If the handset registration is unsuccessful the al will still flash 9 TECHNICAL DETAILS Free Field Range Up to 300 metres Up to 50 metres average values 100 hours standby Three Way Conference Yes 1 outside correspondent 2 internal correspondents Electrical Connection Base Base main adaptor Mains Adaptor Charger Model No SOO4LV0600030 Input 100 240 V 50 60 Hz 0 15A Output 6 V DC 300 mA Charger adaptor Model No SOO4LV0600030 Input 100 240 V 50 60 Hz 0 15A Output 6 V DC 300 mA Only use the2. 1 Use only the supplied NiMH rechargeable batteries 2 If the handset will not be used for a long time disconnect and remove the batteries to prevent possible leakage 3 2 Connecting the Base Station 1 Plug one end of the telephone line cord into the telephone jack on base bottom 2 Plug the small end of power adapter into a power jack on base bottom 3 Connect the power supply plug to the base jack horizontally and route the power supply cord through the slot 4 Plug the large end of power adapter into a wall power outlet 5 Plug the other end of the telephone line cord in to the telephone jack or micro filter 6 Always use the cables provided in the box If you have broadband service a micro filter not included is required 3 3 Connecting the Charger s for Duo Trio models Plug the power adapter into mains socket If you have a Broadband line If you connect your telephone to a line with a broadband connection you will need to insert a micro filter between the telephone and the telephone line otherwise you may get interference between the telephone and the broadband which could cause problems In a home with broadband every telephone must have a micro filter connected not just the one at the telephone point that your modem is connected to If you need more broadband micro filters contact your broadband supplier q D ATLINKS
3. with names and numbers Each phonebook entry can have a maximum of 20 digits for the phone number and 12 characters for the name You can also select different ringtones for your phonebook entries Phonebook entries are stored alphabetically by name 5 1 Add a New Phonebook Entry In idle 1 Press w to access the phonebook OR Press 25 and amp to select PHONEBOOK main menu item and then press 8 to access the phonebook Press 24 to select ADD Press 2 to enter the name Press to enter the number Press 25 and amp to select the desired ringtone for your phonebook entry 6 Press 24 to store the phonebook entry aS 5 2 Call from the Phonebook In idle 1 Press w to access the phonebook OR Press G and amp to select PHONEBOOK main menu item and then press to access the phonebook 2 Press or C Versatis F250 Only to dial out to the selected phonebook entry 6 CALLER DISPLAY NETWORK DEPENDENT This feature is available if you have subscribed the Caller Line Identification service with your telephone service provider Your phone can store up to 20 received calls with date time information in the Call List The number will be shown on the LCD when the phone is ringing If the number matches with one of the entries in your Private Phonebook the caller s name stored in the private phonebook will be displayed alternatively with t
4. www atlinks com ATLINKS Europe 22 quai Gallieni 92150 Suresnes France ATLINKS 2011 Reproduction prohibited The Manufacturer reserves the right to modify the specifications of its products in order to make technical improvements or comply with new regulations ALCATEL and ATLINKS are registered trademarks The Alcatel logo and Alcatel name are trademarks of Alcatel and used under licence by ATLINKS F200 F200 Duo Trio F250 F250 Duo Trio A W No 10000259 Rev 1 EN Printed in China 4 USING YOUR PHONE 4 1 Make a Call 4 1 1 Preparatory Dialing Enter the phone number and press R or CO Versatis F250 Only to dial the number Press to clear the entry 4 1 2 Direct Dialing Press or CO Versatis F250 Only to take the line and enter the phone number 4 1 3 Dial from Direct Memory Keys In idle or off hook mode press and hold 2 J 2 2 to dial the direct memory number You have to store number to the related key first See section 7 4 for reference 4 1 4 Call from the Redial List Press Versatis F200 Only or Versatis F250 Only to access the redial list and press 4 9 to select the desired redial number Press or CO Versatis F250 Only to dial out to the selected redial number 4 2 Handset Speakerphone Versatis F250 Only During a call you can press _ _ to alternate between handsfree and normal handset use 5 PRIVATE PHONEBOOK Your phone can store up to 50 private phonebook entries
5. base or in use 1 4 Display Icons and Symbols The LCD display gives you information on the current status of the telephone i Steadily on when the handset is in range of the base J Flash when out of range of the base or not registered to the base Steadily on when an intercom is in progress Flash when there is an incoming internal call Indicate a call is in progress Versatis F250 only Indicate that handsfree is being used y y iq Steadily on when an alarm is set Flash when the alarm time set before reaches O oo Indicate that the keypad is locked Indicate when there are received new Voice Message Waiting VMWI not yet read Disappear when all the voice messages have been read Network service dependent Indicate that the ringer is switched off i Indicate when the battery is fully charged Whole icon flashes when the battery performs initial charging Internal block icon flashes when the battery is in final charging stage Indicate when the battery needs charging Flash when low battery power level is detected Indicate when more characters are existed before the text currently displayed Indicate when more characters are existed after the text currently displayed Indicate when new call is received Turn off when new call has been read Scroll up down the menu items Phonebook list Redial list Call List a VY a D 2 PRECAUTIONS The signal quality will depend on the location a
