Air King Fan User's Manual
Contents
1. a soft cloth and a mild soap solution such as liquid dish 5 16 x 2 U Bolt washing detergent Clamp Plate CAUTION Do not use gasoline benzine thinner harsh cleaners 5 16 13 Nut etc which will damage the Fan Dry all parts with a soft cloth completely before reconnecting to power supply STORAGE When not in use keep unit in a clean dry place MOTOR IS PERMANENTLY LUBRICATED 5 16 Lock Washer 5 16 Flat Washer 1 4 20 x 1 2 Set Screw Secondary Support Kit Allen Key A A AININ LIMITED WARRANTY SHOULD ACCESSORY PARTS BE NEEDED CONTACT THE MANUFACTURER FOR IN WARRANTY REPLACEMENT PARTS A COPY OF PROOF OF PURCHASE MUST BE INCLUDED ALONG WITH THE TYPE AND STYLE WHICH IS LOCATED ON THE BOTTOM OF YOUR APPLIANCE This product is warranted for one year from the date of original purchase against defects in workmanship and or materials At our option parts that prove to be defective will either be repaired or replaced or the whole product will be replaced Should electrical or mechanical repair become necessary during the warranty period send your complete product postage or freight pre paid to the nearest service center Call the number below for the service station nearest you Should a part need replacement you must give us the type and style of your appliance You will find this at the bottom of the appliance In either case a copy of your proof of purchase is requested This warranty does2. not apply if the damage occurs because of accident improper handling or operation shipping damage abuse misuse unauthorized repairs made or attempted or the use of the product for commercial service ALL WARRANTIES EXPRESSED OR IMPLIED LAST FOR ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE THIS WARRANTY DOES NOT COVER LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY CAUSE WHATSOEVER Some states do not allow limitations on how long any implied warranty lasts or the exclusion or limitation of incidental or consequential damages so that the above limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state FOR PARTS Check package contents If parts are missing or replacement parts required please call our PARTS DEPARTMENT TOLL FREE AT 1 800 966 2028 MONDAY THROUGH FRIDAY BETWEEN THE HOURS OF 8 AM AND 4 PM EST PLEASE DO NOT RETURN PRODUCT TO PLACE OF PURCHASE Reference the type and style of product located on the underside of the product when you call FOR TECHNICAL ASSISTANCE and SERVICE CENTER LOCATIONS For any questions comments or the location of your nearest service center PLEASE CALL OUR TOLL FREE HOTLINE AT 1 800 233 0268 MONDAY THROUGH FRIDAY BETWEEN THE HOURS OF 8 AM AND 5 PM EST Please reference product name and model no when you call Appliance Service Dept P O Box 569 Franklin TN 37065 0569 PLEASE D
3. O NOT SEND PRODUCT TO THIS LOCATION New 6 01 2 5084036
4. OPERATING INSTRUCTIONS amp PARTS MANUAL Ventilation Products HIGH VELOCITY I BEAM MOUNT FAN 18 45 7 cm MODEL 9618 READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE INSTALL OPERATE OR MAINTAIN THE PRODUCT DESCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE DESCRIPTION The AirKing 18 45 7 cm Beam Mount Fan features Pull Cord operation and a 3 paddle Fan Blade This Fan has a permanently lubricated motor with a 9 ft 2 74 m 18 3 cord set and are constructed of sturdy powder coated steel SPECIFICATIONS 120 V 50 60 Hz 18 45 7 cm Model 9618 Pull Cord 360 UL Listed Close mesh Fan guard meets OSHA requirements GENERAL SAFETY INFORMATION 1 Make certain that the power source conforms to the electrical require ments of the Fan 2 The power cord is equipped with a three prong grounded plug that must be inserted into a matching receptacle Under no circumstances must the grounding prong be cut off the plug Where a two prong wall receptacle is encountered it must be replaced with a properly grounded three prong receptacle installed in accordance with the National Electrical Code NEC and all applicable local codes and ordinances This work must be done only by a qualified electrician using copper w
