Airlink101 ASW324 User's Manual
Contents
1. IRLINK Quick Installation Guide 24 Port 10 100Mbps Fast Ethernet Switch Model ASW324 Ver 1A ie ees Trademarks Copyright 2009 Airlink101 Airlink101 is a registered trademark All other trademarks belong to their respective proprietors Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from Airlink101 Preface FCC Warning This device has been tested and found to comply with limits for a Class a digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the user s manual may cause interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures EM Introduction Congratulations on your purchase of the 24 Port 10 100Mbps Fast Ethernet Switch It is an easy installed network switch which helps you to extend your network structure quickly and reliably Purpose This Quick Insta2. feedback and pe help monitoring and troubleshooting when needed 6 8 10 12 14 16 18 20 2 24 INATAOOOOGOO000R Color The The port is respective ace transmitting polls or receivin successfully J No link data on the connected to Ethernet an Ethernet network AE Color D E a a WAOMO G Coo COCO C000 _ i j nm rh zZ OO O OG O On OO OO ene o M LNKIACT A A O 5 The respective PWR G 10A00M O O O 0 D See port is ir 00 port is connected to Figure 1 3 Front Panel view of the switch Green connected to N A the 10Mbps the 100Mbps Ethernet Ethernet network or no network link e POWER Power Indicator a Le Ree EPC 1ED Color The Switch is Standards power omen MESHES Na nope e IEEE 802 3 10BASE T IEEE 802 3u 100BASE TX and IEEE 802 3x Flow Control Network Cables e Ethernet Cables 2 pair UTP Cat 3 4 5 Twisted Pair UTP e Fast Ethernet 2 pair UTP Cat 5 Twisted Pair UTP Ports e 24x 10 100Mbps TX Auto Negotiation RJ45 Port Access Method e CSMA CD Transmission Method e Store and Forward MAC Address Table e 8K Built in Buffer e 1 25M bits Data Transfer Rate e Ethernet 10 20Mbps Half Full Duplex e Fast Ethernet 100 200Mbps Half Full Duplex Physical and Environmental e Power Input 100 240V AC 50 60Hz e Operation Temperature 0 C 50 C e Storage Temperature 20 C 70 C e Humidity 5 90 RH non condensi
3. just to the local power source automatically EF Connecting the Switch This section describes how to connect the Switch to your 10 100Mbps Fast Ethernet network 3 1 Connection Your network device i e computer switch IP Camera VoIP can be connected to any port of the Switch via a two pair Category 5 Cable If the LED indicators do not light up after 8 making a proper connection check your network device the cable the Switch conditions and connections 4 Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Free Voice Technical Support is only available within the hardware warranty 1 Year Limited Warranty from the date of purchase Customer is required to provide invoice as purchase evidence Network conditions and environmental factors as well as network overhead lower actual data throughput rate Copyright 2009 AirLink101 All rights reserved AirLink101 the stylized AirLink101 logo specific product designations and all other words and logos that are identified as trademarks and or service marks are unless noted otherwise the trademarks and service marks of AirLink101 All other product or service names are the property of their respective holders AirLink101 products are protected under numerous U S and foreign patents and pending applications mask work rights and copyrights
4. llation Guide tells you how to install your Switch and how to connect it to your Ethernet network Terms Usage In this manual the term Switch first letter upper case refers to your 24 Port 10 100Mbps Fast Ethernet Switch and switch first letter lower case refers to other Ethernet switches 1 1 Hardware Interface e 24 Port 10 100Mbps auto negotiation RJ45 Ports e All ports support auto MDI MDIX no need to use cross over cables 1 2 Panel 1 2 1 Front Panel The front panel of the Switch consists of LED indicators and 24 10 100Mbps ports The figure below shows the front panel of the Switch 104 o Ea E is a E m li C a jaarsssuseue P AA R oe Oe ee ee Abe m r r a aa T a coc cle eo oo Figure 1 1 Front Panel view of the Switch e 10 100Mbps Ports Port 1 24 These ports support 10 100Mbps and can operate in Half Full Duplex transfer modes These ports also support automatic MDI MDI X crossover detection giving true plug and play capability e LED Indicators Comprehensive LED indicators display the status of the switch and the network see Section 1 2 3 1 2 2 Rear Panel ji Jie Figure 1 2 Rear Panel view of the Switch e AC Power Connector Supports AC 100 240V 50 60Hz ONOTICE 3 e Port 1 24 10 100M Status LEDs Do not envelop Radiator Fan while the Switch is working 1 2 3 LED indicators information The front panel LEDs provide instant status
5. ng 2 Installing the Switch The site where you place the switch may greatly affect its performance When installing take the following into your consideration 2 1 Installation Follow the guidelines below to install the Switch Install the Switch in a fairly cool and dry place See the Technical Specifications for the acceptable temperature and humidity operating ranges Install the Switch on a sturdy level surface that can support its weight Connect the power cord to the Switch and the power outlet The distance is no more than 182cm Leave at least 10cm about 4 inches of space at the front and rear of the Switch for ventilation 2 2 Desktop or Shelf Installation When installing the Switch on the desktop or shelf please attach the rubber feet to the Switch Peel off the protective paper on the pads and attach them on the bottom of the Switch one at each corner 2 3 Rack Installation The Switch is rack mountable and can be installed on an EIA 19 inch equipment rack To do this first install the mounting brackets on the Switch s side panels one on each side secure them with the included screws and then use the screws provided with the equipment rack to mount the Switch 2 4 Power on the Switch The Switch has a universal power supply ranging from 100V to 240V AC 50 60Hz power source The AC power connector is located at the rear of the unit adjacent to and the system fan The switch s power supply will ad
Download Pdf Manuals
Related Search