6. 11 2009 EN 301406 V2 1 1 2009 ATLINKS EUROPE 92150 SURESNES FRANCE 22 Quai Gallieni With the essential requirements and other relevant requirements of the R amp TTE Directive 1999 5 EC based on the followin and other normative documents the Council with regard to ec With Commission regulation EC and of the Council with regard to electronic household and office equipment external power supplies Declare under our sole responsibility that the products Alcatel Versatis F200 Versatis F200 Duo Versatis F200 Trio Versatis F250 Versatis With Commission regulation F250 Duo and Versatis F250 Trio comply This conformity is understood as being effective if the product for which it is given is installed and used accordin the user s guide Suresnes April 20th 2011 Didier GOUJARD CEO ATLINKS EUROPE We
7. ALCATEL VEISATFES SATS ersak S F200 F200 Duo F200 Tro VEISATK S YersatisS eratis F250 F250 Duo F250 Tro In keeping with our environmental preservation and compliance commitment we include mini guides in our packaging More complete instructions and online assistance are available on our website www atlinks com ECOIOGIC attitude 1 GETTING TO KNOW YOUR PHONE 1 1 Handset Overview Versatis F200 Only tL ear In idle mode Press to access the main menu In sub menu mode Press to confirm the selection During a call Press to access Intercom Phonebook Redial List Call List 2 In main menu mode Press to go back to idle screen In sub menu mode Press to go back to previous level In sub menu mode Press and hold to go back to idle screen In editing predialing mode Press to clear a character digit In editing predialing mode Press and hold to delete all the characters digits During a call Press to mute unmute the microphone In idle mode Press to intercom another handset In ringing Press to suppress handset ringer 3 A In idle mode Press to access the call list In menu mode Press to scroll up the menu items In Phonebook list Redial list Call List Press to scroll up the list During a call Press to increase the volume In ringing Press to increase the ringer volume 4 9 In idle mode Press to access the redial list In menu mode Press to scroll down the menu items In Phonebook list Redial list Call lis
8. adaptors supplied with the telephone Single phase AC excluding IT installations defined by the EN60950 standard Caution The network voltage is classified as a hazard by the criteria of this standard Appliance designed for connection to a TNV3 class telecommunications network voltage analogue telephone line as defined by the EN60950 standard AAA 1 2 V 400 mA Only use the batteries supplied with the telephone Use any other type of battery presents a risk of explosion Used batteries must be disposed of in compliance with current environmental protection regulations Operating Temperature From 5 C to 40 C Values may vary according to environment Depending on initial battery charge Telephone Connection Batteries 10 TROUBLESHOOTING If you have difficulty with your phone please try the suggestions listed below As a general rule if a problem occurs remove the batteries from all the handsets in your installation for about 1 minute then disconnect and reconnect the power supply to the base and reinstall the handset batteries Problem Check the connections Unplug and plug back in the mains Check that the telephone line cord has been plugged into the base station and the phone socket Check the base station plug and the 220V plug remove and plug in Wait until the line is unoccupied The connection cord of the base station is not No dialing tone when pressing R key p
9. appropriate local collection point or leave it with the vendor when buying a new appliance If you are a professional user please follow your supplier s instructions If the appliance is rented to you or left in your care please contact your service provider Keen to preserve the environment ATLINKS has equipped this appliance with a switching power supply offering better energy efficiency The advantages include not only very low electricity consumption but also a more compact format than the conventional power supply units used by the previous range The used batteries from your telephone if it has batteries must be disposed of in compliance with current environmental protection regulations Comply with your local regulations Return your batteries to your reseller or dispose of them at an approved recycling centre Help us protect the environment in which we live g standards g to the instructions provided in no 1275 2008 of December 17 2008 implementing Directive 2005 32 EC of the European Parliament ecodesign requirements for standby and off mode electric power consumption of electrical and R amp TTE DECLARATION OF CONFORMITY DOC EC N 278 2009 of April 6 2009 implementing Directive 2005 32 EC of the European Parliament and of odesign requirements for no load condition electric power consumption and average active efficiency of EN 301489 01 V1 8 1 2008 EN 301489 06 V1 3 1 2008 EN 60950 1 2006 A