5. e surface when operating 8 DO NOT mount Fan near windows or bay doors Rain may create an electrical hazard 9 Completely reassemble Fan according to instructions before recon necting to power supply I BEAM MOUNT INSTALLATION 1 Locate the L shaped pipe to the desired location on the l Beam flange Install the 5 16 x 2 U Bolt over the pipe and through the clamping plate holes The flat part of the clamping plates fits on the Beam flange and the end with the slight bend goes against the pipe Install flat washers lock washers and nuts Finger tighten the nuts on the U Bolt Figure 1 Slide the clamping plates onto l Beam flange until U Bolts contact flange Adjust L shaped pipe so forward clamp plate is as close to the label at the bend as possible Tighten nuts on bolt so pipe does not move 5 Screw on the adapter mount as far as it will go onto the L shaped pipe Tighten set screw in pipe coupling with Allen Key provided Tighten Bolt on Fan Mount after positioning fan to desired position on A O 5 16 Nut 5 16 Lock Washer Tighten Clamp Plate Here 5 16 Flat Washer 1 4 Set Screw Tighten Bolt Figure 1 5084036 MODEL 9618 CAUTION THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USEDANYTIME THE CIRCULATORIS MOUNTED OVERHEAD FOR ADDITIONAL SAFETY SETON DARY SUPPORT CABLE Loop one end of Cable around the Large Diameter Wires of both the Front and Rear Circulator Gua
6. ire only WARNING USE OF A THREE PRONG TO TWO PRONG ADAPTERIS NOT RECOMMENDED IMPROPER CONNECTION MAY CREATE THE RISK OF ELECTROCUTION USE OF SUCH ADAPTERS ARE NOT PERMITTED IN CANADA 3 Where possible avoid the use of extension cords If they must be used minimize the risk of overheating by ensuring that they are UL listed and of the proper gage and length Never use a single extension cord to operate more than one fan 4 Do not insert fingers or foreign objects into the fan Do not block or tamper with the fan in any manner while itis in operation Do not touch the fan while in operation or just after it has been turned off as some parts may be hot enough to cause injury 5 Unplug power cord before installing or servicing the fan WARNING DO NOT DEPEND UPON THE ON OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN ALWAYS UNPLUG THE POWER CORD 6 This fan is intended for general use ONLY It must NOT be used in potentially dangerous locations such as flammable explosive chemi cal laden or wet atmospheres New 6 01 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE CAUTION BECAUSE OF SIZE AND WEIGHT OF THIS FAN MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN FAN COM ING APART DURING OPERATION AND OR PERSONAL INJURY 7 Be sure Fan is mounted to a stabl
7. rd Figure 2 2 Attach a Cable Clamp with the U on the tail side of the loop leaving a tail approximately 1 to 2 inches Tighten Clamp Nuts Make sure no part of the Cable interferes with the Blade Figure 2 3 Wrap the other end of the Cable around a secure building joist truss l beam or other support near the Fan Do not attach cable to I beam mount pipe Figure 3 Take up all excess slack in the Cable CAUTION USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN 4 Attach the remaining Cable Clamp as indicated in Step 2 The excess tail should be trimmed to extend 1 to 2 inches past the Clamp 5 Check the Assembly to assure the Blade is free of all obstructions CAUTION USE OF THE SECONDARY SUPPORT CABLE DOES NOT GUARANTEE PROTECTION AGAINST INJURY OF PERSONS MOUNTING OF BOTH THE CIRCULATOR AND CABLE COULD FAIL IF SUBJECTED TO ABUSE NEGLECT OR IMPROPER INSTALLATION PART BAG Figure 2 Figure 3 Large Guard Wires Secondary Support Cable N OPERATION 1 Plug the power cord into a properly grounded three prong receptacle 2 Using the Pull Cord Switch set the desired Fan Speed 3 WARNING This fan should be used only in a clean dry environment Mounting of this product in any way other then specified in the instruction sheet will null and void the manufacturers warranty MAINTENANCE Qty WARNING ALWAYS UNPLUG CORD BEFORE SERVICING Description i CLEANING Use
Download Pdf Manuals
Related Search