10. ded that you avoid using this device during electrical storms Do not attempt to open the batteries as they contain chemical substances In the event of leakage avoid contact with the skin eyes nose and mouth In the event of contact rinse the affected part for about twenty minutes with running water and seek urgent medical attention Clean the product with absorbent paper or a dry cloth and contact your reseller for replacement batteries ATLINKS hereby declares that the following models conform to the essential requirements and other applicable provisions of European directive 1999 5 EC Versatis F200 Versatis F200 Duo Trio Versatis F250 Versatis F250 Duo Trio 12 ENVIRONMENT This symbol means that your inoperative electronic appliance must be collected separately and not mixed with the household waste The European Union has implemented a specific collection and recycling system for which producers are responsible This appliance has been designed and manufactured with high quality materials and components that can be recycled and reused Electrical and electronic appliances are liable to contain parts that are necessary in order for the system to work properly but which can become a health and environmental hazard if they are not handled or disposed of in the proper way Consequently please do not throw out your inoperative appliance with the household waste If you are the owner of the appliance you must deposit it at the
11. e speakerphone In Idle mode Predialing mode Redial list Call List Phonebook entry Press to make a call with speakerphone During ringing Press to answer a call with speakerphone 9 ALPHANUMERIC KEYPAD key in idle mode Press and hold to enable or disable the keypad lock key in idle mode Press and hold to turn on off the ringer key in call list mode Press to review caller s number if applicable 0 key in predialing number editing mode Press and hold to insert a pause 1 2 3 key in idle off hook mode press and hold to dial the stored direct memory number 10 In idle predialing mode Press to make a call In Redial list Call List Phonebook entry Press to make a call to the selected entry in the list During ringing Press to answer a call 1 3 Base Station Overview 1 Press on the base station to page your handset It will ring for approximately 60 seconds Press and hold on the base station for about five seconds the base station is entered into registration mode and allows handset registration 2 Steadily on while the handset is charging or in use Applicable only when the LED I O switch is slid to I Flash when receiving an incoming call Applicable only when the LED I O switch is slid to I 3 LED I O SWITCH Bottom of the Base Slide the switch to O position to turn off the base LED Slide the switch to I position to turn on the base LED when the handset is charging on the
12. he number The handset will ring with the melody associated with that phonebook entry If the caller number is disabled to send caller information WITHHELD will display If the caller number is not provided OUT OF AREA will display In standby if three unanswered calls are received 3 NEW CALLS will be displayed 6 1 View the Call List All received calls are saved in Call List with the latest call putting at the top of the list When the call list is full the oldest call will be replaced by a new call The unanswered call which has not been read is marked with a x at the centre of the bottom line of the display 1 Press amp to access the call list OR Press 2S and amp 9 to select CALL LIST 2 Press 4 9 to select the desired entry 3 Press to view the caller s number if applicable 6 2 Call from the Call List In idle 1 Press A to access the call list OR Press 2S and amp 9 to select CALL LIST 2 Press or C Versatis F250 Only to dial out to the selected phonebook entry 7 PHONE SETTINGS 7 1 Set the Ringer Melody for Internal External Calls 1 Press and 4 9 to select HS SETTINGS Press 24 and amp to select RING SETUP Press 24 and amp 9 to select INT RING or EXT RING Press 24 and amp to select the desired ringer melody from the melody list Note The respective ringer melody will be played while browsing the melody list 5 Pre
13. lugged in The adapter cord is not plugged in correctly in the base station The line is busy as another handset is used Wrong connection Use the original cord connection cord OUT OF Base station out of RANGE is range displayed Base station not connected to mains Reduce the range Connect base station to mains Check your Subscription with network Service not activated or wrong operator The call does not work No display Empty battery Recharge battery The store where you bought your telephone can also provide you with information and after sales support 11 SAFETY In the event of an electrical hazard the mains adapter acts as 230V power isolating device It should therefore as a precaution be installed close to the appliance and be easily accessible To disconnect the device from the primary power source the mains adapter must be removed from the 230V AC 50 Hz socket If the mains adapter fails it must be replaced by an identical model If not connected to the mains power or if there is a mains power failure telephones that use cordless handsets will not work You will then be unable to make or receive calls in the event of an emergency This is why we recommend that you also keep a conventional telephone one that doesn t require a power supply as a backup Do not use your telephone to notify a gas leak when standing in the vicinity of the leak It is recommen
14. nd environment of the base and handset Position your Versatis F200 Versatis F250 away from sources of excessive heat radiators direct sunlight etc and protect it from vibrations and dust Never allow your telephone to come into contact with water or other liquids or with aerosols To reduce the risk of interference and optimize reception take particular care not to install the base in the immediate vicinity of windows large metal objects reinforced concrete televisions music centres VCR or DVD players halogen lamps or heating devices fluorescent lighting burglar alarms microwave ovens computers etc This telephone requires an electrical power supply in order to function To clean your Versatis F200 Versatis F250 use an antistatic cloth lightly moistened with water NB Your Versatis F200 Versatis F250 is a DECT standard appliance designed to receive and transmit telephone calls It is designed for connection to the public telecommunications network 3 INSTALLING YOUR PHONE 3 1 Installing and Charging the Batteries 1 Slide down to open the battery compartment cover 2 Place the 2 supplied AAA rechargeable batteries as indicated Pay extra attention to direction of polarity 3 Slide the battery compartment cover back 4 Put the handset on the base and charge for 15 hours before using the handset for the first time The handset will give a beep when it is properly placed on the base or charger Notes
15. o go back to idle screen In sub menu mode Press to go back to previous level In sub menu mode Press and hold to go back to idle screen In editing predialing mode Press to clear a character digit In editing predialing mode Press and hold to delete all the characters digits During a call Press to mute unmute the microphone In idle mode Press to intercom another handset In ringing Press to suppress handset ringer 3 A In idle mode Press to access the call list In menu mode Press to scroll up the menu items In Phonebook list Redial list Call List Press to scroll up the list During a call Press to increase the volume In ringing Press to increase the ringer volume 469 In idle mode Press to access the redial list In menu mode Press to scroll down the menu items In Phonebook list Redial list Call List Press to scroll down the list During a call Press to decrease the volume In ringing Press to decrease the ringer volume During a call Press to end a call and go back to idle screen In menu editing mode Press to go back to previous menu In menu editing mode Press and hold to go back to idle screen In idle mode Press and hold to power off the handset In idle mode Press and hold to power on off the handset 6 R In idle predialing mode Press to insert a flash During a call Press to dial a flash 7 In idle mode Press to access the phonebook list 8 C During a call Press to turn on off th
16. ss to confirm el 7 2 Set the Ringer Volume 1 Press and 4 9 to select HS SETTINGS 2 Press amp and amp to select RING SETUP 3 4 Press 24 and 4 9 to select RING VOLUME Press 24 and amp to select the desired ringer volume a total of 6 ringer volume levels including VOLUME OFF Note The respective ringer volume will be played during your selection If VOLUME OFF is selected icon will display 5 Press 85 to confirm 7 3 Adjust Earpiece and Handsfree Versatis F250 Only Volume There are 5 levels VOLUME 1 to VOLUME 5 to choose from for each of earpiece and handsfree Versatis F250 Only volume During a call Press amp to select volume 1 5 The current setting is shown When you end the call the setting will remain at the last selected level 7 4 Store Direct Memory Access Number You can store three direct access numbers into digit KEY 1 KEY 2 and KEY 3 which will be convenient for you to dial to these numbers directly 1 Press and amp 9 to select HS SETTINGS 2 Press amp 6 and amp to select DIRECT MEM 3 Press 24 and 4 9 to select any one from KEY 1 KEY 2 and KEY 3 4 Press and then enter the number you would like to store or edit the number existed before 5 Press 2 to confirm Note Press and hold J or 2J to call the stored number
17. t Press to scroll down the list During a call Press to decrease the volume In ringing Press to decrease the ringer volume During a call Press to end a call and go back to idle screen In menu editing mode Press to go back to previous menu In menu editing mode Press and hold to go back to idle screen In idle mode Press and hold to power off the handset In idle mode Press and hold to power on off the handset 6 CR In idle predialing mode Press to insert a flash During a call Press to dial a flash 7 In idle mode Press to access the phonebook list 8 In idle mode Press to access the redial list 9 ALPHANUMERIC KEYPAD key in idle mode Press and hold to enable or disable the keypad lock key in idle mode Press and hold to turn on off the ringer key in call list mode Press to review caller s number if applicable 0 key in predialing number editing mode Press and hold to insert a pause 1 2 3 key in idle off hook mode press and hold to dial the stored direct memory number 10 In idle predialing mode Press to make a call In Redial list Call List Phonebook entry Press to make a call to the selected entry in the list During ringing Press to answer a call 1 2 Handset Overview Versatis F250 only 1 In idle mode Press to access the main menu In sub menu mode Press to confirm the selection During a call Press to access Intercom Phonebook Redial List Call List 2 E In main menu mode Press t
Download Pdf Manuals
Related Search